Study guide

14.3 ALARA, Stay-Time, and the Inverse Square Law

CIH Certified Industrial Hygienist Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: The CIH Exam and How to Use This Guide

1.1 CIH Exam Format, Scoring, and Test-Day Logistics 1.2 Eligibility, Application Windows, Fees, and Certification Maintenance 1.3 The BGC Blueprint, Subject Areas, and a Calculation-First Study Plan

2 Chapter 2: Basic Science & Calculations

2.1 Gas Laws and Vapor Calculations 2.2 Unit Conversions: ppm, mg/m³, and Standard Temperature/Pressure 2.3 Fluid Mechanics and Airflow Fundamentals

3 Chapter 3: Air Sampling & Instrumentation

3.1 Active and Passive Air Sampling Strategies 3.2 Particulate and Aerosol Sampling 3.3 Direct-Reading Instruments and Calibration

4 Chapter 4: Analytical Chemistry & Lab Methods

4.1 Gas Chromatography and Mass Spectrometry 4.2 High-Performance Liquid Chromatography and Ion Chromatography 4.3 Spectroscopy and Elemental Analysis 4.4 Gravimetric, Microscopy, and Wet Chemical Methods 4.5 Laboratory Quality Assurance, Chain of Custody, and Desorption Efficiency

5 Chapter 5: Biostatistics & Epidemiology

5.1 Lognormal Distributions and Exposure Data Statistics 5.2 Upper Confidence Limits (UCL95) and Compliance Decision Rules 5.3 Epidemiological Study Designs and Measures of Association 5.4 Sampling Strategy: Sample Size, Power, and Worker Selection

6 Chapter 6: Toxicology & Biological Monitoring

6.1 Dose-Response Relationships and Points of Departure 6.2 Toxicokinetics: Absorption, Distribution, Metabolism, and Elimination 6.3 Aerosol Deposition, Clearance, and Respiratory Tract Dosimetry 6.4 Hepatic, Renal, Neurologic, and Hematologic Target Organ Toxicity 6.5 Pulmonary Toxicology, Carcinogenicity, and Reproductive Hazards 6.6 OEL Frameworks, Classifications, and Excursion Limits 6.7 Chemical Mixtures and Extended Work-Shift OEL Adjustments 6.8 Biological Exposure Indices (BEIs) and Biomonitoring

7 Chapter 7: Biohazards & Indoor Environmental Quality

7.1 Mold, Fungi, and Microbial Contaminants 7.2 Infectious Agents, Bloodborne Pathogens, and Biosafety Levels 7.3 Indoor Environmental Quality (IEQ) Investigations 7.4 Sanitation, Potable Water, and Personal Hygiene Programs

8 Chapter 8: Community Exposure & Environmental Health

8.1 Clean Air Act Framework, NAAQS, and New Source Review 8.2 Hazardous Air Pollutants, CEMS, and EPA Reference Methods 8.3 Atmospheric Stability, Lapse Rates, and Plume Morphology 8.4 Gaussian Plume Modeling, Plume Rise, and Environmental Fate 8.5 HAZWOPER Scope, Mandates, and Training Tiers 8.6 Protection Levels, Site Zoning, Incident Command, and Decontamination 8.7 Water Pollution, Hazardous Waste, and Community Right-to-Know

9 Chapter 9: Health Risk Analysis & Hazard Communication

9.1 GHS Hazard Classification: Health and Physical Hazard Criteria 9.2 GHS Labels, Safety Data Sheets, and Trade Secret Rules 9.3 The AIHA Exposure Assessment Strategy and Similar Exposure Groups 9.4 Qualitative Exposure Profiling and the AIHA Risk Matrix 9.5 Quantitative Health Risk Characterization: HQ, HI, and ELCR 9.6 NIOSH Occupational Exposure Banding 9.7 Risk Communication and Reporting to Affected Parties

