Study guide

Base Curve, Peripheral Curves, Diameter, Thickness, Power & Edge Design

NCLE CLRE Contact Lens Registry Exam Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

0.1 About the CLRE Exam 0.2 How to Use This Study Guide

2 Ocular Anatomy: Adnexa

Tear Film: Layers, Glands & Break-Up Time Conjunctiva, Lids, Lashes, Fornix & Canthi Blink Rate, Lid Function & Contact Lens Wear Effects

3 Ocular Anatomy: Anterior & Posterior Segment

Corneal Layers, Curvature, Topography & Metabolism Iris, Pupil, Sclera & Anterior Chamber Crystalline Lens, Retina, Choroid & Posterior Chamber

4 Refractive Errors & Contact Lens Optics

Myopia, Hyperopia, Astigmatism, Presbyopia & Anisometropia Refraction, Prism, Lacrimal Lens, Accommodation & Transposition Vertex Distance, Sagittal Depth & Spherical Equivalent

5 Measurement Instrumentation

Keratometer/Ophthalmometer: Calibration, Readings & Interpretation Corneal Topography & OCT for Contact Lens Fitting Schirmer Tests & Tear Break-Up Time

6 Observation & Verification Instrumentation

Slit Lamp (Biomicroscope) Operation & Illumination Slit Lamp Evaluation With & Without Contact Lenses Radiuscope, Lensometer, Thickness Gauge & ANSI Z80

7 Prefitting Patient Evaluation

6.1 Lifestyle, Occupation, Environment & Motivation 6.2 Medical History, Diseases, Medications & Allergies 6.3 Contraindications & Factors for Successful Wear 6.4 Relating Corneal Measurements, Rx & Lens Parameters

8 Lens Materials, Design & Parameter Selection

Dk, Dk/t, Thermal Conductivity & Holden-Mertz Water Content, Wetting Angle, Modulus, Silicone Hydrogel & Surface Treatments Toric, Multifocal, Aspheric, Hybrid, Scleral, Orthokeratology & Quadrant-Specific Base Curve, Peripheral Curves, Diameter, Thickness, Power & Edge Design

9 Diagnostic Fitting Procedures

8.1 Lens Selection & Application Procedures 8.2 Fluorescein Pattern Evaluation for RGP Lenses 8.3 Soft Lens Movement, Centration & Coverage

10 Fit Evaluation & Over-Refraction

Toric Lens Axis Rotation, LARS Rule & Stabilization Patient Comfort, Visual Acuity & Over-Refraction Modifying Base Curve, Diameter, Sag & Power from Findings

11 Dispensing: Wearing Schedules & Replacement

Daily, Flexible & Extended/Continuous Wear Schedules Daily, Biweekly, Monthly & Conventional Replacement Adaptation Protocols & Patient Compliance Counseling

12 Dispensing: Lens Care Systems

Solution Compatibility with Lens Types Chemical, Heat/UV, Hydrogen Peroxide & Neutralization Surfactant Cleaners, Protein Removers & Weekly Cleaning Solution Sensitivities, Incompatibilities & Adverse Reactions

13 Dispensing: Handling & Hygiene

12.1 Soft Lens Insertion & Removal Techniques 12.2 RGP Insertion, Removal & Emergency Responses 12.3 Hygiene, Soaps, Cosmetics & Storage Containers 12.4 Verifying Lens Parameters Against the Order at Dispensing

14 Follow-Up: Subjective & Objective Findings

13.1 Subjective Complaints: Dryness, Awareness, Blurry Vision, Pain & Photophobia 13.2 Steep vs Flat Lens Fit (Rigid & Soft) & Everted Lens 13.3 Injection, Edema, Discharge, Vision Loss & Lid Problems 13.4 Visual Acuity, Over-Refraction & Gross Evaluation Techniques

