Study guide

Radiuscope, Lensometer, Thickness Gauge & ANSI Z80

NCLE CLRE Contact Lens Registry Exam Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

0.1 About the CLRE Exam 0.2 How to Use This Study Guide

2 Ocular Anatomy: Adnexa

Tear Film: Layers, Glands & Break-Up Time Conjunctiva, Lids, Lashes, Fornix & Canthi Blink Rate, Lid Function & Contact Lens Wear Effects

3 Ocular Anatomy: Anterior & Posterior Segment

Corneal Layers, Curvature, Topography & Metabolism Iris, Pupil, Sclera & Anterior Chamber Crystalline Lens, Retina, Choroid & Posterior Chamber

4 Refractive Errors & Contact Lens Optics

Myopia, Hyperopia, Astigmatism, Presbyopia & Anisometropia Refraction, Prism, Lacrimal Lens, Accommodation & Transposition Vertex Distance, Sagittal Depth & Spherical Equivalent

5 Measurement Instrumentation

Keratometer/Ophthalmometer: Calibration, Readings & Interpretation Corneal Topography & OCT for Contact Lens Fitting Schirmer Tests & Tear Break-Up Time

6 Observation & Verification Instrumentation

Slit Lamp (Biomicroscope) Operation & Illumination Slit Lamp Evaluation With & Without Contact Lenses Radiuscope, Lensometer, Thickness Gauge & ANSI Z80

7 Prefitting Patient Evaluation

6.1 Lifestyle, Occupation, Environment & Motivation 6.2 Medical History, Diseases, Medications & Allergies 6.3 Contraindications & Factors for Successful Wear 6.4 Relating Corneal Measurements, Rx & Lens Parameters

8 Lens Materials, Design & Parameter Selection

Dk, Dk/t, Thermal Conductivity & Holden-Mertz Water Content, Wetting Angle, Modulus, Silicone Hydrogel & Surface Treatments Toric, Multifocal, Aspheric, Hybrid, Scleral, Orthokeratology & Quadrant-Specific Base Curve, Peripheral Curves, Diameter, Thickness, Power & Edge Design

9 Diagnostic Fitting Procedures

8.1 Lens Selection & Application Procedures 8.2 Fluorescein Pattern Evaluation for RGP Lenses 8.3 Soft Lens Movement, Centration & Coverage

10 Fit Evaluation & Over-Refraction

Toric Lens Axis Rotation, LARS Rule & Stabilization Patient Comfort, Visual Acuity & Over-Refraction Modifying Base Curve, Diameter, Sag & Power from Findings

11 Dispensing: Wearing Schedules & Replacement

Daily, Flexible & Extended/Continuous Wear Schedules Daily, Biweekly, Monthly & Conventional Replacement Adaptation Protocols & Patient Compliance Counseling

12 Dispensing: Lens Care Systems

Solution Compatibility with Lens Types Chemical, Heat/UV, Hydrogen Peroxide & Neutralization Surfactant Cleaners, Protein Removers & Weekly Cleaning Solution Sensitivities, Incompatibilities & Adverse Reactions

13 Dispensing: Handling & Hygiene

12.1 Soft Lens Insertion & Removal Techniques 12.2 RGP Insertion, Removal & Emergency Responses 12.3 Hygiene, Soaps, Cosmetics & Storage Containers 12.4 Verifying Lens Parameters Against the Order at Dispensing

14 Follow-Up: Subjective & Objective Findings

13.1 Subjective Complaints: Dryness, Awareness, Blurry Vision, Pain & Photophobia 13.2 Steep vs Flat Lens Fit (Rigid & Soft) & Everted Lens 13.3 Injection, Edema, Discharge, Vision Loss & Lid Problems 13.4 Visual Acuity, Over-Refraction & Gross Evaluation Techniques

