Study guide

Chemical, Heat/UV, Hydrogen Peroxide & Neutralization

NCLE CLRE Contact Lens Registry Exam Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

0.1 About the CLRE Exam 0.2 How to Use This Study Guide

2 Ocular Anatomy: Adnexa

Tear Film: Layers, Glands & Break-Up Time Conjunctiva, Lids, Lashes, Fornix & Canthi Blink Rate, Lid Function & Contact Lens Wear Effects

3 Ocular Anatomy: Anterior & Posterior Segment

Corneal Layers, Curvature, Topography & Metabolism Iris, Pupil, Sclera & Anterior Chamber Crystalline Lens, Retina, Choroid & Posterior Chamber

4 Refractive Errors & Contact Lens Optics

Myopia, Hyperopia, Astigmatism, Presbyopia & Anisometropia Refraction, Prism, Lacrimal Lens, Accommodation & Transposition Vertex Distance, Sagittal Depth & Spherical Equivalent

5 Measurement Instrumentation

Keratometer/Ophthalmometer: Calibration, Readings & Interpretation Corneal Topography & OCT for Contact Lens Fitting Schirmer Tests & Tear Break-Up Time

6 Observation & Verification Instrumentation

Slit Lamp (Biomicroscope) Operation & Illumination Slit Lamp Evaluation With & Without Contact Lenses Radiuscope, Lensometer, Thickness Gauge & ANSI Z80

7 Prefitting Patient Evaluation

6.1 Lifestyle, Occupation, Environment & Motivation 6.2 Medical History, Diseases, Medications & Allergies 6.3 Contraindications & Factors for Successful Wear 6.4 Relating Corneal Measurements, Rx & Lens Parameters

8 Lens Materials, Design & Parameter Selection

Dk, Dk/t, Thermal Conductivity & Holden-Mertz Water Content, Wetting Angle, Modulus, Silicone Hydrogel & Surface Treatments Toric, Multifocal, Aspheric, Hybrid, Scleral, Orthokeratology & Quadrant-Specific Base Curve, Peripheral Curves, Diameter, Thickness, Power & Edge Design

9 Diagnostic Fitting Procedures

8.1 Lens Selection & Application Procedures 8.2 Fluorescein Pattern Evaluation for RGP Lenses 8.3 Soft Lens Movement, Centration & Coverage

10 Fit Evaluation & Over-Refraction

Toric Lens Axis Rotation, LARS Rule & Stabilization Patient Comfort, Visual Acuity & Over-Refraction Modifying Base Curve, Diameter, Sag & Power from Findings

11 Dispensing: Wearing Schedules & Replacement

Daily, Flexible & Extended/Continuous Wear Schedules Daily, Biweekly, Monthly & Conventional Replacement Adaptation Protocols & Patient Compliance Counseling

12 Dispensing: Lens Care Systems

Solution Compatibility with Lens Types Chemical, Heat/UV, Hydrogen Peroxide & Neutralization Surfactant Cleaners, Protein Removers & Weekly Cleaning Solution Sensitivities, Incompatibilities & Adverse Reactions

13 Dispensing: Handling & Hygiene

12.1 Soft Lens Insertion & Removal Techniques 12.2 RGP Insertion, Removal & Emergency Responses 12.3 Hygiene, Soaps, Cosmetics & Storage Containers 12.4 Verifying Lens Parameters Against the Order at Dispensing

14 Follow-Up: Subjective & Objective Findings

13.1 Subjective Complaints: Dryness, Awareness, Blurry Vision, Pain & Photophobia 13.2 Steep vs Flat Lens Fit (Rigid & Soft) & Everted Lens 13.3 Injection, Edema, Discharge, Vision Loss & Lid Problems 13.4 Visual Acuity, Over-Refraction & Gross Evaluation Techniques

15 Follow-Up: Staining Patterns & Complications

14.1 Staining Patterns: 3 & 9 O'Clock, Foreign Body, SPK, Arcuate, Smile & Dimple Veiling 14.2 SEAL, CLARE, VLK, SLK & CLPU 14.3 Microbial Keratitis, Acanthamoeba, Dendritic Ulcer & Infiltrates 14.4 Corneal Molding/Warpage, Dellen & Mucin Balls

16 Follow-Up: Management Protocols

GPC, Blepharitis, Ptosis & Tarsal Plate Evaluation Daily Wear, Extended, Therapeutic, Postsurgical & Pathology Protocols Changing Lens Parameters at Follow-Up & Documenting Records

17 Regulatory & Administrative

FCLCA, FDA, FTC, Contact Lens Rule & Prescriber Verification HIPAA, PHI, OSHA, CDC, ANSI & Universal Precautions Record Retention, Inventory, Ordering & Documentation Methodology

Chemical, Heat/UV, Hydrogen Peroxide & Neutralization

Key Takeaways Explain This Topic AI

Chemical (MPS) disinfection uses biguanides (PHMB), polyquad, or alexidine and requires a 4–6 hour soak to achieve full disinfection

Heat disinfection at 80°C for 10 minutes is effective but can warp some soft lens materials and is contraindicated for many silicone hydrogels

Hydrogen peroxide (3%) is the only preservative-free disinfection method and requires neutralization via a catalytic disc, platinum ring, or separate neutralizer

One-step peroxide systems neutralize over 6 hours; two-step systems require the patient to add a neutralizing tablet or solution

An unneutralized peroxide-soaked lens inserted into the eye produces a severe chemical burn — patients must be explicitly counseled to wait for the full cycle

Last updated: July 2026

Chemical, Heat/UV, Hydrogen Peroxide & Neutralization

Quick Answer: Four disinfection methods are used in CL care: chemical (MPS) with biguanides, polyquad, or alexidine (4–6 hour soak), heat at 80°C for 10 minutes, UV with a photosensitizer , and hydrogen peroxide 3% with mandatory neutralization. Heat is effective but warps some materials. Hydrogen peroxide is preservative-free and the safest choice for sensitive patients, but inserting an unneutralized peroxide lens causes a severe chemical burn.