15 Follow-Up: Staining Patterns & Complications

14.1 Staining Patterns: 3 & 9 O'Clock, Foreign Body, SPK, Arcuate, Smile & Dimple Veiling 14.2 SEAL, CLARE, VLK, SLK & CLPU 14.3 Microbial Keratitis, Acanthamoeba, Dendritic Ulcer & Infiltrates 14.4 Corneal Molding/Warpage, Dellen & Mucin Balls

16 Follow-Up: Management Protocols

GPC, Blepharitis, Ptosis & Tarsal Plate Evaluation Daily Wear, Extended, Therapeutic, Postsurgical & Pathology Protocols Changing Lens Parameters at Follow-Up & Documenting Records

17 Regulatory & Administrative

FCLCA, FDA, FTC, Contact Lens Rule & Prescriber Verification HIPAA, PHI, OSHA, CDC, ANSI & Universal Precautions Record Retention, Inventory, Ordering & Documentation Methodology

Base Curve, Peripheral Curves, Diameter, Thickness, Power & Edge Design

Key Takeaways Explain This Topic AI

Central posterior curve (CPC / base curve) is the primary fitting curve, expressed in mm radius or diopters via r = 337.5 / D.

RGP peripheral curves (IPC, PPC) create edge lift and the tear pump; ideal RGP edge lift is 0.6–0.8 mm.

Soft lens diameters run 13.8–14.5 mm; RGP 8.5–9.5 mm; scleral 14.5–18+ mm — larger diameter raises sagittal depth.

Contact lens power must be vertex-compensated (F_cl = F_spec / (1 − d·F_spec)) for any Rx ≥ ±4.00 D; plus becomes more plus, minus becomes less minus.

Sagittal depth ties the system together: SAG rises with steeper BC and larger diameter — over-SAG tightens, under-SAG gives poor centration.

Last updated: July 2026

Base Curve, Peripheral Curves, Diameter, Thickness, Power & Edge Design

Quick Answer: A contact lens is specified by its central posterior curve (base curve) , peripheral curve system , total diameter , thickness profile , vertex-compensated power , and edge design . Together these determine fit, comfort, tear exchange, oxygen delivery, and optical performance.

Central Posterior Curve (CPC / Base Curve)

The central posterior curve (CPC) , or base curve (BC) , is the primary fitting curve that conforms to the cornea. It can be expressed in:

  • Millimeters of radius (e.g., 8.4 mm) — RGP, scleral, and many soft lenses
  • Diopters (e.g., 42.50 D) — using r(mm) = 337.5 / K(D)

A steep cornea (e.g., 45.00 D = 7.50 mm radius) needs a steeper (lower radius) BC; a flat cornea (e.g., 42.00 D = 8.04 mm) needs a flatter BC.

  • Soft lens BC selection : typically 0.3–0.8 mm flatter than flat-K, to allow sagittal draping over the cornea
  • RGP BC selection : on-K to 0.25 D steeper than flat-K, with a tear lens calculation built into final power
  • Peripheral Curves (IPC, PPC)

RGPs use a multi-curve back surface: central (BC) + secondary + intermediate + peripheral curves .

Intermediate peripheral curve (IPC) — slightly steeper than BC, smooths the transition from central to periphery

Peripheral peripheral curve (PPC) — flatter than BC, creates edge lift for tear exchange

A well-designed peripheral system creates a tear pump that flushes debris and metabolic waste with each blink. The classic "three-point touch" pattern (apical touch, mid-peripheral clearance, peripheral bearing) is the goal of a well-fit RGP. The peripheral curve width is typically 0.4–0.8 mm with 0.6–0.8 mm of edge lift.

Diameter

  • Lens Type Typical Diameter
  • Soft 13.8–14.5 mm
  • RGP 8.5–9.5 mm
  • Toric soft 14.5 mm (stabilization zones)
  • Scleral / mini-scleral 14.5–18.0+ mm
  • Ortho-K 10.0–11.0 mm (center flat, reverse geometry)

Larger diameter → more sagittal depth → steeper effective fit on a soft lens. Smaller diameter RGP avoids the limbus and offers better tear exchange but more lid interaction. Diameter changes affect centration, movement, and lens-tissue interaction more than many fitters expect.

