Study guide

13.1 Wet Bulb Globe Temperature (WBGT) and Heat Stress Indices

CIH Certified Industrial Hygienist Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: The CIH Exam and How to Use This Guide

1.1 CIH Exam Format, Scoring, and Test-Day Logistics 1.2 Eligibility, Application Windows, Fees, and Certification Maintenance 1.3 The BGC Blueprint, Subject Areas, and a Calculation-First Study Plan

2 Chapter 2: Basic Science & Calculations

2.1 Gas Laws and Vapor Calculations 2.2 Unit Conversions: ppm, mg/m³, and Standard Temperature/Pressure 2.3 Fluid Mechanics and Airflow Fundamentals

3 Chapter 3: Air Sampling & Instrumentation

3.1 Active and Passive Air Sampling Strategies 3.2 Particulate and Aerosol Sampling 3.3 Direct-Reading Instruments and Calibration

4 Chapter 4: Analytical Chemistry & Lab Methods

4.1 Gas Chromatography and Mass Spectrometry 4.2 High-Performance Liquid Chromatography and Ion Chromatography 4.3 Spectroscopy and Elemental Analysis 4.4 Gravimetric, Microscopy, and Wet Chemical Methods 4.5 Laboratory Quality Assurance, Chain of Custody, and Desorption Efficiency

5 Chapter 5: Biostatistics & Epidemiology

5.1 Lognormal Distributions and Exposure Data Statistics 5.2 Upper Confidence Limits (UCL95) and Compliance Decision Rules 5.3 Epidemiological Study Designs and Measures of Association 5.4 Sampling Strategy: Sample Size, Power, and Worker Selection

6 Chapter 6: Toxicology & Biological Monitoring

6.1 Dose-Response Relationships and Points of Departure 6.2 Toxicokinetics: Absorption, Distribution, Metabolism, and Elimination 6.3 Aerosol Deposition, Clearance, and Respiratory Tract Dosimetry 6.4 Hepatic, Renal, Neurologic, and Hematologic Target Organ Toxicity 6.5 Pulmonary Toxicology, Carcinogenicity, and Reproductive Hazards 6.6 OEL Frameworks, Classifications, and Excursion Limits 6.7 Chemical Mixtures and Extended Work-Shift OEL Adjustments 6.8 Biological Exposure Indices (BEIs) and Biomonitoring

7 Chapter 7: Biohazards & Indoor Environmental Quality

7.1 Mold, Fungi, and Microbial Contaminants 7.2 Infectious Agents, Bloodborne Pathogens, and Biosafety Levels 7.3 Indoor Environmental Quality (IEQ) Investigations 7.4 Sanitation, Potable Water, and Personal Hygiene Programs

8 Chapter 8: Community Exposure & Environmental Health

8.1 Clean Air Act Framework, NAAQS, and New Source Review 8.2 Hazardous Air Pollutants, CEMS, and EPA Reference Methods 8.3 Atmospheric Stability, Lapse Rates, and Plume Morphology 8.4 Gaussian Plume Modeling, Plume Rise, and Environmental Fate 8.5 HAZWOPER Scope, Mandates, and Training Tiers 8.6 Protection Levels, Site Zoning, Incident Command, and Decontamination 8.7 Water Pollution, Hazardous Waste, and Community Right-to-Know

9 Chapter 9: Health Risk Analysis & Hazard Communication

9.1 GHS Hazard Classification: Health and Physical Hazard Criteria 9.2 GHS Labels, Safety Data Sheets, and Trade Secret Rules 9.3 The AIHA Exposure Assessment Strategy and Similar Exposure Groups 9.4 Qualitative Exposure Profiling and the AIHA Risk Matrix 9.5 Quantitative Health Risk Characterization: HQ, HI, and ELCR 9.6 NIOSH Occupational Exposure Banding 9.7 Risk Communication and Reporting to Affected Parties

