Study guide

14.2 Calorimetry, Specific Heat & Enthalpy (ΔH)

CLEP Chemistry Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Strategy

1.1 CLEP Chemistry Exam Structure, Calculator & Periodic Table 1.2 Quantitative Foundations: Units, Dimensional Analysis & Significant Figures 1.3 Effective Study Strategies & Recommended Course Pathway

2 Chapter 2: Atomic Theory, Isotopes & Nuclear Chemistry

2.1 Evolution of Atomic Theory, Subatomic Particles & Mass Spectrometry 2.2 Quantum Numbers, Atomic Spectra & Electron Configurations 2.3 Nuclear Chemistry: Radiation, Decay Kinetics & Nuclear Reactions

3 Chapter 3: Periodic Relationships & Periodicity

3.1 Periodic Law & Periodic Table Organization 3.2 Periodic Trends: Atomic/Ionic Radii, Ionization Energy, Electron Affinity & Electronegativity 3.3 Oxidation States & Valence Electron Trends

4 Chapter 4: Chemical Bonding & Molecular Structure

4.1 Ionic, Covalent, Polar Covalent & Metallic Bonding 4.2 Lewis Structures, Formal Charges & Resonance 4.3 VSEPR Theory, Molecular Geometries & Polarity 4.4 Valence Bond Theory, Hybridization & Sigma/Pi Bonding

5 Chapter 5: Gases & Kinetic Molecular Theory

5.1 Gas Laws & the Ideal Gas Equation (PV = nRT) 5.2 Gas Mixtures: Dalton's Law of Partial Pressures & Graham's Law 5.3 Kinetic Molecular Theory & Maxwell-Boltzmann Distribution 5.4 Real Gases & Deviations from Ideal Behavior (van der Waals Equation)

6 Chapter 6: Condensed Phases & Phase Changes

6.1 Intermolecular Forces in Liquids & Solids 6.2 Phase Changes, Heating Curves & Vapor Pressure 6.3 Phase Diagrams & Critical Phenomena

7 Chapter 7: Solutions & Colligative Properties

7.1 Solution Formation, Solubility Factors & Henry's Law 7.2 Concentration Units: Molarity, Molality, Mole Fraction & Mass Percent 7.3 Colligative Properties & Raoult's Law 7.4 Electrolytes, Interionic Attractions & the van 't Hoff Factor

8 Chapter 8: Chemical Equations & Stoichiometry

8.1 Chemical Equations, Types of Reactions & Net Ionic Equations 8.2 The Mole Concept, Molar Mass & Empirical/Molecular Formulas 8.3 Reaction Stoichiometry, Limiting Reactants & Percent Yield

9 Chapter 9: Aqueous Reaction Types

9.1 Precipitation Reactions & Solubility Rules 9.2 Acid-Base Reactions & Neutralization 9.3 Coordination Compounds & Complex Ion Formation

10 Chapter 10: Oxidation-Reduction Reactions & Electrochemistry

10.1 Oxidation States & Balancing Redox Reactions by Half-Reaction Method 10.2 Voltaic (Galvanic) Cells & Standard Reduction Potentials 10.3 Cell Potential, Gibbs Free Energy & Equilibrium (Nernst Equation) 10.4 Electrolytic Cells & Faraday's Laws of Electrolysis

11 Chapter 11: Chemical Equilibrium & Dynamic Systems

11.1 Nature of Dynamic Equilibrium & Equilibrium Expressions (Kc, Kp) 11.2 Le Chatelier's Principle & Perturbations to Systems at Equilibrium 11.3 Equilibrium Calculations & the Reaction Quotient (Q vs K)

12 Chapter 12: Aqueous Equilibria: Acids, Bases & Solubility

12.1 Autoionization of Water, pH Scale & Strong vs Weak Acids/Bases 12.2 Acid-Base Equilibria (Ka, Kb), Polyprotic Acids & Salt Hydrolysis 12.3 Buffer Systems, Henderson-Hasselbalch Equation & Solubility Product (Ksp)

13 Chapter 13: Reaction Kinetics & Rate Laws

13.1 Reaction Rates, Rate Laws & Determination of Reaction Order 13.2 Integrated Rate Laws, Graphical Methods & Half-Lives 13.3 Collision Theory, Activation Energy & the Arrhenius Equation 13.4 Reaction Mechanisms, Elementary Steps & Catalysis