10 Chapter 10: Industrial Ventilation Principles & LEV Design

10.1 Elimination, Substitution, Isolation, Containment, and Process Change 10.2 LEV Hood Taxonomy and Capture Velocity Selection 10.3 Hood Airflow Equations, Entry Losses, and Hood Static Pressure 10.4 Particulate Transport Aerodynamics and Duct Sizing 10.5 Duct Friction, Fitting Losses, and System Balancing 10.6 Fan Categories and Pressure Dynamics Across the Fan 10.7 System Curves, the Fan Laws, and Density Corrections

11 Chapter 11: General Ventilation, Air Cleaning & Diagnostics

11.1 Dilution Ventilation Principles and Steady-State Modeling 11.2 Transient Purging and Air Distribution Geometry 11.3 Particulate Air Cleaning: Cyclones, Baghouses, Scrubbers, and ESPs 11.4 Gaseous Emission Control and Air Cleaner Selection 11.5 Ventilation System Troubleshooting and Testing

12 Chapter 12: Noise Measurement & Hearing Conservation

12.1 Acoustic Physics and Decibel Mathematics 12.2 Sound Propagation, Octave Bands, and Frequency Weighting 12.3 Noise Dose Metrics and OSHA versus ACGIH Criteria 12.4 Exchange Rates, Extended Shifts, and Dosimetry Field Protocols 12.5 Engineering Noise Controls and Hearing Protector Attenuation 12.6 Hearing Conservation Programs and Standard Threshold Shifts 12.7 Hand-Arm and Whole-Body Vibration

13 Chapter 13: Thermal Stress Assessment & Control

13.1 Wet Bulb Globe Temperature (WBGT) and Heat Stress Indices 13.2 Heat-Related Disorders, Acclimatization, and Work/Rest Regimens 13.3 Cold Stress Evaluation and Wind Chill

14 Chapter 14: Ionizing Radiation Protection

14.1 Ionizing Radiation Physics and Radioactive Decay Kinetics 14.2 Radiation Units, Radiobiology, and Health Effects 14.3 ALARA, Stay-Time, and the Inverse Square Law 14.4 Shielding Physics, Material Selection, and Gamma Constants 14.5 Radiation Detection Instruments and Spectrometry 14.6 Personnel Dosimetry, Dose Limits, and Contamination Surveys

15 Chapter 15: Non-Ionizing Radiation & Laser Safety

15.1 The Non-Ionizing Spectrum and Static/ELF Field Exposures 15.2 Radiofrequency and Microwave Exposure: SAR, Standards, and Surveys 15.3 Ultraviolet, Visible, and Infrared Radiation Hazards 15.4 Laser Safety Classifications and Optical Density Calculations 15.5 Illumination, Lighting Design, and Visual Performance

16 Chapter 16: Non-Engineering Controls & Personal Protective Equipment

16.1 Respiratory Protection Programs and Assigned Protection Factors 16.2 Maximum Use Concentration, Oxygen Deficiency, and Breathing Air 16.3 Particulate Filters, Sorbent Cartridges, and Change Schedules 16.4 Respirator Fit Testing Protocols 16.5 Chemical Protective Clothing and Dermal Exposure Control

17 Chapter 17: Ergonomics & Workstation Design

17.1 Soft-Tissue Biomechanics and WMSD Pathophysiology 17.2 Ergonomic Risk Factors and Their Interaction Effects 17.3 The Revised NIOSH Lifting Equation 17.4 RULA, REBA, the Strain Index, and the ACGIH HAL TLV 17.5 Anthropometry and Workstation Geometry 17.6 VDT Workstations, Hand Tool Design, and Administrative Ergonomics

18 Chapter 18: Work Environments & Industrial Processes

18.1 Welding Fume Emissions, Metal Fume Fever, and Cr(VI)/Manganese Toxicology 18.2 Foundry Operations and Hot Work Fire Prevention 18.3 Vapor Degreasing, Pickling, Electroplating, and Cyanide Baths 18.4 Spray Coatings, Isocyanates, and Semiconductor Manufacturing 18.5 Confined Spaces and High-Hazard Industrial Operations 18.6 Asbestos, Lead, and Silica: Regulated Substance Programs 18.7 Abrasive Blasting and Surface Preparation