10 Chapter 10: Industrial Ventilation Principles & LEV Design

10.1 Elimination, Substitution, Isolation, Containment, and Process Change 10.2 LEV Hood Taxonomy and Capture Velocity Selection 10.3 Hood Airflow Equations, Entry Losses, and Hood Static Pressure 10.4 Particulate Transport Aerodynamics and Duct Sizing 10.5 Duct Friction, Fitting Losses, and System Balancing 10.6 Fan Categories and Pressure Dynamics Across the Fan 10.7 System Curves, the Fan Laws, and Density Corrections

11 Chapter 11: General Ventilation, Air Cleaning & Diagnostics

11.1 Dilution Ventilation Principles and Steady-State Modeling 11.2 Transient Purging and Air Distribution Geometry 11.3 Particulate Air Cleaning: Cyclones, Baghouses, Scrubbers, and ESPs 11.4 Gaseous Emission Control and Air Cleaner Selection 11.5 Ventilation System Troubleshooting and Testing

12 Chapter 12: Noise Measurement & Hearing Conservation

12.1 Acoustic Physics and Decibel Mathematics 12.2 Sound Propagation, Octave Bands, and Frequency Weighting 12.3 Noise Dose Metrics and OSHA versus ACGIH Criteria 12.4 Exchange Rates, Extended Shifts, and Dosimetry Field Protocols 12.5 Engineering Noise Controls and Hearing Protector Attenuation 12.6 Hearing Conservation Programs and Standard Threshold Shifts 12.7 Hand-Arm and Whole-Body Vibration

13 Chapter 13: Thermal Stress Assessment & Control

13.1 Wet Bulb Globe Temperature (WBGT) and Heat Stress Indices 13.2 Heat-Related Disorders, Acclimatization, and Work/Rest Regimens 13.3 Cold Stress Evaluation and Wind Chill

14 Chapter 14: Ionizing Radiation Protection

14.1 Ionizing Radiation Physics and Radioactive Decay Kinetics 14.2 Radiation Units, Radiobiology, and Health Effects 14.3 ALARA, Stay-Time, and the Inverse Square Law 14.4 Shielding Physics, Material Selection, and Gamma Constants 14.5 Radiation Detection Instruments and Spectrometry 14.6 Personnel Dosimetry, Dose Limits, and Contamination Surveys

15 Chapter 15: Non-Ionizing Radiation & Laser Safety

15.1 The Non-Ionizing Spectrum and Static/ELF Field Exposures 15.2 Radiofrequency and Microwave Exposure: SAR, Standards, and Surveys 15.3 Ultraviolet, Visible, and Infrared Radiation Hazards 15.4 Laser Safety Classifications and Optical Density Calculations 15.5 Illumination, Lighting Design, and Visual Performance

16 Chapter 16: Non-Engineering Controls & Personal Protective Equipment

16.1 Respiratory Protection Programs and Assigned Protection Factors 16.2 Maximum Use Concentration, Oxygen Deficiency, and Breathing Air 16.3 Particulate Filters, Sorbent Cartridges, and Change Schedules 16.4 Respirator Fit Testing Protocols 16.5 Chemical Protective Clothing and Dermal Exposure Control

17 Chapter 17: Ergonomics & Workstation Design

17.1 Soft-Tissue Biomechanics and WMSD Pathophysiology 17.2 Ergonomic Risk Factors and Their Interaction Effects 17.3 The Revised NIOSH Lifting Equation 17.4 RULA, REBA, the Strain Index, and the ACGIH HAL TLV 17.5 Anthropometry and Workstation Geometry 17.6 VDT Workstations, Hand Tool Design, and Administrative Ergonomics

18 Chapter 18: Work Environments & Industrial Processes

18.1 Welding Fume Emissions, Metal Fume Fever, and Cr(VI)/Manganese Toxicology 18.2 Foundry Operations and Hot Work Fire Prevention 18.3 Vapor Degreasing, Pickling, Electroplating, and Cyanide Baths 18.4 Spray Coatings, Isocyanates, and Semiconductor Manufacturing 18.5 Confined Spaces and High-Hazard Industrial Operations 18.6 Asbestos, Lead, and Silica: Regulated Substance Programs 18.7 Abrasive Blasting and Surface Preparation

