Study guide

10.4 Practical Enclosure & Raceway Sizing Exam Scenarios

Colorado Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Colorado Electrical Licensing Laws, DORA Rules & Exam Logistics

1.1 Colorado Electrical Board, Licensure Tiers & Application Process 1.2 Senate Bill 25-165, Apprentice Supervision & Colorado Board Rules 1.3 Permitting, Inspection Procedures, Violations & Penalties 1.4 The Colorado PSI Exam: Open-Book Format, Time Management & Code Navigation

2 Chapter 2: Electrical Theory, Mathematics & Fundamental Concepts

2.1 Ohm's Law, Joule's Law & DC Circuit Analysis 2.2 AC Fundamentals: Inductance, Capacitance & Power Factor 2.3 Three-Phase Electrical Systems: Wye & Delta Configurations 2.4 Voltage Drop Principles & Single/Three-Phase Formulas

3 Chapter 3: General Installation Requirements — NEC Articles 90 & 110

3.1 NEC Structure, Arrangement & Article 90 Fundamentals 3.2 Key Article 100 Definitions for the Exam 3.3 Equipment Examination, Listing & Termination Temperature Limits 3.4 Working Space, Dedicated Electrical Space & Guarding

4 Chapter 4: Branch Circuits & Feeders — NEC Articles 210, 215 & 225

4.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Branch Circuits 4.2 Dwelling Unit Required Outlets & Receptacle Placement 4.3 Ground-Fault Circuit-Interrupter (GFCI) Protection 4.4 Arc-Fault Circuit-Interrupter (AFCI) Protection & Feeder Rules

5 Chapter 5: Services & Overcurrent Protection — NEC Articles 230, 240 & 242

5.1 Service Conductors, Clearances & Overhead/Underground Drops 5.2 Service Disconnecting Means, Ratings & Surge Protection 5.3 Overcurrent Protection Fundamentals & Standard Ratings 5.4 Feeder & Transformer Tap Rules

6 Chapter 6: Grounding and Bonding — NEC Article 250 Part I (Systems & Electrodes)

6.1 Grounding vs. Bonding: Principles, Functions & Article 250 Architecture 6.2 Grounded Conductors, Main Bonding Jumpers & System Bonding Jumpers 6.3 The Grounding Electrode System 6.4 Grounding Electrode Conductor (GEC) Sizing & Installation

7 Chapter 7: Grounding and Bonding — NEC Article 250 Part II (Equipment & Special Systems)

7.1 Equipment Grounding Conductors (EGC) Types & Identification 7.2 Sizing the Equipment Grounding Conductor 7.3 Separately Derived Systems 7.4 Grounding & Bonding at Separate Buildings or Structures

8 Chapter 8: Wiring Methods & Materials — NEC Chapter 3

8.1 General Wiring Requirements & Underground Installations 8.2 Nonmetallic and Armored Cable Assemblies 8.3 Metallic and Nonmetallic Raceways 8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways

9 Chapter 9: Conductors, Ampacity & Wire Sizing — NEC Article 310

9.1 Conductor Properties, Insulation Types & NEC Table 310.16 9.2 Temperature Correction Factors 9.3 Conductor Bundling & Adjustment Factors 9.4 Comprehensive Conductor Sizing & Terminal Temperature Coordination

10 Chapter 10: Box Fill, Conduit Fill & Pull Box Calculations

10.1 Outlet and Device Box Fill Calculations — NEC 314.16(A) & (B) 10.2 Conduit Fill Calculations — Chapter 9 Tables 1, 4, 5 & Annex C 10.3 Pull and Junction Box Sizing for Conductors 4 AWG and Larger — NEC 314.28 10.4 Practical Enclosure & Raceway Sizing Exam Scenarios

11 Chapter 11: Load Calculations — Dwellings & Commercial Buildings — NEC Article 120

11.1 General Lighting, Small Appliance & Laundry Loads 11.2 Fixed Appliances, Dryers & Cooking Equipment Calculations 11.3 Standard vs. Optional Calculation Methods for Single-Family Dwellings 11.4 Commercial & Multifamily Load Calculations

12 Chapter 12: Motors, Motor Circuits & Controllers — NEC Article 430

12.1 Motor Nameplate vs. NEC Tables & Motor Full-Load Current 12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection 12.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 12.4 Motor Feeders, Disconnecting Means & Controllers

13 Chapter 13: Transformers, Distribution & Utilization Equipment

13.1 Transformer Overcurrent Protection & Installation — NEC Article 450 13.2 Panelboards, Switchboards & Switchgear — NEC Article 408 13.3 Luminaires, Appliances & Fixed Electric Space Heating 13.4 Generators, Transfer Switches & Standby Systems

14 Chapter 14: Special Occupancies, Renewable Energy & Modern Technologies

14.1 Hazardous (Classified) Locations — NEC Articles 500-516 14.2 Health Care Facilities & Places of Assembly — NEC Articles 517 & 518 14.3 Swimming Pools, Spas, Hot Tubs & Fountains — NEC Article 680 14.4 Solar Photovoltaic (PV) Systems & Energy Storage — NEC Articles 690, 705 & 706

10.4 Practical Enclosure & Raceway Sizing Exam Scenarios

Key Takeaways Explain This Topic AI

Complex multi-gang box calculations require categorizing conductors by gauge size, applying device allowances to the largest connected wire, and attributing clamp and EGC allowances to the largest conductor in the box.

When sizing conduit for commercial feeders, cross-sectional areas of insulated conductors (Table 5) and bare grounding conductors (Table 8) must be summed and matched against Table 4's 40% column.

Pull box calculations require independent evaluations for each entry wall (height vs. width) and verification that diagonal spacing between entries of the same conductor satisfies the 6× rule.

Adding the cubic-inch capacity of a raised plaster ring or extension ring to a standard metal box is often the key to achieving code compliance without tearing out wall studs.

Conduit fill calculations must always include bare equipment grounding conductors even though they are excluded from current-carrying conductor bundling derating.

Last updated: September 2026

10.4 Practical Enclosure & Raceway Sizing Exam Scenarios

Exam Fast Fact: The Colorado Journeyman Electrician examination, administered by PSI, deliberately tests candidate competence by combining multiple code articles into single, multi-step calculation scenarios. On raceway and box sizing questions, exam writers routinely combine mixed conductor gauges, both bare and insulated wires, internal clamps, devices with different terminal sizes, and plaster ring extensions. Mastering how to dissect these comprehensive scenarios step-by-step guarantees full points on this section of the examination.

To achieve confidence on exam day, candidates must transition from reviewing isolated code rules to executing end-to-end calculations under exam time constraints. This section walks through four comprehensive real-world scenarios designed to mirror the exact structure, phrasing, and difficulty of the Colorado Journeyman examination.

  • Problem 1: Multi-Gang Device Box with Mixed Wiring & Devices
  • Exam Problem Statement

An electrician is roughing in a two-gang metallic device box in a commercial breakroom. The box installation contains the following items:

  • Two 14/2 with ground Type NM-B cables entering through the top
  • One 14/3 with ground Type NM-B cable entering through the top
  • