Study guide

15.5 Illumination, Lighting Design, and Visual Performance

CIH Certified Industrial Hygienist Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: The CIH Exam and How to Use This Guide

1.1 CIH Exam Format, Scoring, and Test-Day Logistics 1.2 Eligibility, Application Windows, Fees, and Certification Maintenance 1.3 The BGC Blueprint, Subject Areas, and a Calculation-First Study Plan

2 Chapter 2: Basic Science & Calculations

2.1 Gas Laws and Vapor Calculations 2.2 Unit Conversions: ppm, mg/m³, and Standard Temperature/Pressure 2.3 Fluid Mechanics and Airflow Fundamentals

3 Chapter 3: Air Sampling & Instrumentation

3.1 Active and Passive Air Sampling Strategies 3.2 Particulate and Aerosol Sampling 3.3 Direct-Reading Instruments and Calibration

4 Chapter 4: Analytical Chemistry & Lab Methods

4.1 Gas Chromatography and Mass Spectrometry 4.2 High-Performance Liquid Chromatography and Ion Chromatography 4.3 Spectroscopy and Elemental Analysis 4.4 Gravimetric, Microscopy, and Wet Chemical Methods 4.5 Laboratory Quality Assurance, Chain of Custody, and Desorption Efficiency

5 Chapter 5: Biostatistics & Epidemiology

5.1 Lognormal Distributions and Exposure Data Statistics 5.2 Upper Confidence Limits (UCL95) and Compliance Decision Rules 5.3 Epidemiological Study Designs and Measures of Association 5.4 Sampling Strategy: Sample Size, Power, and Worker Selection

6 Chapter 6: Toxicology & Biological Monitoring

6.1 Dose-Response Relationships and Points of Departure 6.2 Toxicokinetics: Absorption, Distribution, Metabolism, and Elimination 6.3 Aerosol Deposition, Clearance, and Respiratory Tract Dosimetry 6.4 Hepatic, Renal, Neurologic, and Hematologic Target Organ Toxicity 6.5 Pulmonary Toxicology, Carcinogenicity, and Reproductive Hazards 6.6 OEL Frameworks, Classifications, and Excursion Limits 6.7 Chemical Mixtures and Extended Work-Shift OEL Adjustments 6.8 Biological Exposure Indices (BEIs) and Biomonitoring

7 Chapter 7: Biohazards & Indoor Environmental Quality

7.1 Mold, Fungi, and Microbial Contaminants 7.2 Infectious Agents, Bloodborne Pathogens, and Biosafety Levels 7.3 Indoor Environmental Quality (IEQ) Investigations 7.4 Sanitation, Potable Water, and Personal Hygiene Programs

8 Chapter 8: Community Exposure & Environmental Health

8.1 Clean Air Act Framework, NAAQS, and New Source Review 8.2 Hazardous Air Pollutants, CEMS, and EPA Reference Methods 8.3 Atmospheric Stability, Lapse Rates, and Plume Morphology 8.4 Gaussian Plume Modeling, Plume Rise, and Environmental Fate 8.5 HAZWOPER Scope, Mandates, and Training Tiers 8.6 Protection Levels, Site Zoning, Incident Command, and Decontamination 8.7 Water Pollution, Hazardous Waste, and Community Right-to-Know

9 Chapter 9: Health Risk Analysis & Hazard Communication

9.1 GHS Hazard Classification: Health and Physical Hazard Criteria 9.2 GHS Labels, Safety Data Sheets, and Trade Secret Rules 9.3 The AIHA Exposure Assessment Strategy and Similar Exposure Groups 9.4 Qualitative Exposure Profiling and the AIHA Risk Matrix 9.5 Quantitative Health Risk Characterization: HQ, HI, and ELCR 9.6 NIOSH Occupational Exposure Banding 9.7 Risk Communication and Reporting to Affected Parties