19 Chapter 19: IH Program Management & Professional Ethics

19.1 The BGC Code of Ethics: Canons and Enforcement 19.2 Professional Liability, Standard of Care, and Expert Testimony 19.3 Occupational Health & Safety Management Systems (ISO 45001, ANSI Z10) 19.4 Exposure Records Access and Medical Surveillance 19.5 OSHA Injury and Illness Recordkeeping and Enforcement

13.1 Wet Bulb Globe Temperature (WBGT) and Heat Stress Indices

Key Takeaways Explain This Topic AI

The fundamental human heat balance equation is S = (M - W) ± C ± R ± K - E, where maintaining thermal equilibrium requires heat storage S = 0.

Wet Bulb Globe Temperature (WBGT) incorporates Natural Wet Bulb (NWB, 70% weighting), 6-inch Vernon Globe Thermometer (GT, 20-30 min stabilization), and shielded Dry Bulb (DB) temperatures.

WBGT formulas are WBGT_in = 0.7 NWB + 0.3 GT (indoor/no solar load) and WBGT_out = 0.7 NWB + 0.2 GT + 0.1 DB (outdoor with direct solar load).

ACGIH Clothing Adjustment Factors (CAF) must be added to measured WBGT (WBGT_eff = WBGT_meas + CAF), ranging from +0°C for standard cotton uniforms to +3.0°C for vapor-barrier coveralls and +10.0°C for unventilated Level A encapsulating suits.

ACGIH Heat Stress TLVs and Action Levels define environmental exposure limits across metabolic rates: Light (180 W), Moderate (300 W), Heavy (415 W), and Very Heavy (520 W).

Last updated: August 2026

Wet Bulb Globe Temperature (WBGT) and Heat Stress Indices

Occupational exposure to thermal extremes represents one of the most physically demanding challenges evaluated by Certified Industrial Hygienists. Heat stress refers to the total net heat load to which a worker is exposed from the combined contributions of metabolic heat production , environmental factors (ambient air temperature, humidity, air velocity, and radiant heat), and clothing barriers . In contrast, heat strain represents the physiological response of the human body to this net heat load (e.g., elevation in core body temperature, sweat production, and elevated heart rate). This section explores the thermodynamic physics of human heat exchange, the Wet Bulb Globe Temperature (WBGT) index, Clothing Adjustment Factors (CAF), and the ACGIH Threshold Limit Values (TLVs) and Action Levels (ALs).

1. Thermodynamic Physics of Human Heat Exchange

The human body operates as an open thermodynamic system that must maintain its deep core temperature within a narrow physiological window (37.0°C ± 0.5°C or 98.6°F ± 0.9°F) to sustain enzymatic activity and central nervous system function. The net exchange of thermal energy between the worker and the environment is governed by the classical Heat Balance Equation : S = ( M − W ) ± C ± R ± K − E S = (M - W) \pm C \pm R \pm K - E S = ( M − W ) ± C ± R ± K − E

Where:

  • S = Rate of heat storage (accumulation or deficit of heat in the body core and shell, W or kcal/h)
  • M = Rate of metabolic heat production generated by internal biochemical oxidation (W or kcal/h)
  • W = Rate of external mechanical work performed by the body on the surroundings (W or kcal/h)
  • C = Rate of convective heat exchange between the skin/clothing and surrounding air (W or kcal/h)
  • R = Rate of radiant heat exchange between the body and surrounding solid surfaces/sun (W or kcal/h)
  • K = Rate of conductive heat exchange via direct physical contact with solids/liquids (W or kcal/h)
  • E = Rate of evaporative heat loss from sweat vaporization and respiratory tract moisture (W or kcal/h)
  • Condition for Thermal Homeostasis

When S = 0 , the body is in steady-state thermal equilibrium, and core body temperature remains constant. If S > 0 , heat storage is positive, causing core body temperature to rise toward dangerous hyperthermic thresholds. If S < 0 , the body loses more heat than it produces, leading toward hypothermia. +--------------------------------------------------------------------------+