19 Chapter 19: IH Program Management & Professional Ethics

19.1 The BGC Code of Ethics: Canons and Enforcement 19.2 Professional Liability, Standard of Care, and Expert Testimony 19.3 Occupational Health & Safety Management Systems (ISO 45001, ANSI Z10) 19.4 Exposure Records Access and Medical Surveillance 19.5 OSHA Injury and Illness Recordkeeping and Enforcement

14.3 ALARA, Stay-Time, and the Inverse Square Law

Key Takeaways Explain This Topic AI

ALARA requires that doses be kept as low as reasonably achievable taking economic and social factors into account — it is an optimisation requirement layered on top of, not a substitute for, the regulatory dose limits.

NUREG-1530 Revision 1 (February 2022) sets the monetary value of averted dose at $5,200 per person-rem, replacing the older $1,000 and $2,000 figures used in earlier cost-benefit analyses.

Stay time equals the allowable dose divided by the dose rate, which makes time the simplest and cheapest control to implement through planning, rehearsal, and mock-ups.

For a point source the inverse square law gives I1·d1² = I2·d2², so doubling the distance cuts the dose rate to one quarter — the single highest-leverage protective action available in the field.

Last updated: August 2026

ALARA, Stay-Time, and the Inverse Square Law

External radiation protection is founded upon the philosophy of ALARA (As Low As Reasonably Achievable) , codified under 10 CFR 20.1101. The ALARA standard requires industrial hygienists and health physicists to make every reasonable effort to maintain occupational exposures as far below regulatory dose limits as practical, taking into account the state of technology, the economics of improvements relative to benefits, and public health impact. The three fundamental engineering and administrative pillars utilized to control external radiation fields are Time , Distance , and Shielding .

1. The ALARA Philosophy and Optimization Framework

The International Commission on Radiological Protection (ICRP) and the National Council on Radiation Protection and Measurements (NCRP) establish three core tenets governing radiation safety: +-------------------------------------------------------------------------------------------------+

  • | THE THREE PILLARS OF RADIATION PROTECTION |
  • | |
  • | 1. JUSTIFICATION: No practice involving radiation exposure should be adopted unless it |
  • | produces a net positive benefit to the exposed individuals or society. |
  • | |
  • | 2. OPTIMIZATION: All exposures must be kept As Low As Reasonably Achievable (ALARA), |
  • | economic and societal factors being taken into account. |
  • | |
  • | 3. DOSE LIMITATION:Individual doses must not exceed statutory regulatory occupational limits |
  • | (e.g., 5 rem/year whole body TEDE). |
  • +-------------------------------------------------------------------------------------------------+

In practical industrial hygiene engineering, ALARA involves formal quantitative cost-benefit analysis . The monetary value assigned to radiation dose reduction is set by NRC guidance. NUREG-1530, Revision 1 (issued February 25, 2022) raised the conversion factor from the long-standing $2,000 to $5,200 per person-rem ($520,000 per person-Sv, in 2014 dollars) averted, derived from a $9.0 million value of a statistical life and the EPA cancer mortality risk coefficient of 5.8 × 10⁻⁴ per rem. Older references that still quote $1,000 or $2,000 per person-rem predate that revision. If an engineered shielding modification costs less than the monetary valuation of the collective dose it prevents over the life of the facility, the modification is mandatory under ALARA.

2. Cardinal Principle 1: Time Optimization and Stay-Time Calculations

The cumulative absorbed or equivalent dose received by a worker is directly proportional to the total residence time spent in a radiation field: Dose ( D ) = Dose Rate ( D ˙ ) × Time ( t ) \mathbf{\text{Dose } (D) = \text{Dose Rate } (\dot{D}) \times \text{Time } (t)} Dose ( D ) = Dose Rate ( D ˙ ) × Time ( t )

Operational Time-Reduction Strategies

Dry-Run Rehearsals: Conducting end-to-end task simulations on non-radioactive "cold" mock-ups prior to entering high-radiation fields.