10 Chapter 10: Industrial Ventilation Principles & LEV Design

10.1 Elimination, Substitution, Isolation, Containment, and Process Change 10.2 LEV Hood Taxonomy and Capture Velocity Selection 10.3 Hood Airflow Equations, Entry Losses, and Hood Static Pressure 10.4 Particulate Transport Aerodynamics and Duct Sizing 10.5 Duct Friction, Fitting Losses, and System Balancing 10.6 Fan Categories and Pressure Dynamics Across the Fan 10.7 System Curves, the Fan Laws, and Density Corrections

11 Chapter 11: General Ventilation, Air Cleaning & Diagnostics

11.1 Dilution Ventilation Principles and Steady-State Modeling 11.2 Transient Purging and Air Distribution Geometry 11.3 Particulate Air Cleaning: Cyclones, Baghouses, Scrubbers, and ESPs 11.4 Gaseous Emission Control and Air Cleaner Selection 11.5 Ventilation System Troubleshooting and Testing

12 Chapter 12: Noise Measurement & Hearing Conservation

12.1 Acoustic Physics and Decibel Mathematics 12.2 Sound Propagation, Octave Bands, and Frequency Weighting 12.3 Noise Dose Metrics and OSHA versus ACGIH Criteria 12.4 Exchange Rates, Extended Shifts, and Dosimetry Field Protocols 12.5 Engineering Noise Controls and Hearing Protector Attenuation 12.6 Hearing Conservation Programs and Standard Threshold Shifts 12.7 Hand-Arm and Whole-Body Vibration

13 Chapter 13: Thermal Stress Assessment & Control

13.1 Wet Bulb Globe Temperature (WBGT) and Heat Stress Indices 13.2 Heat-Related Disorders, Acclimatization, and Work/Rest Regimens 13.3 Cold Stress Evaluation and Wind Chill

14 Chapter 14: Ionizing Radiation Protection

14.1 Ionizing Radiation Physics and Radioactive Decay Kinetics 14.2 Radiation Units, Radiobiology, and Health Effects 14.3 ALARA, Stay-Time, and the Inverse Square Law 14.4 Shielding Physics, Material Selection, and Gamma Constants 14.5 Radiation Detection Instruments and Spectrometry 14.6 Personnel Dosimetry, Dose Limits, and Contamination Surveys

15 Chapter 15: Non-Ionizing Radiation & Laser Safety

15.1 The Non-Ionizing Spectrum and Static/ELF Field Exposures 15.2 Radiofrequency and Microwave Exposure: SAR, Standards, and Surveys 15.3 Ultraviolet, Visible, and Infrared Radiation Hazards 15.4 Laser Safety Classifications and Optical Density Calculations 15.5 Illumination, Lighting Design, and Visual Performance

16 Chapter 16: Non-Engineering Controls & Personal Protective Equipment

16.1 Respiratory Protection Programs and Assigned Protection Factors 16.2 Maximum Use Concentration, Oxygen Deficiency, and Breathing Air 16.3 Particulate Filters, Sorbent Cartridges, and Change Schedules 16.4 Respirator Fit Testing Protocols 16.5 Chemical Protective Clothing and Dermal Exposure Control

17 Chapter 17: Ergonomics & Workstation Design

17.1 Soft-Tissue Biomechanics and WMSD Pathophysiology 17.2 Ergonomic Risk Factors and Their Interaction Effects 17.3 The Revised NIOSH Lifting Equation 17.4 RULA, REBA, the Strain Index, and the ACGIH HAL TLV 17.5 Anthropometry and Workstation Geometry 17.6 VDT Workstations, Hand Tool Design, and Administrative Ergonomics

18 Chapter 18: Work Environments & Industrial Processes

18.1 Welding Fume Emissions, Metal Fume Fever, and Cr(VI)/Manganese Toxicology 18.2 Foundry Operations and Hot Work Fire Prevention 18.3 Vapor Degreasing, Pickling, Electroplating, and Cyanide Baths 18.4 Spray Coatings, Isocyanates, and Semiconductor Manufacturing 18.5 Confined Spaces and High-Hazard Industrial Operations 18.6 Asbestos, Lead, and Silica: Regulated Substance Programs 18.7 Abrasive Blasting and Surface Preparation

19 Chapter 19: IH Program Management & Professional Ethics

19.1 The BGC Code of Ethics: Canons and Enforcement 19.2 Professional Liability, Standard of Care, and Expert Testimony 19.3 Occupational Health & Safety Management Systems (ISO 45001, ANSI Z10) 19.4 Exposure Records Access and Medical Surveillance 19.5 OSHA Injury and Illness Recordkeeping and Enforcement

15.5 Illumination, Lighting Design, and Visual Performance

Key Takeaways Explain This Topic AI

The four photometric quantities are luminous flux (lumen), luminous intensity (candela), illuminance (lux or foot-candle), and luminance (candela per square metre).