  • | HUMAN HEAT BALANCE EQUATION |
  • | |
  • | S = (M - W) ± C ± R ± K - E |
  • | [Net] [Metabolic] [Convect] [Radiant] [Conduct] [Evaporative] |
  • | |
  • | • S = 0 --> Thermal Equilibrium (Constant Core Temperature) |
  • | • S > 0 --> Heat Storage / Hyperthermia Risk (Core Temp Rises) |
  • | • S < 0 --> Heat Deficit / Hypothermia Risk (Core Temp Drops) |
  • +--------------------------------------------------------------------------+
  • Breakdown of Heat Exchange Mechanisms

Metabolic Heat Generation (M - W): Metabolic reactions convert chemical energy from food into mechanical work (W) and thermal energy (M). Because human mechanical muscular efficiency is relatively low (typically 15% to 20%, meaning 80% to 85% of expended energy is degraded directly into heat), the net metabolic heat load is large. In industrial hygiene assessments, external work (W) is frequently assumed to be zero (W = 0) as a conservative safety measure, so net metabolic heat equals M.

Convection (C): Convective heat transfer occurs through fluid movement (air or water) across the skin or clothing boundary layer. It is driven by the temperature gradient between ambient air (Ta) and mean skin temperature (Tsk ≈ 35.0°C or 95.0°F), as well as air velocity (v): C = h c ( T a − T sk ) C = h_c (T_a - T_{\text{sk}}) C = h c ​ ( T a ​ − T sk ​ )

If Ta < Tsk: Heat is lost from the body to the air (-C).

If Ta > Tsk: Heat is transferred from the air into the body (+C), adding to the thermal burden. Increasing air velocity when air temperature exceeds skin temperature increases convective heat gain.

Radiation (R): Radiant heat exchange involves electromagnetic infrared radiation between the body surface and surrounding solid surfaces (furnace walls, hot pipes, molten metal, sun, sky). Governed by the Stefan-Boltzmann law, linearized radiant exchange is proportional to the difference between Mean Radiant Temperature (T̄mrt) and skin temperature (Tsk): R = h r ( T ˉ mrt − T sk ) R = h_r (\bar{T}_{\text{mrt}} - T_{\text{sk}}) R = h r ​ ( T ˉ mrt ​ − T sk ​ )

If T̄mrt > Tsk: The worker absorbs radiant heat (+R), regardless of ambient air temperature.

Conduction (K): Conductive transfer occurs through direct physical contact with solids (e.g., sitting on hot metal flooring, handling cold or heated tools). In most industrial settings, conductive exchange through the soles of shoes is negligible (K ≈ 0) unless workers kneel, lie down, or immerse limbs in liquids.

Evaporation (E): Evaporative heat loss is the body's primary physiological defense against hyperthermia. Evaporating water from the skin requires latent heat of vaporization (approximately 2,430 J/g or 580 kcal/L of sweat). Evaporative heat loss (E) depends on the water vapor pressure gradient between saturated skin (Psk ≈ 42 mmHg at 35°C) and ambient air (Pa), as well as air velocity and clothing vapor permeability: E max = h e ( P sk − P a ) E_{\text{max}} = h_e (P_{\text{sk}} - P_a) E max ​ = h e ​ ( P sk ​ − P a ​ )

Critical Principle: When ambient air temperature exceeds skin temperature (Ta > 35.0°C), both convection (+C) and radiation (+R) add heat to the body. Under these conditions, evaporative cooling (-E) is the sole physiological mechanism available to dissipate body heat . If relative humidity reaches 100% (Pa = Psk), Emax drops to zero, and thermal storage (S > 0) escalates rapidly.