14 Chapter 14: Thermochemistry & Thermodynamics

14.1 Energy, Heat, Work & the First Law of Thermodynamics 14.2 Calorimetry, Specific Heat & Enthalpy (ΔH) 14.3 Hess's Law & Standard Enthalpies of Formation 14.4 Entropy (ΔS), Gibbs Free Energy (ΔG) & Spontaneity

15 Chapter 15: Descriptive Chemistry of the Elements

15.1 Horizontal, Vertical & Diagonal Periodic Relationships 15.2 Representative Main-Group Chemistry: Alkali, Alkaline Earth & Halogens 15.3 Transition Metals: Configurations, Colors & Common Reactivity 15.4 Main Groups 13–16 & Hydrogen: Characteristic Compounds and Reaction Products 15.5 Systematic Inorganic Nomenclature: Ionic Compounds, Polyatomic Ions, Acids & Molecular Compounds

16 Chapter 16: Fundamentals of Organic Chemistry

16.1 Hydrocarbons: Alkanes, Alkenes, Alkynes & Aromatic Systems 16.2 Major Functional Groups & IUPAC Nomenclature 16.3 Structural & Geometric Isomerism in Organic Compounds

17 Chapter 17: Laboratory Techniques & Analytical Methods

17.1 Essential Laboratory Apparatus & Measurement Uncertainty 17.2 Quantitative Analytical Methods: Titration & Gravimetric Analysis 17.3 Spectrophotometry, Beer's Law & Chromatography

18 Chapter 18: Laboratory Safety, Error Analysis & Scientific Deduction

18.1 Chemical Hazards, SDS/GHS Standards & Safety Protocols 18.2 Error Analysis: Systematic vs Random Errors & Percent Error 18.3 Data Interpretation, Graphical Analysis & Scientific Deduction

14.2 Calorimetry, Specific Heat & Enthalpy (ΔH)

Key Takeaways Explain This Topic AI

Specific heat capacity (c) is an intensive thermal property quantifying heat required to raise 1 gram of a substance by 1 °C, governed by the calorimetric heat equation q = m * c * ΔT.

Constant-pressure calorimetry (coffee-cup calorimeter) measures aqueous reaction enthalpies (ΔH_rxn = q_p / n_limiting), where heat released or absorbed by the reaction is captured by the solution and calorimeter: q_rxn = -q_calorimeter.

Constant-volume calorimetry (bomb calorimeter) enforces ΔV = 0 (w = 0) to determine internal energies of combustion (ΔU_comb = q_v = -C_bomb * ΔT), which relate to enthalpy via ΔH = ΔU + Δn_gas * R * T.

Latent heat transitions (fusion, vaporization, sublimation) occur isothermally at phase boundaries, where heat supplied breaks intermolecular attractions without increasing temperature.

Thermochemical equations treat reaction enthalpy as a stoichiometric quantity, enabling direct stoichiometric proportions between chemical moles reacted and thermal energy exchanged.

Last updated: September 2026

14.2 Calorimetry, Specific Heat & Enthalpy (ΔH)

Quick Summary: Calorimetry experimentally measures heat transferred during physical and chemical processes. Thermal transfer is quantified by heat capacity ( C C C ), specific heat capacity ( c c c ), and molar heat capacity ( C m C_m C m ​ ) using q = m ⋅ c ⋅ Δ T q = m \cdot c \cdot \Delta T q = m ⋅ c ⋅ Δ T . Constant-pressure calorimetry ("coffee-cup") measures aqueous solution reactions where q rxn = − q calorimeter = Δ H rxn q_{\text{rxn}} = -q_{\text{calorimeter}} = \Delta H_{\text{rxn}} q rxn ​ = − q calorimeter ​ = Δ H rxn ​ . Constant-volume calorimetry ("bomb") suppresses expansion ( Δ V = 0 , w = 0 \Delta V = 0, w = 0 Δ V = 0 , w = 0 ), measuring combustion heats as internal energy changes ( q v = Δ U q_v = \Delta U q v ​ = Δ U ). Phase changes occur isothermally, governed by latent heats of fusion ( Δ H fus \Delta H_{\text{fus}} Δ H fus ​ ), vaporization ( Δ H vap \Delta H_{\text{vap}} Δ H vap ​ ), and sublimation ( Δ H sub \Delta H_{\text{sub}} Δ H sub ​ ).