One foot-candle equals approximately 10.76 lux, and illuminance from a point source falls with the inverse square of distance.

OSHA 29 CFR 1926.56 sets minimum construction illumination of 5 foot-candles for general construction areas, 3 for concrete placement and excavation, 10 for construction plants and shops, and 30 for first-aid stations, infirmaries, and offices.

Glare is classified as disability glare, which measurably reduces visual performance, and discomfort glare, which causes strain without necessarily impairing acuity.

Discharge lamps operating on alternating current can produce a stroboscopic effect that makes rotating machinery appear stationary, which is a machine-guarding hazard.

Last updated: August 2026

Illumination, Lighting Design, and Visual Performance

The BGC subject area definition for non-ionizing radiation ends with "ultraviolet, visible, infrared radiation, and illumination ." Lighting is the only physical agent in industrial hygiene where the goal is not to minimise exposure but to optimise it: too little light and too much light both degrade performance, and glare degrades it at any level.

1. The Four Photometric Quantities

Confusing these is the most common source of lost points on lighting items.

  • Quantity Symbol SI unit Imperial What it describes
  • Luminous flux Φ lumen (lm) — Total light output of a source, in all directions
  • Luminous intensity I candela (cd) = lm/sr — Light emitted in a particular direction
  • Illuminance E lux (lx) = lm/m² foot-candle (fc) = lm/ft² Light arriving at a surface
  • Luminance L cd/m² foot-lambert Light leaving a surface toward the eye — what is actually seen as brightness

Two relationships you should be able to use without hesitation: 1 foot-candle = 10.76 lux ( 1 fc ≈ 10 lx for rough work ) 1\ \text{foot-candle} = 10.76\ \text{lux} \qquad (\text{1 fc} \approx 10\ \text{lx for rough work}) 1 foot-candle = 10.76 lux ( 1 fc ≈ 10 lx for rough work )

Illuminance is what a light meter measures at the task. Luminance is what determines perceived brightness and glare, and it depends on both the illuminance and the reflectance of the surface: L ≈ E × ρ π (for a diffuse surface, ρ = reflectance) L \approx \frac{E \times \rho}{\pi} \quad \text{(for a diffuse surface, } \rho = \text{reflectance)} L ≈ π E × ρ ​ (for a diffuse surface, ρ = reflectance)

A dark surface at high illuminance can have lower luminance than a light surface at modest illuminance, which is why raising lamp output is often the wrong fix for a task that is hard to see.

The inverse square and cosine laws

For a point source, illuminance at a surface perpendicular to the beam is: E = I d 2 E = \frac{I}{d^2} E = d 2 I ​

and when the surface is tilted by angle θ from the perpendicular, the cosine law applies: E = I cos ⁡ θ d 2 E = \frac{I \cos\theta}{d^2} E = d 2 I cos θ ​

Worked example. A 2,000 cd luminaire is mounted 4.0 m directly above a workbench. Illuminance at the bench directly below is E = 2,000 / 4.0² = 125 lux (about 11.6 fc). At a point 3.0 m horizontally from the centre, the distance is √(4² + 3²) = 5.0 m and cos θ = 4/5 = 0.8, giving E = 2,000 × 0.8 / 25 = 64 lux — roughly half, at only 3 m off-centre. This steep falloff is why luminaire spacing, not lamp wattage, governs uniformity.