2. Wet Bulb Globe Temperature (WBGT) Instrumentation

The Wet Bulb Globe Temperature (WBGT) index is the globally accepted standard for occupational heat stress screening (standardized under ISO 7243, ACGIH TLVs, and OSHA guidelines). WBGT integrates the four environmental parameters—air temperature, radiant heat, humidity, and air velocity—into a single numeric value using three primary sensors. +--------------------------------------------------------------------------+

  • | WBGT SENSOR CONFIGURATION |
  • | |
  • | [ Natural Wet Bulb ] [ Globe Thermometer ] [ Dry Bulb ] |
  • | (NWB / T_nwb) (GT / T_g) (DB / T_a) |
  • | |
  • | • 100% clean cotton wick • 15 cm (6-inch) copper • Shielded |
  • | • Distilled water wick sphere painted matte from radiant|
  • | • Unshielded, natural air black (emissivity 0.95) heat/sun |
  • | • Measures evaporative • Requires 20-30 min • Measures air|
  • | cooling & humidity thermal equilibrium temperature |
  • +--------------------------------------------------------------------------+
  • The Three Component Sensors

Sensor Designation Physical Construction & Operating Principle Primary Parameter Measured

Natural Wet Bulb NWB or Tnwb A precision temperature sensor encased in a clean, wetted 100% cotton wick immersed in a distilled water reservoir. It is unshielded from radiant heat and aspirated solely by natural ambient airflow (distinct from a psychrometer's forced-air wet bulb). Combined evaporative cooling potential, air velocity, and ambient humidity

Vernon Globe Thermometer GT or Tg A 15 cm (6-inch) diameter hollow copper sphere painted with matte black paint (absorptance/emissivity ≈ 0.95), containing a temperature sensor at its geometric center. Requires 20 to 30 minutes to reach thermodynamic equilibrium. Integrated radiant heat load from solar/infrared sources and convective air cooling

Dry Bulb DB or Ta A precision temperature sensor shielded from direct solar radiation and surrounding radiant sources by a reflective, open-ventilated radiation shield. True ambient dry-bulb air temperature

3. WBGT Mathematical Formulations

Depending on the presence of direct solar radiation, two distinct empirical equations are utilized:

1. Indoor Environments or Outdoor Environments Without Direct Solar Load

Used inside buildings, within covered structures, or outdoors at night/under complete cloud cover with zero direct solar load: WBGT in = 0.7 N W B + 0.3 G T \mathbf{\text{WBGT}_{\text{in}} = 0.7\,NWB + 0.3\,GT} WBGT in ​ = 0.7 NWB + 0.3 GT

Weighting Rationale: Ambient humidity and evaporative cooling potential (NWB) govern 70% of the index, while radiant heating and convection (GT) account for the remaining 30%.

2. Outdoor Environments With Direct Solar Load

Used for outdoor work under direct sunlight where solar radiation imposes an additional radiant burden: WBGT out = 0.7 N W B + 0.2 G T + 0.1 D B \mathbf{\text{WBGT}_{\text{out}} = 0.7\,NWB + 0.2\,GT + 0.1\,DB} WBGT out ​ = 0.7 NWB + 0.2 GT + 0.1 DB

Weighting Rationale: Direct solar radiation requires explicit inclusion of the ambient dry-bulb air temperature (10% weighting) to decouple solar irradiance from the globe thermometer (20% weighting), while natural wet bulb maintains its 70% dominance.

4. Clothing Adjustment Factors (CAF)

The standard ACGIH Heat Stress TLV curves are calibrated for healthy, acclimatized workers wearing standard lightweight cotton work clothing (long-sleeve cotton work shirt and trousers, thermal resistance ≈ 0.6 clo). Specialized protective ensembles restrict evaporative sweat dissipation and trap metabolic heat. To evaluate heat stress for workers wearing non-standard clothing, an empirical Clothing Adjustment Factor (CAF) is added directly to the measured environmental WBGT: WBGT eff = WBGT measured + CAF \mathbf{\text{WBGT}_{\text{eff}} = \text{WBGT}_{\text{measured}} + \text{CAF}} WBGT eff ​ = WBGT measured ​ + CAF

ACGIH Clothing Adjustment Factor Values

  • Clothing Type / Ensemble Description & Fabric Characteristics CAF (°C) CAF (°F)
  • Standard Work Clothes Lightweight long-sleeve cotton shirt and long trousers +0.0°C +0.0°F
  • SMS Polypropylene Coveralls Spunbond-meltblown-spunbond breathable particulate coveralls +0.5°C +0.9°F
  • Polyolefin Coveralls Microporous barrier non-woven protective coveralls +1.0°C +1.8°F

