Study guide

10.2 LEV Hood Taxonomy and Capture Velocity Selection

CIH Certified Industrial Hygienist Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: The CIH Exam and How to Use This Guide

1.1 CIH Exam Format, Scoring, and Test-Day Logistics 1.2 Eligibility, Application Windows, Fees, and Certification Maintenance 1.3 The BGC Blueprint, Subject Areas, and a Calculation-First Study Plan

2 Chapter 2: Basic Science & Calculations

2.1 Gas Laws and Vapor Calculations 2.2 Unit Conversions: ppm, mg/m³, and Standard Temperature/Pressure 2.3 Fluid Mechanics and Airflow Fundamentals

3 Chapter 3: Air Sampling & Instrumentation

3.1 Active and Passive Air Sampling Strategies 3.2 Particulate and Aerosol Sampling 3.3 Direct-Reading Instruments and Calibration

4 Chapter 4: Analytical Chemistry & Lab Methods

4.1 Gas Chromatography and Mass Spectrometry 4.2 High-Performance Liquid Chromatography and Ion Chromatography 4.3 Spectroscopy and Elemental Analysis 4.4 Gravimetric, Microscopy, and Wet Chemical Methods 4.5 Laboratory Quality Assurance, Chain of Custody, and Desorption Efficiency

5 Chapter 5: Biostatistics & Epidemiology

5.1 Lognormal Distributions and Exposure Data Statistics 5.2 Upper Confidence Limits (UCL95) and Compliance Decision Rules 5.3 Epidemiological Study Designs and Measures of Association 5.4 Sampling Strategy: Sample Size, Power, and Worker Selection

6 Chapter 6: Toxicology & Biological Monitoring

6.1 Dose-Response Relationships and Points of Departure 6.2 Toxicokinetics: Absorption, Distribution, Metabolism, and Elimination 6.3 Aerosol Deposition, Clearance, and Respiratory Tract Dosimetry 6.4 Hepatic, Renal, Neurologic, and Hematologic Target Organ Toxicity 6.5 Pulmonary Toxicology, Carcinogenicity, and Reproductive Hazards 6.6 OEL Frameworks, Classifications, and Excursion Limits 6.7 Chemical Mixtures and Extended Work-Shift OEL Adjustments 6.8 Biological Exposure Indices (BEIs) and Biomonitoring

7 Chapter 7: Biohazards & Indoor Environmental Quality

7.1 Mold, Fungi, and Microbial Contaminants 7.2 Infectious Agents, Bloodborne Pathogens, and Biosafety Levels 7.3 Indoor Environmental Quality (IEQ) Investigations 7.4 Sanitation, Potable Water, and Personal Hygiene Programs

8 Chapter 8: Community Exposure & Environmental Health

8.1 Clean Air Act Framework, NAAQS, and New Source Review 8.2 Hazardous Air Pollutants, CEMS, and EPA Reference Methods 8.3 Atmospheric Stability, Lapse Rates, and Plume Morphology 8.4 Gaussian Plume Modeling, Plume Rise, and Environmental Fate 8.5 HAZWOPER Scope, Mandates, and Training Tiers 8.6 Protection Levels, Site Zoning, Incident Command, and Decontamination 8.7 Water Pollution, Hazardous Waste, and Community Right-to-Know

9 Chapter 9: Health Risk Analysis & Hazard Communication

9.1 GHS Hazard Classification: Health and Physical Hazard Criteria 9.2 GHS Labels, Safety Data Sheets, and Trade Secret Rules 9.3 The AIHA Exposure Assessment Strategy and Similar Exposure Groups 9.4 Qualitative Exposure Profiling and the AIHA Risk Matrix 9.5 Quantitative Health Risk Characterization: HQ, HI, and ELCR 9.6 NIOSH Occupational Exposure Banding 9.7 Risk Communication and Reporting to Affected Parties

10 Chapter 10: Industrial Ventilation Principles & LEV Design

10.1 Elimination, Substitution, Isolation, Containment, and Process Change 10.2 LEV Hood Taxonomy and Capture Velocity Selection 10.3 Hood Airflow Equations, Entry Losses, and Hood Static Pressure 10.4 Particulate Transport Aerodynamics and Duct Sizing 10.5 Duct Friction, Fitting Losses, and System Balancing 10.6 Fan Categories and Pressure Dynamics Across the Fan 10.7 System Curves, the Fan Laws, and Density Corrections