2. Regulatory Minimums

OSHA's general industry standard sets illumination requirements only in specific contexts, but the construction standard 29 CFR 1926.56 sets explicit minimums that are directly testable:

  • Area Minimum illumination (foot-candles)
  • General construction area lighting 5

Concrete placement, excavation and waste areas, access ways, active storage areas, loading platforms, refuelling, field maintenance 3

Indoors: warehouses, corridors, hallways, exitways 5

Tunnels, shafts, and general underground work areas 5 (10 at tunnel and shaft headings during drilling, mucking, and scaling)

  • General construction plant and shops 10
  • First-aid stations, infirmaries, and offices 30

These are floors for safe movement and basic work , not design targets. The Illuminating Engineering Society (IES) recommended practice provides task-based design values that are much higher — typical office work in the range of 30 to 50 fc (300 to 500 lux), and fine assembly, inspection, or detailed drafting work substantially higher still. Design values increase with task difficulty, with reduced contrast, and with worker age, since the ageing eye transmits less light and scatters more.

3. Contrast, Luminance Ratios, and Visual Performance

Visual performance depends on four factors: task size, contrast, luminance, and exposure time . Increasing illuminance helps only until contrast becomes the limiting factor — after which adding light adds glare without adding performance.

Recommended maximum luminance ratios:

  • Comparison Ratio
  • Task to adjacent surroundings 3 : 1
  • Task to remote surfaces 10 : 1
  • Anywhere within the normal field of view 20 : 1
  • Luminaire or window to adjacent surface 40 : 1

Exceeding these forces continual adaptation as the eye moves, which is experienced as fatigue.

4. Glare

Type Definition Consequence Control

Disability glare Stray light scattered in the eye reduces retinal contrast Measurable loss of visual performance Shield or relocate the source; increase background luminance

Discomfort glare Excessive luminance in the field of view Strain, fatigue, complaints, without necessarily reduced acuity Lower luminaire luminance, raise mounting height, use diffusers and louvres

Reflected (veiling) glare Specular reflection of a bright source from the task surface Washes out contrast on the task itself Change the geometry so the reflection is not in the line of sight; use matte finishes

The controlling insight for reflected glare is that it is a geometry problem , not a brightness problem. If the luminaire, the task surface, and the eye form the specular angle, no amount of dimming or brightening fixes it — the geometry must change.

5. Colour and Flicker

Correlated colour temperature (CCT) , in kelvin, describes the appearance of the light: lower values (2,700–3,000 K) look warm, higher values (4,000–6,500 K) look cool or daylight-like.

Colour rendering index (CRI) , on a scale to 100, describes how faithfully surface colours appear under the source. High CRI is a safety requirement , not an aesthetic preference, wherever colour coding carries information — electrical wiring, gas cylinders, pipe marking, chemical labels, and product inspection. A low-CRI source such as low-pressure sodium renders colour so poorly that colour-coded systems become unreadable.

Flicker and the stroboscopic effect. Discharge lamps operating on alternating current modulate at twice the supply frequency. Where the modulation frequency is a multiple of the rotational speed of machinery, a rotating part can appear stationary or slowly rotating — a genuine machine-guarding hazard around lathes, saws, fans, and drive shafts. Controls include high-frequency electronic ballasts, distributing luminaires across different phases of a three-phase supply, and supplementing with incandescent or LED sources with low flicker. Perceptible flicker is also associated with headache, eyestrain, and, at some frequencies, photosensitive seizure risk.

6. Measurement

Illuminance is measured with a photometer that is both cosine corrected (so light arriving at oblique angles is weighted correctly) and colour corrected (so its spectral response matches the photopic response of the human eye). An uncorrected sensor can be badly wrong under sources with unusual spectra.

Survey practice:

Allow discharge lamps to stabilise — typically 15 to 20 minutes.

Measure at the task plane and in the task orientation , not at the floor and not horizontally when the task is vertical.

Take a grid of readings to characterise uniformity , not a single reading; the average conceals dark spots that determine where work is actually difficult.

Shield the sensor from the operator's own shadow and body reflectance.

Record lamp type, age, and cleanliness. Lumen depreciation and dirt accumulation can reduce delivered illuminance by 30% or more over a maintenance cycle, and a cleaning and relamping schedule is frequently a cheaper fix than new luminaires.