Pre-fabrication and Modular Assembly: Performing cutting, welding, prep work, and tooling calibrations in clean, unexposed staging areas.

Worker Rotation: Distributing high-dose tasks across multiple qualified individuals to keep individual exposures well below administrative action limits (note: rotation distributes dose across individuals but does not rate collective population dose).

Maximum Permissible Stay-Time Formulation

When workers must enter a high-radiation zone (e.g., D > 100 mrem/hr), the Stay-Time (Tstay) must be calculated in advance to ensure the worker does not exceed an assigned administrative dose ceiling (Dceiling): T stay = D ceiling − D accumulated D ˙ field \mathbf{T_{\text{stay}} = \frac{D_{\text{ceiling}} - D_{\text{accumulated}}}{\dot{D}_{\text{field}}}} T stay ​ = D ˙ field ​ D ceiling ​ − D accumulated ​ ​

3. Cardinal Principle 2: Distance and the Inverse Square Law

Increasing distance from a radiation source is the most effective and cost-efficient method of dose reduction. For a point source emitting isotropic radiation, the flux density (photons or particles crossing unit area per second) diminishes in proportion to the expanding surface area of a sphere (Asphere = 4π r²). +--------------------------------------------------------------------------+

  • | THE INVERSE SQUARE LAW |
  • | |
  • | I₁ • (r₁)² = I₂ • (r₂)² ==> I₂ = I₁ • (r₁ / r₂)² |
  • | |
  • | • Doubling Distance (2×) --> Dose Rate drops to 1/4 (75% reduction) |
  • | • Tripling Distance (3×) --> Dose Rate drops to 1/9 (89% reduction) |
  • | • 10× Distance --> Dose Rate drops to 1/100 (99% reduction)|

+--------------------------------------------------------------------------+ I 1 ⋅ r 1 2 = I 2 ⋅ r 2 2 ⟹ I 2 = I 1 ( r 1 r 2 ) 2 \mathbf{I_1 \cdot r_1^2 = I_2 \cdot r_2^2 \implies I_2 = I_1 \left(\frac{r_1}{r_2}\right)^2} I 1 ​ ⋅ r 1 2 ​ = I 2 ​ ⋅ r 2 2 ​ ⟹ I 2 ​ = I 1 ​ ( r 2 ​ r 1 ​ ​ ) 2

Where:

  • I1 = Dose rate (or intensity) at reference distance r1
  • I2 = Dose rate (or intensity) at target distance r2
  • r1, r2 = Distances from the source (must be in identical units)
  • Geometric Limitations of the Inverse Square Law

Point Source Criterion: The Inverse Square Law is mathematically valid only when the distance from the source (r) is at least five to ten times greater than the largest physical dimension (L) of the source (r ≥ 5L).

Line Sources (e.g., contaminated piping): Near a line source (r < L), radiation intensity decreases linearly with distance (I ∝ 1/r). At large distances (r >> L), it transitions into point-source behavior (I ∝ 1/r²).

Planar / Area Sources (e.g., contaminated floor plate): Directly adjacent to an infinite flat plane (r << dimensions), the dose rate is approximately constant and independent of distance . As distance increases far beyond the surface dimensions, it transitions to line-source and eventually point-source geometry. +--------------------------------------------------------------------------+

  • | SOURCE GEOMETRY DOSE PROFILES |
  • | |
  • | • Point Source: I ∝ 1 / r² (Standard Inverse Square Law) |
  • | • Line Source: I ∝ 1 / r (Close range, r < Length L) |
  • | • Planar / Area: I ∝ Constant (Immediate proximity, r << Area) |
  • +--------------------------------------------------------------------------+