11 Chapter 11: General Ventilation, Air Cleaning & Diagnostics

11.1 Dilution Ventilation Principles and Steady-State Modeling 11.2 Transient Purging and Air Distribution Geometry 11.3 Particulate Air Cleaning: Cyclones, Baghouses, Scrubbers, and ESPs 11.4 Gaseous Emission Control and Air Cleaner Selection 11.5 Ventilation System Troubleshooting and Testing

12 Chapter 12: Noise Measurement & Hearing Conservation

12.1 Acoustic Physics and Decibel Mathematics 12.2 Sound Propagation, Octave Bands, and Frequency Weighting 12.3 Noise Dose Metrics and OSHA versus ACGIH Criteria 12.4 Exchange Rates, Extended Shifts, and Dosimetry Field Protocols 12.5 Engineering Noise Controls and Hearing Protector Attenuation 12.6 Hearing Conservation Programs and Standard Threshold Shifts 12.7 Hand-Arm and Whole-Body Vibration

13 Chapter 13: Thermal Stress Assessment & Control

13.1 Wet Bulb Globe Temperature (WBGT) and Heat Stress Indices 13.2 Heat-Related Disorders, Acclimatization, and Work/Rest Regimens 13.3 Cold Stress Evaluation and Wind Chill

14 Chapter 14: Ionizing Radiation Protection

14.1 Ionizing Radiation Physics and Radioactive Decay Kinetics 14.2 Radiation Units, Radiobiology, and Health Effects 14.3 ALARA, Stay-Time, and the Inverse Square Law 14.4 Shielding Physics, Material Selection, and Gamma Constants 14.5 Radiation Detection Instruments and Spectrometry 14.6 Personnel Dosimetry, Dose Limits, and Contamination Surveys

15 Chapter 15: Non-Ionizing Radiation & Laser Safety

15.1 The Non-Ionizing Spectrum and Static/ELF Field Exposures 15.2 Radiofrequency and Microwave Exposure: SAR, Standards, and Surveys 15.3 Ultraviolet, Visible, and Infrared Radiation Hazards 15.4 Laser Safety Classifications and Optical Density Calculations 15.5 Illumination, Lighting Design, and Visual Performance

16 Chapter 16: Non-Engineering Controls & Personal Protective Equipment

16.1 Respiratory Protection Programs and Assigned Protection Factors 16.2 Maximum Use Concentration, Oxygen Deficiency, and Breathing Air 16.3 Particulate Filters, Sorbent Cartridges, and Change Schedules 16.4 Respirator Fit Testing Protocols 16.5 Chemical Protective Clothing and Dermal Exposure Control

17 Chapter 17: Ergonomics & Workstation Design

17.1 Soft-Tissue Biomechanics and WMSD Pathophysiology 17.2 Ergonomic Risk Factors and Their Interaction Effects 17.3 The Revised NIOSH Lifting Equation 17.4 RULA, REBA, the Strain Index, and the ACGIH HAL TLV 17.5 Anthropometry and Workstation Geometry 17.6 VDT Workstations, Hand Tool Design, and Administrative Ergonomics

18 Chapter 18: Work Environments & Industrial Processes

18.1 Welding Fume Emissions, Metal Fume Fever, and Cr(VI)/Manganese Toxicology 18.2 Foundry Operations and Hot Work Fire Prevention 18.3 Vapor Degreasing, Pickling, Electroplating, and Cyanide Baths 18.4 Spray Coatings, Isocyanates, and Semiconductor Manufacturing 18.5 Confined Spaces and High-Hazard Industrial Operations 18.6 Asbestos, Lead, and Silica: Regulated Substance Programs 18.7 Abrasive Blasting and Surface Preparation

19 Chapter 19: IH Program Management & Professional Ethics

19.1 The BGC Code of Ethics: Canons and Enforcement 19.2 Professional Liability, Standard of Care, and Expert Testimony 19.3 Occupational Health & Safety Management Systems (ISO 45001, ANSI Z10) 19.4 Exposure Records Access and Medical Surveillance 19.5 OSHA Injury and Illness Recordkeeping and Enforcement

10.2 LEV Hood Taxonomy and Capture Velocity Selection

Key Takeaways Explain This Topic AI

Air pulled into an exhaust opening is drawn from all directions, so centreline velocity falls to under 10% of face velocity within about one duct diameter; blowing jets carry ten times farther, which is why push-pull systems work.

Enclosing hoods are always preferred over capturing hoods, which are preferred over receiving hoods, because enclosure removes reliance on capture velocity entirely.

