Study guide

13.2 Cleaning, Disinfection & Infection Control

ABRET CNIM Neurophysiologic Intraoperative Monitoring Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Eligibility Pathways & Application 1.3 Scoring, Credential Validity & Retakes

2 Neuroanatomy & Clinical Terminology for IONM

2.1 CNS Overview & Spinal Cord Tracts 2.2 Peripheral Nerves & Plexuses 2.3 Cranial Nerves Relevant to IONM 2.4 Medical & Surgical Terminology for IONM

3 Neurophysiology & Instrumentation

3.1 Evoked Potential Principles (Near/Far Field, Latency, Amplitude) 3.2 Averaging, SNR & Digital Concepts 3.3 Differential Amplifier, Filters & Montages

4 Preoperative Assessment

4.1 Surgical Plan, Diagnosis & Imaging Review 4.2 Pre-existing Conditions Affecting Monitoring 4.3 Preoperative Neuroassessment 4.4 Modality Selection by Structures at Risk

5 Equipment & Patient Setup

5.1 Equipment & Supplies Selection 5.2 Stimulating/Recording Electrodes & Impedance 5.3 Site Preparation & Electrode Application

6 Anesthesia & Physiologic Effects

6.1 Volatile Agents & Cortical Responses 6.2 TIVA, Narcotics & Neuromuscular Blockade 6.3 BP, Temperature, Hematocrit & CO2 Effects

7 Somatosensory Evoked Potentials

7.1 SSEP Pathways & Generator Sites 7.2 Upper & Lower Extremity SSEP Technique 7.3 SSEP Alert Criteria & Surgical Correlation

8 Motor Evoked Potentials

8.1 Corticospinal Pathway & TcMEP Principles 8.2 TcMEP Technique & Anesthesia Optimization 8.3 MEP Alert Criteria & Troubleshooting

9 EMG & Cortical Mapping

9.1 Free-run & Triggered EMG Principles 9.2 Cranial Nerve & Pedicle Screw EMG 9.3 Cortical Mapping & Direct Cortical Stimulation

10 BAEP, EEG & VEP

10.1 BAEP Waveforms & Technique 10.2 BAEP in CPA & Brainstem Surgery 10.3 Intraoperative EEG & Visual Evoked Potentials

11 Signal Change Recognition & Troubleshooting

11.1 Impedance Checks & Pre-incision Baselines 11.2 Surgical vs Systemic Signal Changes 11.3 Artifact Identification & Systematic Troubleshooting

12 Surgery-Specific Monitoring Protocols

12.1 Spine Surgery Monitoring Protocols 12.2 Brain & Skull Base Monitoring 12.3 Vascular, Aortic & Peripheral Nerve Protocols

13 Postoperative Phase

13.1 Electrode Removal & Sharps Safety 13.2 Cleaning, Disinfection & Infection Control 13.3 Postoperative Neuroassessment & Outcome Correlation

14 Provider Communication

14.1 Confirming the Surgical & Monitoring Plan 14.2 Patient & Caregiver Communication 14.3 Reporting Pre-incision Baselines 14.4 Real-Time Alerts & Event Communication

15 Documentation Standards

15.1 Contemporaneous Annotation of Events 15.2 Report Writing, QA & Data Management 15.3 Multidisciplinary Handoff & Continuity

16 Patient & Electrical Safety

16.1 Electrical Safety in the OR 16.2 Sterile Field, Universal Precautions & Skin Safety 16.3 Equipment Inspection & Maintenance

17 Ethics & Professional Practice

17.1 ABRET Code of Ethics, Scope & HIPAA 17.2 Contraindications, Allergies & Professional Conduct

13.2 Cleaning, Disinfection & Infection Control

Key Takeaways Explain This Topic AI

Reprocess reusable IONM equipment between patients using Spaulding classification and the manufacturer’s validated instructions — not improvised wipe routines

Items that penetrate skin or contact sterile tissue require high-level disinfection or sterilization; intact-skin surface gear is typically noncritical low-level disinfection

Preclean organic soil before disinfection or sterilization; skipping enzymatic/mechanical cleaning defeats chemical kill claims

Transport soiled devices in labeled leak-proof containers; store clean items dry and labeled with reprocessing status

MSDS/SDS and OSHA hazard-communication awareness guide safe use of disinfectants, collodion removers, and other chemical agents in the lab and OR

Last updated: August 2026

13.2 Cleaning, Disinfection & Infection Control

Quick Answer: After the case, reprocess reusable IONM gear by Spaulding category and manufacturer instructions — preclean organic material first, then high-level disinfect or sterilize critical/semicritical items — and know the SDS for every chemical you use.

The second Domain III postoperative task is to clean and disinfect reusable equipment per infection-control standards. Disposable needles go in sharps containers; reusable cables, boxes, stimulator probes (when reusable), surface electrode sets, and cart surfaces must not carry yesterday’s flora into today’s craniotomy. Infection control here is not housekeeping theater — it is a regulated reprocessing workflow.

