Study guide
11.3 Artifact Identification & Systematic Troubleshooting
ABRET CNIM Neurophysiologic Intraoperative Monitoring Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Eligibility Pathways & Application 1.3 Scoring, Credential Validity & Retakes
2 Neuroanatomy & Clinical Terminology for IONM
2.1 CNS Overview & Spinal Cord Tracts 2.2 Peripheral Nerves & Plexuses 2.3 Cranial Nerves Relevant to IONM 2.4 Medical & Surgical Terminology for IONM
3 Neurophysiology & Instrumentation
3.1 Evoked Potential Principles (Near/Far Field, Latency, Amplitude) 3.2 Averaging, SNR & Digital Concepts 3.3 Differential Amplifier, Filters & Montages
4 Preoperative Assessment
4.1 Surgical Plan, Diagnosis & Imaging Review 4.2 Pre-existing Conditions Affecting Monitoring 4.3 Preoperative Neuroassessment 4.4 Modality Selection by Structures at Risk
5 Equipment & Patient Setup
5.1 Equipment & Supplies Selection 5.2 Stimulating/Recording Electrodes & Impedance 5.3 Site Preparation & Electrode Application
6 Anesthesia & Physiologic Effects
6.1 Volatile Agents & Cortical Responses 6.2 TIVA, Narcotics & Neuromuscular Blockade 6.3 BP, Temperature, Hematocrit & CO2 Effects
7 Somatosensory Evoked Potentials
7.1 SSEP Pathways & Generator Sites 7.2 Upper & Lower Extremity SSEP Technique 7.3 SSEP Alert Criteria & Surgical Correlation
8 Motor Evoked Potentials
8.1 Corticospinal Pathway & TcMEP Principles 8.2 TcMEP Technique & Anesthesia Optimization 8.3 MEP Alert Criteria & Troubleshooting
9 EMG & Cortical Mapping
9.1 Free-run & Triggered EMG Principles 9.2 Cranial Nerve & Pedicle Screw EMG 9.3 Cortical Mapping & Direct Cortical Stimulation
10 BAEP, EEG & VEP
10.1 BAEP Waveforms & Technique 10.2 BAEP in CPA & Brainstem Surgery 10.3 Intraoperative EEG & Visual Evoked Potentials
11 Signal Change Recognition & Troubleshooting
11.1 Impedance Checks & Pre-incision Baselines 11.2 Surgical vs Systemic Signal Changes 11.3 Artifact Identification & Systematic Troubleshooting
12 Surgery-Specific Monitoring Protocols
12.1 Spine Surgery Monitoring Protocols 12.2 Brain & Skull Base Monitoring 12.3 Vascular, Aortic & Peripheral Nerve Protocols
13 Postoperative Phase
13.1 Electrode Removal & Sharps Safety 13.2 Cleaning, Disinfection & Infection Control 13.3 Postoperative Neuroassessment & Outcome Correlation
14 Provider Communication
14.1 Confirming the Surgical & Monitoring Plan 14.2 Patient & Caregiver Communication 14.3 Reporting Pre-incision Baselines 14.4 Real-Time Alerts & Event Communication
15 Documentation Standards
15.1 Contemporaneous Annotation of Events 15.2 Report Writing, QA & Data Management 15.3 Multidisciplinary Handoff & Continuity
16 Patient & Electrical Safety
16.1 Electrical Safety in the OR 16.2 Sterile Field, Universal Precautions & Skin Safety 16.3 Equipment Inspection & Maintenance
17 Ethics & Professional Practice
17.1 ABRET Code of Ethics, Scope & HIPAA 17.2 Contraindications, Allergies & Professional Conduct
11.3 Artifact Identification & Systematic Troubleshooting
Key Takeaways Explain This Topic AI
OR artifact (Bovie/electrosurgery, 60 Hz line noise, pumps, warmers, electrode faults) can mimic or mask true neural change—identify the signature before calling an alert
Electrosurgery typically produces high-amplitude broadband interference during active cutting/coagulation; pause averaging and resume when the field is electrically quiet
60 Hz artifact is best reduced by fixing the source (impedance, cable routing, unnecessary devices)—notch filters are a last resort because they can distort EP morphology
Use a stepwise checklist: reproduce → technical integrity → environment/noise → physiology/anesthesia → surgical correlation—without relying on proprietary 'black box' algorithms
Document artifact periods and troubleshooting steps so postoperative review can separate technical downtime from true neurologic events
Last updated: August 2026
11.3 Artifact Identification & Systematic Troubleshooting
Quick Answer: Artifacts are electrical or mechanical contaminants that look like—or hide—neural signals. Learn the signatures of electrosurgery, 60 Hz interference, and electrode faults, then troubleshoot in a fixed order: confirm the finding, verify the recording chain, quiet the environment, check physiology/anesthesia, and only then attribute change to surgery.
Intraoperative recognition fails when noise is mistaken for injury or when real injury is dismissed as "just artifact." Domain II expects a disciplined approach that any competent technologist can explain—no secret vendor algorithm required.
- Common Artifact Signatures in the OR
- Electrosurgery (Bovie / bipolar / monopolar)
Active electrosurgery injects broadband, high-amplitude noise into nearby electrodes and often saturates amplifiers. Typical behavior:
- Noise appears only while the pedal is down (or while bipolar is active)
- Traces may flat-line or show hash across many channels
- Averaging during active Bovie contaminates the average with non-neural energy
Response: Pause acquisition/averaging during heavy electrosurgery; resume when the field is quiet. Do not interpret a Bovie-contaminated average as an SSEP alert. If the surgeon must coagulate continuously during a critical window, say so: monitoring sensitivity is temporarily reduced.