15 Follow-Up: Staining Patterns & Complications

14.1 Staining Patterns: 3 & 9 O'Clock, Foreign Body, SPK, Arcuate, Smile & Dimple Veiling 14.2 SEAL, CLARE, VLK, SLK & CLPU 14.3 Microbial Keratitis, Acanthamoeba, Dendritic Ulcer & Infiltrates 14.4 Corneal Molding/Warpage, Dellen & Mucin Balls

16 Follow-Up: Management Protocols

GPC, Blepharitis, Ptosis & Tarsal Plate Evaluation Daily Wear, Extended, Therapeutic, Postsurgical & Pathology Protocols Changing Lens Parameters at Follow-Up & Documenting Records

17 Regulatory & Administrative

FCLCA, FDA, FTC, Contact Lens Rule & Prescriber Verification HIPAA, PHI, OSHA, CDC, ANSI & Universal Precautions Record Retention, Inventory, Ordering & Documentation Methodology

Radiuscope, Lensometer, Thickness Gauge & ANSI Z80

Key Takeaways Explain This Topic AI

The radiuscope (optic spherometer) verifies the base curve (central posterior curve) of an RGP lens in millimeters using Drysdale's method, reading the difference between two focus positions (aerial image and surface object).

The lensometer verifies lens power: RGP lenses are measured in air; soft lenses must be hydrated and measured in a wet cell because the material's refractive index differs between dry and hydrated states.

The thickness gauge measures center thickness (typically ±0.02 mm tolerance); the 10x measuring magnifier (loupe with reticle) and V-gauge verify diameter and edge design.

In-office modifications (polishing, edge taper, edge blend) apply only to RGP lenses; a fluorescent tube is used to inspect edge blend uniformity, and soft lenses cannot be modified in-office.

ANSI Z80 tolerances: RGP power ±0.12 D and base curve ±0.05 mm are tighter than soft lens power ±0.25 D and diameter ±0.10 mm; RGP diameter tolerance is ±0.05 mm and center thickness ±0.02 mm for both.

Last updated: July 2026

Lens Verification Instruments & ANSI Z80

After a contact lens is fabricated or modified, it must be verified against the ordered parameters before dispensing. CLRE Domain III tests both the instruments and the tolerance standards that define an acceptable lens. The four core instruments are the radiuscope , lensometer , thickness gauge , and measuring magnifier (or diameter gauge) , and the tolerance framework is ANSI Z80 .

Radiuscope (Optic Spherometer)

The radiuscope verifies the base curve (central posterior curve, CPC) of a rigid gas permeable (RGP) lens in millimeters. It works on Drysdale's method :

The lens is placed concave side up on the stage.

A microscope objective focuses light through a small aperture onto the concave surface.

The operator focuses on two image positions in succession:

The first focus is the aerial image formed by reflection from the lens surface (the "image" position).

The second focus is the surface itself (the "object" position).

The difference between the two positions, read from the calibrated drum, equals the radius of curvature in millimeters.

For soft lenses, the radiuscope is rarely used clinically because the lens must be hydrated and measured in a wet cell; most soft lens base curves are taken from the manufacturer's label.

  • What it measures Unit Lens type Tolerance (ANSI Z80)
  • Base curve (CPC) of RGP mm RGP in air ±0.05 mm
  • Lensometer (Focimeter)

The lensometer measures lens power (sphere, cylinder, axis if any). For contact lenses, the measurement medium differs by material:

RGP lenses are measured in air , placed concave side down on the lens stop.

Soft lenses must be hydrated and measured in a wet cell — a saline-filled chamber that supports the lens and approximates on-eye conditions. Measuring a soft lens dry gives false power because the material index of refraction differs between hydrated and dehydrated states.

A standard lensometer reads power to ±0.12 D; a column or projection lensometer can be used. For toric soft lenses, the cylinder axis should be verified while the lens is properly hydrated and centered in the wet cell.