1. Heat Capacity, Specific Heat & Molar Heat Capacity

When heat enters or leaves a substance without changing its phase or chemical composition, temperature changes proportionally to the quantity of thermal energy transferred:

Definitions & Distinctions

Heat Capacity ( C C C ): Heat required to raise sample temperature by 1 ∘ C 1\ ^\circ\text{C} 1 ∘ C (or 1 K 1\text{ K} 1 K ): C = q Δ T [ Units: J/ ∘ C or J/K ] C = \frac{q}{\Delta T} \quad [\text{Units: J/}^\circ\text{C or J/K}] C = Δ T q ​ [ Units: J/ ∘ C or J/K ] Heat capacity is an extensive property that scales directly with sample mass.

Specific Heat Capacity ( c c c ): Heat required to raise 1 gram 1\text{ gram} 1 gram of substance by 1 ∘ C 1\ ^\circ\text{C} 1 ∘ C : c = q m ⋅ Δ T [ Units: J/(g ⋅ ∘ C) ] c = \frac{q}{m \cdot \Delta T} \quad [\text{Units: J/(g}\cdot^\circ\text{C)}] c = m ⋅ Δ T q ​ [ Units: J/(g ⋅ ∘ C) ] Specific heat is an intensive property characteristic of the pure material.

Molar Heat Capacity ( C m C_m C m ​ ): Heat required to raise 1 mole 1\text{ mole} 1 mole of substance by 1 ∘ C 1\ ^\circ\text{C} 1 ∘ C : C m = q n ⋅ Δ T [ Units: J/(mol ⋅ ∘ C) ] C_m = \frac{q}{n \cdot \Delta T} \quad [\text{Units: J/(mol}\cdot^\circ\text{C)}] C m ​ = n ⋅ Δ T q ​ [ Units: J/(mol ⋅ ∘ C) ]

The Fundamental Calorimetric Equation q = m ⋅ c ⋅ Δ T = m ⋅ c ⋅ ( T final − T initial ) q = m \cdot c \cdot \Delta T = m \cdot c \cdot (T_{\text{final}} - T_{\text{initial}}) q = m ⋅ c ⋅ Δ T = m ⋅ c ⋅ ( T final ​ − T initial ​ )

where Δ T > 0 \Delta T > 0 Δ T > 0 denotes heat absorbed and Δ T < 0 \Delta T < 0 Δ T < 0 denotes heat released.

Reference Table: Specific Heat Capacities

Substance State Specific Heat c c c [ J/(g ⋅ ∘ C) \text{J/(g}\cdot^\circ\text{C)} J/(g ⋅ ∘ C) ] Physical Origin

  • Liquid Water Liquid 4.184 4.184 4.184 Hydrogen-bonding network absorbs substantial energy
  • Ice Solid 2.09 2.09 2.09 Rigid crystal lattice limits molecular motions
  • Steam Gas 2.01 2.01 2.01 Gaseous rotational and vibrational states

Aluminum Solid 0.900 0.900 0.900 Moderate heat capacity; low atomic mass ( 26.98 g/mol 26.98\text{ g/mol} 26.98 g/mol )

Copper Solid 0.385 0.385 0.385 Dense metal lattice; rapid thermal conduction

Liquid water's remarkably high specific heat capacity allows large bodies of water to moderate climate extremes.

2. Constant-Pressure ("Coffee-Cup") Calorimetry

Constant-pressure calorimetry measures enthalpy changes in aqueous reactions ( P ext = constant P_{\text{ext}} = \text{constant} P ext ​ = constant ), meaning q rxn = q p = Δ H rxn q_{\text{rxn}} = q_p = \Delta H_{\text{rxn}} q rxn ​ = q p ​ = Δ H rxn ​ .

Conservation of Energy in Solution

In an insulated polystyrene cup open to atmospheric pressure: q system + q surroundings = 0 ⟹ q rxn = − q calorimeter q_{\text{system}} + q_{\text{surroundings}} = 0 \implies q_{\text{rxn}} = -q_{\text{calorimeter}} q system ​ + q surroundings ​ = 0 ⟹ q rxn ​ = − q calorimeter ​ q calorimeter = m soln ⋅ c soln ⋅ Δ T + C cal ⋅ Δ T q_{\text{calorimeter}} = m_{\text{soln}} \cdot c_{\text{soln}} \cdot \Delta T + C_{\text{cal}} \cdot \Delta T q calorimeter ​ = m soln ​ ⋅ c soln ​ ⋅ Δ T + C cal ​ ⋅ Δ T