Double-Layer Woven Clothing Two layers of standard cloth (e.g., cotton coveralls over work uniform) +2.0°C +3.6°F

Vapor-Barrier Coveralls Impermeable chemical suits (e.g., Tychem, PVC, butyl rubber, coated fabrics) +3.0°C +5.4°F

Unventilated Level A Suits Fully encapsulating, gastight chemical protective ensembles +10.0°C +18.0°F

Critical Compliance Rule: When workers wear vapor-barrier, encapsulating, or Level A protective suits, the evaporative heat transfer coefficient drops near zero (E ≈ 0). In such cases, the WBGT screening index is not reliable for ensuring safety, and direct physiological monitoring (continuous core temperature and recovery heart rate tracking) is mandatory.

5. ACGIH Heat Stress TLVs and Action Levels

The American Conference of Governmental Industrial Hygienists (ACGIH) establishes Threshold Limit Values (TLVs) for acclimatized workers and Action Levels (ALs) for unacclimatized workers. These criteria are based on maintaining core body temperature at or below 38.0°C (100.4°F) for unacclimatized workers and 38.5°C (101.3°F) for acclimatized workers.

Metabolic Work Rate Categories

  • Category Metabolic Rate (M) Typical Industrial Tasks
  • Rest < 115 W (< 100 kcal/h) Sitting quietly, desk work, light administrative supervision

Light 180 W (115--230 W) Sitting or standing while operating machinery, light bench assembly, precision electronic assembly, driving

Moderate 300 W (230--350 W) Sustained walking, lifting 10--15 kg intermittently, pushing carts, bricklaying, weed eating, scrubbing

Heavy 415 W (350--480 W) Shoveling dry soil, manual sawing, carrying heavy pipe, continuous sledgehammer work, pushing wheelbarrows

Very Heavy 520 W (> 480 W) Shoveling wet sand/concrete, rapid stair climbing with heavy packs, intense manual ditch digging

ACGIH WBGT Screening Criteria (°C)

Work Allocation (% Work / % Rest) Light (180 W) [TLV / AL] Moderate (300 W) [TLV / AL] Heavy (415 W) [TLV / AL] Very Heavy (520 W) [TLV / AL]

  • 75% to 100% (Continuous) 31.0°C / 28.0°C 28.0°C / 25.0°C 26.0°C / 23.0°C 25.0°C / 22.5°C
  • 50% to 75% (75% Work / 25% Rest) 31.5°C / 28.5°C 29.0°C / 26.0°C 27.5°C / 24.5°C 26.0°C / 23.5°C
  • 25% to 50% (50% Work / 50% Rest) 32.0°C / 29.5°C 30.0°C / 27.0°C 28.5°C / 25.5°C 27.5°C / 25.0°C
  • 0% to 25% (25% Work / 75% Rest) 32.5°C / 30.0°C 31.0°C / 28.5°C 30.0°C / 27.5°C 29.5°C / 27.0°C
  • 6. Time-Weighted Average (TWA) Calculations