Capture velocity is selected from the contaminant release energy and the ambient air motion: roughly 50 to 100 fpm for release into quiet air, up to 2,000 fpm or more for release with high initial velocity into rapid air motion.

Capture velocity is the velocity at the point of contaminant generation, not at the hood face — confusing the two is the most common LEV design error.

Last updated: August 2026

LEV Hood Taxonomy and Capture Velocity Selection

Local Exhaust Ventilation ( LEV ) is the primary engineering control methodology utilized in industrial hygiene to capture airborne contaminants—including toxic dusts, metal fumes, mists, vapors, and gases—at or near their emission source before they disperse into the general workroom atmosphere and enter worker breathing zones. Unlike dilution ventilation, which merely dilutes already-dispersed airborne contaminants, a properly engineered LEV system captures contaminants at high localized concentrations using minimal air volumes, thereby optimizing worker protection, reducing capital HVAC energy costs, and minimizing air cleaning equipment sizing.

1. Aerodynamic Principles and Velocity Decay

The fundamental physical challenge of LEV hood design is governed by the laws of fluid dynamics: air under suction has virtually no directional momentum compared to air under positive pressure (blowing) . +-------------------------------------------------------------------------+

  • | SUCTION VELOCITY DECAY VS. BLOWING JETS |
  • +-------------------------------------------------------------------------+
  • | |
  • | BLOWING (Positive Jet): |
  • | Air pushed out of a duct forms a focused, high-velocity core jet. |
  • | Centerline velocity remains ~10% of duct face velocity at 30 Diameters!|
  • | |
  • | Duct =====> [ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> ] |
  • | 0D 10D 20D 30D |
  • | |
  • | SUCTION (Exhaust Hood): |
  • | Air pulled into an exhaust opening is drawn radially from ALL directions|
  • | (a spherical 360° intake field). Suction velocity decays precipitously!|
  • | Centerline velocity drops to < 10% of face velocity at just 1 Diameter!|
  • | |
  • | \ | / |
  • | \ v / |
  • | <==== [ DUCT ] <==== |
  • | / ^ \ |
  • | / | \ |
  • | x = 1D (Velocity <= 10% V_face) |
  • +-------------------------------------------------------------------------+

Because suction velocity decays inversely with the square of distance (x²) for point and round openings, hood placement close to the contaminant generation point is the single most critical determinant of LEV capture efficacy .

2. Comprehensive LEV Hood Taxonomy

Industrial exhaust hoods are categorized into three primary structural and aerodynamic classifications: Enclosing Hoods , Receiving Hoods , and Exterior Hoods . +-------------------------------------------------------------------------+

  • | CLASSIFICATION OF LEV HOODS |
  • +-------------------------------------------------------------------------+
  • | |
  • | 1. ENCLOSING HOODS |
  • | - Complete Enclosures: Gloveboxes, sealed abrasive blast cabinets |
  • | - Partial Enclosures: Laboratory chemical fume hoods, paint booths |
  • | |
  • | 2. RECEIVING HOODS |
  • | - Thermal Canopy Hoods: Capture rising hot buoyant plumes |
  • | - Grinding Wheel Hoods: Capture projectile momentum of particles |
  • | |
  • | 3. EXTERIOR HOODS |
  • | - Plain Open Ducts: Freestanding round/rectangular suction mouths |
  • | - Flanged Exterior Hoods: Flange plates eliminate rear air draw |
  • | - Slot Hoods / Plenums: Uniform linear velocity along tank edges |
  • | - Downdraft Tables: Suction pulled downward through perforated grid |
  • +-------------------------------------------------------------------------+
  • Enclosing Hoods

Enclosing hoods surround the contaminant generation source completely or partially. They represent the most aerodynamically efficient hood design because they isolate the process from cross-drafts and require the lowest volumetric airflow (Q) per unit process area.

Complete Enclosures (Gloveboxes, Isolators):

Process is 100% sealed under negative static pressure (typically -0.5 to -1.0 in. w.g.). Air enters only through HEPA intake filters, and workers manipulate materials through sealed, impermeable elastomeric gloves.

Applications: Highly potent pharmaceutical compounds (OEB 4/5), radiochemistry, handling pyrophoric or infectious pathogens (BSL-3/4).

Partial Enclosures (Laboratory Chemical Fume Hoods):

Provide an open frontal access area (face) with an adjustable sliding sash (vertical, horizontal, or combination).