Neglecting C cal C_{\text{cal}} C cal ​ and approximating dilute solutions as water ( c = 4.184 J/(g ⋅ ∘ C) c = 4.184\text{ J/(g}\cdot^\circ\text{C)} c = 4.184 J/(g ⋅ ∘ C) , ρ = 1.00 g/mL \rho = 1.00\text{ g/mL} ρ = 1.00 g/mL ): q rxn = − ( m soln ⋅ 4.184 ⋅ Δ T ) q_{\text{rxn}} = -(m_{\text{soln}} \cdot 4.184 \cdot \Delta T) q rxn ​ = − ( m soln ​ ⋅ 4.184 ⋅ Δ T )

Per mole of limiting reactant: Δ H rxn = q rxn n limiting \Delta H_{\text{rxn}} = \frac{q_{\text{rxn}}}{n_{\text{limiting}}} Δ H rxn ​ = n limiting ​ q rxn ​ ​

3. Constant-Volume ("Bomb") Calorimetry

Combustion reactions producing high pressures are conducted in a constant-volume bomb calorimeter :

The sample is ignited in excess oxygen inside a rigid steel vessel ("bomb") submerged in water.

Because volume is fixed ( Δ V = 0 \Delta V = 0 Δ V = 0 ), no expansion work occurs ( w = 0 w = 0 w = 0 ): Δ U comb = q v = − C bomb ⋅ Δ T \Delta U_{\text{comb}} = q_v = -C_{\text{bomb}} \cdot \Delta T Δ U comb ​ = q v ​ = − C bomb ​ ⋅ Δ T

where C bomb C_{\text{bomb}} C bomb ​ is the calibrated total heat capacity of the bomb, water, and vessel.

Reaction enthalpy connects via Δ H = Δ U + Δ n gas R T \Delta H = \Delta U + \Delta n_{\text{gas}} RT Δ H = Δ U + Δ n gas ​ RT .

4. Latent Heats of Phase Transitions

Phase changes occur isothermally at transition temperatures as heat alters intermolecular attractions:

Enthalpy of Fusion ( Δ H fus \Delta H_{\text{fus}} Δ H fus ​ ): Heat needed to melt 1 mole 1\text{ mole} 1 mole of solid (for water, + 6.01 kJ/mol +6.01\text{ kJ/mol} + 6.01 kJ/mol ).

Enthalpy of Vaporization ( Δ H vap \Delta H_{\text{vap}} Δ H vap ​ ): Heat needed to vaporize 1 mole 1\text{ mole} 1 mole of liquid (for water, + 40.67 kJ/mol +40.67\text{ kJ/mol} + 40.67 kJ/mol ).

Enthalpy of Sublimation ( Δ H sub \Delta H_{\text{sub}} Δ H sub ​ ): Direct solid-to-gas conversion: Δ H sub = Δ H fus + Δ H vap \Delta H_{\text{sub}} = \Delta H_{\text{fus}} + \Delta H_{\text{vap}} Δ H sub ​ = Δ H fus ​ + Δ H vap ​

Vaporization requires far greater energy than fusion because molecules must separate entirely against intermolecular attractions.

5. Thermochemical Equations & Stoichiometry

A thermochemical equation specifies stoichiometry alongside molar enthalpy ( Δ H ∘ \Delta H^\circ Δ H ∘ ): 2 H 2 ( g ) + O 2 ( g ) ⟶ 2 H 2 O ( l ) Δ H ∘ = − 571.6 kJ 2\text{ H}_2(g) + \text{O}_2(g) \longrightarrow 2\text{ H}_2\text{O}(l) \quad \Delta H^\circ = -571.6\text{ kJ} 2 H 2 ​ ( g ) + O 2 ​ ( g ) ⟶ 2 H 2 ​ O ( l ) Δ H ∘ = − 571.6 kJ

Enthalpy is proportional to moles reacted: − 571.6 kJ 2 mol H 2 = − 571.6 kJ 1 mol O 2 = − 571.6 kJ 2 mol H 2 O ( l ) \frac{-571.6\text{ kJ}}{2\text{ mol H}_2} = \frac{-571.6\text{ kJ}}{1\text{ mol O}_2} = \frac{-571.6\text{ kJ}}{2\text{ mol H}_2\text{O}(l)} 2 mol H 2 ​ − 571.6 kJ ​ = 1 mol O 2 ​ − 571.6 kJ ​ = 2 mol H 2 ​ O ( l ) − 571.6 kJ ​

Reversing an equation changes the sign of Δ H ∘ \Delta H^\circ Δ H ∘ ; halving coefficients divides Δ H ∘ \Delta H^\circ Δ H ∘ by 2.