  • What it measures Unit Lens type Tolerance (ANSI Z80)
  • Sphere power Diopters RGP in air ±0.12 D (in the common range, |power| <= ±5.00 D)
  • Sphere power Diopters Soft (wet cell) ±0.25 D (in the common range, |power| <= ±5.00 D)
  • Cylinder axis Degrees Toric ±5 degrees (varies by cylinder power)
  • Thickness Gauge

The thickness gauge (often a dial-type micrometer with a rounded probe) measures center thickness of a contact lens in millimeters or hundredths of a millimeter. For soft lenses, the gauge must apply minimal pressure to avoid deforming the hydrated material and reading falsely thin. RGP lenses can be measured with firmer contact.

  • What it measures Unit Tolerance (ANSI Z80)
  • Center thickness mm (typically 0.02-0.20 mm for soft) ±0.02 mm
  • Measuring Magnifier (10x Loupe with Reticle) and Diameter Gauge

A 10x measuring magnifier (e.g., a reticle loupe) is used to inspect:

Lens diameter (compare against the reticle scale).

Edge design — blend, taper, shape; defects, nicks, and chips at the edge.

Optic zone diameter for multifocals or translating designs.

A V-gauge or template gauge can also confirm diameter by dropping the lens into the smallest slot it fits.

For soft lenses, diameter is often verified by wet measurement in a saline bath using a calibrated reticle or by templating.

In-Office Modifications

CLRE tests familiarity with RGP in-office modification tools and what they can correct:

  • Modification Tool Purpose
  • Polish surface Polisher with fine abrasive Remove deposits, scratches, haze
  • Taper edge Edge-taper tool Reduce edge thickness for comfort

Modify edge blend / bevel Blend tool Adjust the peripheral edge blend (bevel); evaluate under fluorescent tube light

Power change Pad and polish the front surface Limited power change, typically only small minus additions; not for soft lenses

The fluorescent tube is used to inspect edge blend uniformity because the diffuse UV light reveals irregularities in the blend that white light can miss. Modifications are only appropriate for RGP lenses — soft lenses cannot be modified in-office.

ANSI Z80 Tolerance Summary

The American National Standards Institute Z80 series governs ophthalmic tolerances, including contact lenses. The most-tested tolerances:

  • Parameter Soft lens tolerance RGP tolerance
  • Power (back vertex) ±0.25 D (<= ±5.00 D) ±0.12 D (<= ±5.00 D)
  • Power (higher ranges) ±2% (> ±5.00 D) ±0.18 D (> ±5.00 D)
  • Base curve (CPC) ±0.20 mm (manufacturer-verified) ±0.05 mm
  • Diameter ±0.10 mm ±0.05 mm
  • Center thickness ±0.02 mm ±0.02 mm
  • Cylinder axis ±5 degrees (typical) n/a (toric RGPs rare)
  • Optic zone ±0.20 mm ±0.10 mm

A lens outside these tolerances should be returned to the lab , not dispensed. Verify each lens before dispensing and document the results in the patient record.

Common Traps

Measuring a soft lens in air with a lensometer — it must be hydrated in a wet cell .

Measuring RGP base curve with a keratometer — a keratometer measures corneal curvature, not lens curvature; use a radiuscope .

Forgetting which tolerance is tighter — RGP tolerances (±0.12 D power, ±0.05 mm base curve) are tighter than soft lens tolerances (±0.25 D, ±0.10 mm).

Polishing a soft lens to remove deposits — in-office modification is RGP-only.

Confusing the two radiuscope focus positions — the radius is the difference between the aerial image and surface object positions.

Verification Sequence

Radiuscope — base curve (RGP only).

Lensometer — power (RGP in air; soft in wet cell).

Thickness gauge — center thickness.

Measuring magnifier / V-gauge — diameter and edge inspection.

Document all values against the lab order and ANSI tolerances; return outliers.

A contact lens that has not been verified is a clinical and legal risk. Domain III expects the candidate to know which instrument answers which parameter, what medium the lens must be in, and what tolerance defines "acceptable."