  • Thickness
  • Center thickness (ct) — primary driver of oxygen transmissibility in minus lenses
  • Edge thickness — affects comfort and lid interaction in high-plus

Lenticular designs thin the periphery (plus) or edge (minus) to reduce mass and raise Dk/t. Thickness matters because Dk/t = Dk / t — halving thickness doubles transmissibility. For high Rx patients, lens thickness is often the limiting clinical factor, not material Dk.

Power: Vertex Compensation

Power must be vertex-compensated when the refraction is taken at a 12 mm spectacle plane and the contact lens sits at the corneal plane.

  • For ≥ ±4.00 D, vertex distance matters clinically
  • Plus Rx: add plus power (spectacle +10.00 D → contact +11.25 D)
  • Minus Rx: subtract minus power (spectacle −8.00 D → contact −7.25 D)

Formula: F_cl = F_spectacle / (1 − d·F_spectacle) , where d = 0.012 m.

Vertex Compensation Table (12 mm)

  • Spectacle Power Contact Power (approx)
  • −4.00 D −3.75 D
  • −8.00 D −7.25 D
  • −12.00 D −10.50 D
  • +10.00 D +11.25 D
  • +15.00 D +18.00 D

For RGP, add the tear lens power: CLP = SLP − F_tear , where F_tear is the difference between flat-K and BC. A steeper BC (relative to flat-K) creates a plus tear lens, requiring minus power added to compensate; a flatter BC creates a minus tear lens.

Edge Design

RGP edge design influences comfort and tear exchange. The ideal edge lift is 0.6–0.8 mm .

  • Blended edge — smoothed transition; balanced comfort and tear pump
  • Sharp edge — best tear exchange, more lid awareness
  • Rounded edge — most comfortable, slightly less tear exchange

Soft lens edges come as knife-edge, rounded, or chiseled — each affects comfort, movement, and deposit tendency. A poorly designed soft-lens edge produces 3 and 9 o'clock staining and sensation on blink.

Sagittal Depth Relationship

Sagittal depth (SAG) = the height of the lens from base to apex. For a given diameter:

SAG increases with steeper BC (lower radius) and/or larger diameter.

A lens that is too steep (high SAG) → tight fit, poor movement, induced edema, blurred vision from excessive tear lens

A lens that is too flat (low SAG) → excessive movement, poor centration, edge stand-off, fluctuating vision

Scleral fitting is entirely SAG-driven — the lens must vault the cornea and limbus, then land on the sclera without compression. Fitters adjust SAG by changing diameter and/or base (scleral) curve to achieve target central clearance.

Fitting Summary Table

  • Parameter Soft Lens RGP
  • BC start 0.3–0.8 mm flatter than flat-K On-K to 0.25 D steeper
  • Diameter 13.8–14.5 mm 8.5–9.5 mm
  • Edge lift N/A (drape) 0.6–0.8 mm
  • Power Vertex compensated Vertex + tear lens
  • Tear exchange Minimal (drape) Strong (tear pump)
  • Thickness Driven by Rx and material Driven by design and Rx
  • Clinical Bottom Line

Base curve anchors the fit; convert between mm and D with r = 337.5 / D .

Peripheral curves make RGP lenses wearable — without them, tear exchange stagnates and the cornea hypoxes.

Diameter changes alter sagittal depth and centration more than many fitters expect — change diameter before abandoning a design.

Vertex every Rx ≥ ±4.00 D — a non-vertexed −12.00 D lens is ~1.50 D too much minus.

Edge design is the difference between a comfortable all-day wear and a patient who returns at hour 4 with lid awareness.