  • 6. Worked Quantitative Calorimetry Examples
  • Example 1: Coffee-Cup Neutralization Calorimetry

Problem: Mixing 50.0 mL 50.0\text{ mL} 50.0 mL of 1.00 M HCl 1.00\text{ M HCl} 1.00 M HCl with 50.0 mL 50.0\text{ mL} 50.0 mL of 1.00 M NaOH 1.00\text{ M NaOH} 1.00 M NaOH at 22.0 ∘ C 22.0\ ^\circ\text{C} 22.0 ∘ C in a calorimeter causes temperature to rise to 28.7 ∘ C 28.7\ ^\circ\text{C} 28.7 ∘ C . With total mass 100.0 g 100.0\text{ g} 100.0 g and c = 4.184 J/(g ⋅ ∘ C) c = 4.184\text{ J/(g}\cdot^\circ\text{C)} c = 4.184 J/(g ⋅ ∘ C) , determine Δ H rxn \Delta H_{\text{rxn}} Δ H rxn ​ per mole.

Step 1: Calculate heat absorbed by solution Δ T = 28.7 ∘ C − 22.0 ∘ C = + 6.7 ∘ C \Delta T = 28.7\ ^\circ\text{C} - 22.0\ ^\circ\text{C} = +6.7\ ^\circ\text{C} Δ T = 28.7 ∘ C − 22.0 ∘ C = + 6.7 ∘ C q soln = ( 100.0 g ) ( 4.184 J/(g ⋅ ∘ C) ) ( 6.7 ∘ C ) = + 2803 J = + 2.803 kJ q_{\text{soln}} = (100.0\text{ g})(4.184\text{ J/(g}\cdot^\circ\text{C)})(6.7\ ^\circ\text{C}) = +2803\text{ J} = +2.803\text{ kJ} q soln ​ = ( 100.0 g ) ( 4.184 J/(g ⋅ ∘ C) ) ( 6.7 ∘ C ) = + 2803 J = + 2.803 kJ

Step 2: Determine molar enthalpy q rxn = − 2.803 kJ , n = ( 0.0500 L ) ( 1.00 M ) = 0.0500 mol q_{\text{rxn}} = -2.803\text{ kJ}, \quad n = (0.0500\text{ L})(1.00\text{ M}) = 0.0500\text{ mol} q rxn ​ = − 2.803 kJ , n = ( 0.0500 L ) ( 1.00 M ) = 0.0500 mol Δ H rxn = − 2.803 kJ 0.0500 mol = − 56.1 kJ/mol \Delta H_{\text{rxn}} = \frac{-2.803\text{ kJ}}{0.0500\text{ mol}} = -56.1\text{ kJ/mol} Δ H rxn ​ = 0.0500 mol − 2.803 kJ ​ = − 56.1 kJ/mol

Example 2: Bomb Calorimetry Combustion

Problem: Combusting 1.015 g 1.015\text{ g} 1.015 g sucrose ( 342.3 g/mol 342.3\text{ g/mol} 342.3 g/mol ) in a bomb calorimeter with C bomb = 4.90 kJ/ ∘ C C_{\text{bomb}} = 4.90\text{ kJ/}^\circ\text{C} C bomb ​ = 4.90 kJ/ ∘ C raises temperature by 3.41 ∘ C 3.41\ ^\circ\text{C} 3.41 ∘ C . Find Δ U comb \Delta U_{\text{comb}} Δ U comb ​ per mole. q calorimeter = ( 4.90 kJ/ ∘ C ) ( 3.41 ∘ C ) = + 16.71 kJ ⟹ q rxn = − 16.71 kJ q_{\text{calorimeter}} = (4.90\text{ kJ/}^\circ\text{C})(3.41\ ^\circ\text{C}) = +16.71\text{ kJ} \implies q_{\text{rxn}} = -16.71\text{ kJ} q calorimeter ​ = ( 4.90 kJ/ ∘ C ) ( 3.41 ∘ C ) = + 16.71 kJ ⟹ q rxn ​ = − 16.71 kJ n = 1.015 g 342.3 g/mol = 0.002965 mol n = \frac{1.015\text{ g}}{342.3\text{ g/mol}} = 0.002965\text{ mol} n = 342.3 g/mol 1.015 g ​ = 0.002965 mol Δ U comb = − 16.71 kJ 0.002965 mol = − 5.64 × 10 3 kJ/mol \Delta U_{\text{comb}} = \frac{-16.71\text{ kJ}}{0.002965\text{ mol}} = -5.64 \times 10^3\text{ kJ/mol} Δ U comb ​ = 0.002965 mol − 16.71 kJ ​ = − 5.64 × 1 0 3 kJ/mol