Workers frequently move between different thermal microenvironments or cycle between varying physical exertion levels throughout their shifts. To evaluate compliance, Time-Weighted Average WBGT (WBGTTWA) and Time-Weighted Average Metabolic Rate (MTWA) are calculated over representative 60 to 120-minute work periods: WBGT TWA = ∑ i = 1 n ( WBGT i × t i ) ∑ i = 1 n t i = WBGT 1 t 1 + WBGT 2 t 2 + ⋯ + WBGT n t n t 1 + t 2 + ⋯ + t n \mathbf{\text{WBGT}_{\text{TWA}} = \frac{\sum_{i=1}^n (\text{WBGT}_i \times t_i)}{\sum_{i=1}^n t_i} = \frac{\text{WBGT}_1 t_1 + \text{WBGT}_2 t_2 + \dots + \text{WBGT}_n t_n}{t_1 + t_2 + \dots + t_n}} WBGT TWA ​ = ∑ i = 1 n ​ t i ​ ∑ i = 1 n ​ ( WBGT i ​ × t i ​ ) ​ = t 1 ​ + t 2 ​ + ⋯ + t n ​ WBGT 1 ​ t 1 ​ + WBGT 2 ​ t 2 ​ + ⋯ + WBGT n ​ t n ​ ​ M TWA = ∑ i = 1 n ( M i × t i ) ∑ i = 1 n t i = M 1 t 1 + M 2 t 2 + ⋯ + M n t n t 1 + t 2 + ⋯ + t n \mathbf{M_{\text{TWA}} = \frac{\sum_{i=1}^n (M_i \times t_i)}{\sum_{i=1}^n t_i} = \frac{M_1 t_1 + M_2 t_2 + \dots + M_n t_n}{t_1 + t_2 + \dots + t_n}} M TWA ​ = ∑ i = 1 n ​ t i ​ ∑ i = 1 n ​ ( M i ​ × t i ​ ) ​ = t 1 ​ + t 2 ​ + ⋯ + t n ​ M 1 ​ t 1 ​ + M 2 ​ t 2 ​ + ⋯ + M n ​ t n ​ ​

  • 7. Worked Step-by-Step Calculation Examples
  • Worked Example 12.1: Indoor vs. Outdoor WBGT and Clothing Adjustment

Scenario: An industrial hygienist conducts heat stress monitoring at a hazardous materials remediation site. Environmental measurements outdoors under direct midday solar load reveal:

  • Natural Wet Bulb (NWB) = 27.0°C
  • Vernon Globe Temperature (GT) = 42.0°C
  • Shielded Dry Bulb (DB) = 34.0°C

The remediation workers wear polyolefin microporous coveralls (CAF = +1.0°C) while performing moderate work (M = 300 W). The crew consists of acclimatized workers performing continuous work.

Calculate the environmental outdoor WBGT (WBGTout).

Calculate the effective WBGT (WBGTeff) accounting for the protective clothing.

Determine whether the exposure exceeds the ACGIH TLV for continuous moderate work (28.0°C).

Solution Steps:

Calculate Environmental WBGTout: WBGT out = 0.7 N W B + 0.2 G T + 0.1 D B \text{WBGT}_{\text{out}} = 0.7\,NWB + 0.2\,GT + 0.1\,DB WBGT out ​ = 0.7 N W B + 0.2 GT + 0.1 D B WBGT out = ( 0.7 × 27.0 ) + ( 0.2 × 42.0 ) + ( 0.1 × 34.0 ) \text{WBGT}_{\text{out}} = (0.7 \times 27.0) + (0.2 \times 42.0) + (0.1 \times 34.0) WBGT out ​ = ( 0.7 × 27.0 ) + ( 0.2 × 42.0 ) + ( 0.1 × 34.0 ) WBGT out = 18.9 + 8.4 + 3.4 = 30.7 ∘ C \text{WBGT}_{\text{out}} = 18.9 + 8.4 + 3.4 = 30.7^\circ\text{C} WBGT out ​ = 18.9 + 8.4 + 3.4 = 30. 7 ∘ C

Apply Clothing Adjustment Factor (CAF): WBGT eff = WBGT out + CAF = 30.7 ∘ C + 1.0 ∘ C = 31.7 ∘ C \text{WBGT}_{\text{eff}} = \text{WBGT}_{\text{out}} + \text{CAF} = 30.7^\circ\text{C} + 1.0^\circ\text{C} = 31.7^\circ\text{C} WBGT eff ​ = WBGT out ​ + CAF = 30. 7 ∘ C + 1. 0 ∘ C = 31. 7 ∘ C

Compare Against ACGIH TLV:

The ACGIH TLV for continuous moderate work (300 W) is 28.0°C .

Since WBGTeff = 31.7°C > 28.0°C, the exposure substantially exceeds the TLV .

Recommendation: Implement an administrative work/rest regimen (e.g., 25% work / 75% rest, where the TLV is 31.0°C) or provide auxiliary body cooling vests.