Face Velocity Standards (ANSI/ASSP Z9.5 & OSHA 1910.1450):

Standard operating face velocity: 80 to 120 fpm (0.4 to 0.6 m/s) across the active sash opening (typically verified at a standard operating sash height of 18 inches / 45 cm).

Face Velocity Upper Limit: Operating a chemical fume hood above 150 fpm (0.75 m/s) creates internal turbulent eddy currents behind the sash lip and around the worker's torso, causing wake vortices that pull contaminants out of the hood into the breathing zone.

Bypass Design: Modern constant air volume (CAV) bypass fume hoods incorporate an upper bypass grille that opens as the sash is lowered, maintaining a relatively constant face velocity rather than allowing dangerous velocity spikes at low sash heights.

Receiving Hoods

Receiving hoods are positioned to intercept a contaminant stream that possesses an intrinsic initial directional velocity or buoyant momentum generated by the process itself.

Canopy Hoods: Positioned directly above hot processes (e.g., molten metal furnaces, commercial deep fryers, hot dye vats). The hot process heats ambient air, creating a rising thermal convective plume. Canopy hoods must be sized larger than the process footprint to encompass the expanding conical plume (30° spread angle).

Grinding and Buffing Hoods: Positioned directly in line with the tangential projectile trajectory of sparks, grit, and metallic dust thrown off by high-speed rotating wheels, utilizing the kinetic energy of the particles to deliver them into the hood mouth.

Exterior Hoods

Exterior hoods are located adjacent to an emitting process without enclosing it. Because the contaminant is released outside the physical hood boundary with little or no directional momentum toward the hood, the hood must generate an active air current across the intervening space to capture and draw the contaminant into the duct.

Flanged Exterior Hoods: Adding a flat, perpendicular flange around the perimeter of an exterior hood opening redirects air inflow, eliminating unwanted airflow from behind the hood and increasing capture velocity in front of the hood by 25% to 33% for the same volumetric flow rate.

Slot Hoods on Open Surface Tanks: Narrow horizontal or lateral slots attached to an exhaust plenum provide uniform linear capture across broad liquid surfaces (e.g., electroplating baths, degreasing tanks, pickling tanks) while keeping ductwork unobstructed above the tank.

Downdraft Tables: Draw air downward through a perforated workbench grid, utilizing gravity to assist in capturing dense solvent vapors or heavy grinding/sanding dusts away from the operator's breathing zone.

3. Capture Velocity (Vc) Selection Criteria

Capture velocity (Vc) is the minimum air velocity required at the most distant point of contaminant generation to overcome cross-drafts, ambient room air currents, and contaminant momentum, successfully drawing the contaminant into the exhaust hood. +-------------------------------------------------------------------------+

  • | CAPTURE VELOCITY SELECTION HIERARCHY |
  • +-------------------------------------------------------------------------+
  • | Condition / Contaminant Release Profile | Capture Velocity|
  • +-------------------------------------------------------+-----------------+
  • | Quiet evaporation; gas/vapor release with practically| 50 - 100 fpm |
  • | no velocity into still room air (e.g., solvent tanks)| (0.25 - 0.5 m/s)|
  • +-------------------------------------------------------+-----------------+
  • | Low to moderate release velocity into moderate room | 100 - 200 fpm |
  • | cross-drafts (e.g., welding, barrel filling, plating)| (0.5 - 1.0 m/s) |
  • +-------------------------------------------------------+-----------------+
  • | Active generation; high-speed release into rapid room| 200 - 500 fpm |
  • | air motion (e.g., conveyor loading, crushers, paint) | (1.0 - 2.5 m/s) |
  • +-------------------------------------------------------+-----------------+
  • | High initial mechanical velocity; extreme momentum | 500 - 2,000 fpm |
  • | (e.g., grinding, abrasive blasting, fast spinning) | (2.5 - 10.0 m/s)|
  • +-------------------------------------------------------------------------+
  • Key Determinants of Capture Velocity Selection

When selecting the design capture velocity within a given range (e.g., selecting 100 fpm vs. 200 fpm for welding), the industrial hygienist must apply the higher end of the range if:

Room cross-drafts are significant (e.g., cross-drafts > 50 fpm from pedestrian traffic, supply diffusers, or open bay doors).

Contaminant toxicity is high (low OEL / TLV, carcinogen, sensitizer).

Process generation rate is intermittent or surging .

Worker position is between the hood and the source (to avoid pulling contaminants across the breathing zone).