Spaulding Classification Applied to IONM

The Spaulding scheme sorts devices by the body site they contact and sets the minimum reprocessing level:

Spaulding class Contact Minimum reprocessing IONM examples

Critical Sterile tissue / bloodstream Sterilization Reusable needles or probes that enter sterile tissue (follow manufacturer; many labs use single-use needles instead)

Semicritical Mucous membranes or nonintact skin High-level disinfection (HLD) or sterilization Devices contacting nonintact skin or mucosa per design

Noncritical Intact skin only Low-level disinfection Amplifier surfaces, cart handles, intact-skin surface electrode housings, cables contacting intact skin

Exam trap: Wiping a used subdermal needle with an alcohol pad does not meet critical/semicritical expectations. If a device is reusable and penetrated tissue, the manufacturer’s HLD or sterilization cycle — not a surface wipe — is required. Many programs eliminate the dilemma by using single-patient disposable needles.

Manufacturer Instructions Are Not Optional

Infection-control policy and the device IFU (instructions for use) together define the legal and safe cycle:

Temperature, chemical agent, concentration, contact time, and rinse steps are validated by the manufacturer.

Substituting a stronger “whatever is on the shelf” agent can damage plastics, leave toxic residue, or void the validated kill claim.

If the IFU says “single use,” do not reprocess — dispose.

Document cycles when your facility requires logged sterilization/HLD for reusable critical items.

When IFU and a generic OR wipe protocol conflict, escalate to infection prevention / sterile processing rather than inventing a hybrid.

Reprocessing Sequence That Actually Works

Organic load (blood, paste, tissue) inactivates many disinfectants and shields microbes. Order matters:

Point-of-use containment: Place soiled reusable items in a labeled, leak-proof biohazard transport container — not an open tray on the breakroom counter.

Preclean: Enzymatic soak, brushing, and ultrasonic cleaning when the manufacturer recommends them; remove visible soil.

Rinse: Clear detergent/enzymatic residue that would interfere with the next chemical step.

HLD or sterilization: Autoclave, ethylene oxide, hydrogen peroxide systems, or chemical sterilant/HLD per IFU.

Final rinse/dry (as required): Especially after chemical HLD; residual sterilant on a patient-contact surface is a chemical injury risk.

Package, label, store: Dated reprocessing tag, clean dry storage, protected from recontamination.

Reuse only when the cycle is complete — “it looks clean” is not a cycle. Soiled use → leak-proof transport → preclean (enzymatic/mechanical)

→ rinse → HLD or sterilize (IFU) → rinse/dry → label/store → reuse

Skipping preclean before sterilization is a classic failure mode: protein soil prevents sterilant contact with the device surface.

What Stays in the OR vs What Goes to SPD

Not every IONM item travels to sterile processing:

Cart and amplifier exteriors: Low-level disinfectant wipes compatible with electronics; avoid soaking connectors.

Cables and lead wires: Wipe per IFU; inspect for cracks that harbor fluid and fail electrical safety.

Reusable surface electrode sets: Clean of paste, then disinfect at the level appropriate to intact-skin use unless contaminated with blood in a way your policy upgrades.

Reusable sterile-field instruments: Usually return through scrub/SPD pathways with other surgical instruments.

Separate clean and dirty zones on your cart. Placing a “cleaned” cable back onto a blood-spattered shelf recontaminates it instantly.

Single-Use vs Reusable Culture

Modern IONM practice leans heavily on disposable subdermal needles because reprocessing critical sharps is operationally hard and injury-prone. That choice is an infection-control decision as much as a convenience decision. If your lab still reuses any critical item, treat the full sterilization pathway as non-negotiable and track device integrity (bent shafts, damaged insulation) — damaged devices are removed from service, not “cleaned harder.”

Chemical Safety: MSDS/SDS and OSHA Awareness

Disinfectants, collodion and removers, abrasive preps, and enzymatic cleaners are hazardous chemicals under OSHA’s Hazard Communication Standard. Practical expectations for the CNIM technologist:

Know where Safety Data Sheets (SDS; historically MSDS) live for products you use — physical binder or electronic system.

Read hazard pictograms, PPE requirements, ventilation needs, and first-aid measures before a splash occurs.

Use eye protection and gloves appropriate to the agent; some solvents require more than a thin exam glove.

Store chemicals in labeled containers; never decant into unlabeled water bottles.

Spill response: contain, notify, follow SDS and facility spill protocol — do not mop unknown solvent with dry paper towels in a closed scrub sink area without checking flammability/ventilation guidance.

Infection control and chemical safety intersect: an agent strong enough for HLD is strong enough to injure eyes and airways if misused.

Hand Hygiene and Standard Precautions

Reprocessing does not replace personal practices:

Gloves for teardown and cleaning; remove gloves and perform hand hygiene before touching clean keyboards, door handles, or your phone.

Treat all blood and body fluids with standard precautions regardless of known patient diagnosis.

Do not eat or drink on the soiled cart.

Report device contamination events that may have exposed the sterile field so infection prevention can assess patient risk.

Quality and Turnover Pressure

OR turnover pressure tempts shortcuts: a quick wipe of a bloody reusable probe, skipping contact time, or returning an item to the clean drawer while still wet with disinfectant. Those shortcuts create false security. If time is insufficient for a full cycle, use a sterile/disposable alternative or delay the next case’s use of that device — do not invent a two-minute sterilization.

  • Key Takeaways
  • Match reprocessing level to Spaulding class and the manufacturer IFU
  • Preclean before HLD/sterilization; soil defeats chemistry
  • Transport soiled gear in labeled leak-proof containers; keep clean/dirty separation

Prefer single-use criticals when policy allows; never wipe-reprocess tissue-penetrating needles as if they were noncritical

SDS/MSDS literacy and PPE are part of infection-control competence, not optional reading