Line-frequency (60 Hz) interference
In North America, 60 Hz (and harmonics) couples from AC power, warming blankets, blood warmers, surgical lights, microscopes, and poorly routed cables. Appearance:
- Rhythmic sinusoidal contamination
- Often worse with high or unbalanced electrode impedances
- May preferentially affect long lead runs parallel to power cords
Response priority (source first):
- Recheck and balance impedances
- Separate electrode leads from power cords and electrosurgery cables
- Unplug or relocate unnecessary powered devices near the head/recording sites
- Verify ground/reference integrity and headbox connections
- Consider stimulus rate choices that avoid exact locking to line frequency when your lab protocol allows
Notch filter last — a 60 Hz notch can reduce artifact but may distort EP morphology near the notch; treat it as temporary damage control, not a substitute for finding the source
Electrode and cable artifacts
- Clue Likely technical issue
- One channel wild, neighbors quiet Loose electrode, dried gel, bent needle, bad lead
- Intermittent spikes with movement Partial disconnect, strain on cable, patient motion
- All channels die at once Headbox unplugged, stimulator off, power loss, master reference lost
- Stimulus artifact huge / polarity wrong Stim cable reversed, broken return, intensity unexpectedly high
- EMG "popping" with saline irrigation Fluid bridge, electrode lift, or true irritation—correlate with field
- Other environmental noise
C-arm, intraoperative MRI/CT, ultrasonic aspirators, drills, and somatosensory stimulators from other teams can inject interference. Time your averages between bursts of equipment use when possible. Document unavoidable downtime. Artifact? → Does it track a device (Bovie on/off, warmer, C-arm)?
→ Is it one channel (electrode) or all (systemic/power)?
- → Fix source before changing interpretation rules
- Systematic Troubleshooting Sequence
Use the same order every time so you do not skip technical causes or delay surgical communication.
Step 1 — Reproduce and characterize
Is the change present on the next average/trial? Unilateral or bilateral? Which peaks/muscles? Did it begin abruptly or drift? Characterization prevents treating a single noisy sweep as cord injury.
- Step 2 — Technical integrity (recording and stimulation chain)
- Impedance check on affected channels
- Visual inspection of electrodes, tape, and connectors
- Confirm stimulator is delivering (peripheral twitch or known peripheral potential)
- Confirm correct montage, polarity, and that the intended channel is displayed
- Swap a suspect lead with a known-good spare if available
If technical failure explains the change, fix it, re-baseline if needed, and document—do not leave a false surgical alert hanging.
- Step 3 — Environmental / artifact control
- Ask whether electrosurgery is active
- Move cables; silence unnecessary devices
- Wait for imaging bursts to finish
- Avoid interpreting during known noise epochs
- Step 4 — Physiologic and anesthetic review
- MAP, temperature, EtCO₂, hematocrit/oxygenation as available
- Recent boluses, volatile changes, neuromuscular blocker redosing
- Correlate with Section 11.2 bilateral/systemic patterns
- Step 5 — Surgical correlation and communication
What maneuver is occurring?
- Communicate the pattern and your differential
- Request pause, reversal, or inspection as appropriate
- Re-acquire after intervention and report recovery or persistence
This sequence is deliberately generic. Vendor auto-alerts, proprietary SNR scores, or black-box "significance" flags may assist workflow but are not a substitute for understanding impedance, averaging, artifact signatures, and clinical correlation. On the CNIM exam, defend the physiologic and technical reasoning—not a brand-name feature.
Averaging, Filters, and Gain: Tools With Side Effects
More averages improve signal-to-noise for random noise but help less against continuous 60 Hz or Bovie hash that is time-locked or overwhelming. Do not "average away" electrosurgery.
Filter changes can clean a display while altering latency/amplitude appearance. If you change filters mid-case, document it; large unexplained morphology shifts after a filter tweak are technical until proven otherwise.
Gain/display scale changes how big a wave looks, not how big it is. Always judge alerts from measured amplitude relative to baseline, not from a zoomed screenshot.
Rejecting bad sweeps (artifact rejection) is appropriate when your system and protocol support it—rejection should remove obvious non-neural contaminants, not silently discard the very averages that show a real surgical change. Know your lab's rules.
Documentation During Troubleshooting
Annotate:
- Time artifact began and ended (for example, "Bovie 10:12–10:18—averaging paused")
- Impedance values before/after electrode replacement
- Devices relocated or unplugged
- Anesthetic/vital-sign interventions
- Surgical pauses and whether signals recovered
Postoperative questions often hinge on whether a flat period was technical downtime or a true neurologic event. Your annotations are the record.
Worked mini-scenario
Lower-extremity cortical SSEPs become unreadable during pedicle work. Free-run EMG shows intermittent spikes. Steps: (1) confirm Bovie is active—pause averages; (2) when quiet, impedance OK bilaterally; (3) MAP stable, no volatile change; (4) during screw stimulation, triggered EMG threshold is low on one screw—communicate possible breach. The "lost SSEP" during Bovie was artifact; the EMG finding was the surgical signal. Separating those threads is the skill this section trains.
Master artifact literacy and a repeatable checklist, and you will protect patients from both missed injury and unnecessary alarm fatigue—exactly what intraoperative signal-change recognition demands.