Worked Example 12.2: Multi-Zone Time-Weighted Average (TWA) Calculation

Scenario: A boiler maintenance mechanic performs a cyclical 2-hour (120 min) maintenance task involving three distinct operational phases:

Phase 1 (Boiler Platform): 40 minutes inside a boiler house. WBGT1 = 33.0°C, performing heavy physical piping assembly (M1 = 415 W). The mechanic wears standard work clothing (CAF = 0.0°C).

Phase 2 (Control Room): 50 minutes in an air-conditioned control room logging telemetry. WBGT2 = 22.0°C, light sedentary activity (M2 = 180 W).

Phase 3 (Outdoor Tank Farm): 30 minutes walking inspection under direct solar load. WBGT3 = 29.0°C, moderate walking (M3 = 300 W).

Calculate the 2-hour Time-Weighted Average WBGT (WBGTTWA) and the Time-Weighted Average Metabolic Rate (MTWA).

Solution Steps:

Calculate Time-Weighted Average WBGT: WBGT TWA = ( WBGT 1 × t 1 ) + ( WBGT 2 × t 2 ) + ( WBGT 3 × t 3 ) t 1 + t 2 + t 3 \text{WBGT}_{\text{TWA}} = \frac{(\text{WBGT}_1 \times t_1) + (\text{WBGT}_2 \times t_2) + (\text{WBGT}_3 \times t_3)}{t_1 + t_2 + t_3} WBGT TWA ​ = t 1 ​ + t 2 ​ + t 3 ​ ( WBGT 1 ​ × t 1 ​ ) + ( WBGT 2 ​ × t 2 ​ ) + ( WBGT 3 ​ × t 3 ​ ) ​ WBGT TWA = ( 33.0 × 40 ) + ( 22.0 × 50 ) + ( 29.0 × 30 ) 40 + 50 + 30 \text{WBGT}_{\text{TWA}} = \frac{(33.0 \times 40) + (22.0 \times 50) + (29.0 \times 30)}{40 + 50 + 30} WBGT TWA ​ = 40 + 50 + 30 ( 33.0 × 40 ) + ( 22.0 × 50 ) + ( 29.0 × 30 ) ​ WBGT TWA = 1320 + 1100 + 870 120 = 3290 120 = 27.42 ∘ C \text{WBGT}_{\text{TWA}} = \frac{1320 + 1100 + 870}{120} = \frac{3290}{120} = 27.42^\circ\text{C} WBGT TWA ​ = 120 1320 + 1100 + 870 ​ = 120 3290 ​ = 27.4 2 ∘ C

Calculate Time-Weighted Average Metabolic Rate: M TWA = ( M 1 × t 1 ) + ( M 2 × t 2 ) + ( M 3 × t 3 ) t 1 + t 2 + t 3 M_{\text{TWA}} = \frac{(M_1 \times t_1) + (M_2 \times t_2) + (M_3 \times t_3)}{t_1 + t_2 + t_3} M TWA ​ = t 1 ​ + t 2 ​ + t 3 ​ ( M 1 ​ × t 1 ​ ) + ( M 2 ​ × t 2 ​ ) + ( M 3 ​ × t 3 ​ ) ​ M TWA = ( 415 × 40 ) + ( 180 × 50 ) + ( 300 × 30 ) 120 M_{\text{TWA}} = \frac{(415 \times 40) + (180 \times 50) + (300 \times 30)}{120} M TWA ​ = 120 ( 415 × 40 ) + ( 180 × 50 ) + ( 300 × 30 ) ​ M TWA = 16600 + 9000 + 9000 120 = 34600 120 = 288.33 W M_{\text{TWA}} = \frac{16600 + 9000 + 9000}{120} = \frac{34600}{120} = 288.33\text{ W} M TWA ​ = 120 16600 + 9000 + 9000 ​ = 120 34600 ​ = 288.33 W

Conclusion: The worker's average exposure is WBGTTWA = 27.4°C at an average metabolic rate of 288 W (Moderate) . For continuous work at this moderate rate, the acclimatized TLV is 28.0°C, meaning the overall 2-hour task cycle is within acceptable occupational limits.