Comparison of Disinfection Methods

  • Method Active Agent Time Material Compatibility Preservative-Free Key Risk
  • Chemical (MPS) PHMB, Polyquad, Alexidine 4–6 hours Most soft, many RGP No Preservative sensitivity, SICS

Heat 80°C water bath, 10 min 10 min + cool-down Only specific soft materials (low water, non-ionic) Yes Lens warpage, parameter change

UV + photosensitizer UV light with photoactive agent 10–30 min Material-dependent Varies Limited availability, less common in U.S.

Hydrogen peroxide 3% H₂O₂, neutralized to saline 6 hours (one-step) All soft and RGP Yes (after neutralization) Chemical burn if not neutralized

Chemical Disinfection (MPS)

Chemical disinfection relies on cationic preservatives that disrupt microbial cell membranes. The three major active agents are:

Polyhexanide (PHMB / polyhexamethylene biguanide) — broad-spectrum against bacteria, fair against fungi and Acanthamoeba cysts; concentration 1 ppm

Polyquad (polyquaternium-1) — quaternary ammonium, very low sensitivity profile, commonly used in Opti-Free formulations

Alexidine — biguanide with rapid kill kinetics, used in some newer MPS products

Chemical disinfection requires a minimum soak time of 4–6 hours . Removing lenses earlier compromises disinfection efficacy. The lens case must be rubbed and rinsed, then air-dried daily; the case itself should be replaced at least every 3 months.

Heat Disinfection

Heat disinfection uses a controlled water bath at 80°C (176°F) for 10 minutes , followed by a cool-down period before insertion. It is preservative-free and was historically popular for patients sensitive to chemical preservatives.

Material limitations are critical:

Approved for low-water, non-ionic soft lenses (e.g., original Sauflon, some HEMA lenses)

Contraindicated for high-water, ionic, and most silicone hydrogel lenses — heat warps parameters, reverses surface treatments, and can cause lens shrinkage

Generally not used for RGP lenses

Heat units must be monitored for proper temperature calibration; a malfunctioning unit can either fail to disinfect or melt the lens.

Ultraviolet (UV) Disinfection

UV disinfection uses ultraviolet light combined with a photosensitizer (a photoactive additive in the solution). The UV activates the photosensitizer, generating reactive oxygen species that kill microbes. The system is material-dependent and requires a specialized unit and compatible solution. It is less common in U.S. practice than chemical or peroxide systems but appears on the NCLE as a recognized method. UV disinfection does not work with plain saline alone—the photosensitizer solution is required.

Hydrogen Peroxide 3%

Hydrogen peroxide is the most effective disinfectant in CL care, with broad activity against bacteria, fungi, protozoa, and viruses at 3% concentration. Its major advantage is that, after neutralization, the lens sits in preservative-free saline , making it the system of choice for:

  • Patients with preservative allergies or sensitivities
  • Patients with solution-induced corneal staining (SICS)
  • Patients with recurrent GPC triggered by preservatives
  • Pediatric and therapeutic lens wearers
  • Two-Step Systems

Two-step systems require the patient to add a neutralizing tablet (typically catalase or sodium pyruvate) or rinse with a separate neutralizing solution after the disinfection cycle. The lens case has two compartments or two timed steps. Two-step systems offer tighter control over neutralization timing but rely more on patient compliance.

One-Step Systems

One-step systems use a catalytic disc or platinum ring built into the lens case. The disc slowly neutralizes the peroxide to saline and water over 6 hours . The patient simply fills the case with peroxide, drops the lenses in, and lets it sit overnight.

  • Critical Safety Counseling
  • NEVER insert a lens directly from a peroxide case before the full 6-hour cycle completes

Burning, redness, tearing, and chemical injury occur within seconds of inserting an unneutralized peroxide lens

The case must be rinsed and air-dried daily; the catalytic disc must be replaced per manufacturer schedule (typically every 30 days or per case replacement)

Patients must use only the peroxide solution specified for the system—never substitute household hydrogen peroxide

Selecting a Method for the Patient

  • Patient Profile Preferred Method
  • Healthy soft CL wearer, no sensitivities MPS (chemical)
  • Documented preservative sensitivity or SICS Hydrogen peroxide
  • Recurrent GPC or papillary reaction Hydrogen peroxide or daily disposable
  • Conventional low-water soft lens, preservative-sensitive Heat (if material approved)
  • RGP wearer RGP-specific MPS or peroxide (if approved)
  • Therapeutic, pediatric, or post-surgical Hydrogen peroxide (preservative-free)

The dispensing optician must verify material compatibility in the manufacturer's labeling and document the care system recommended at dispensing.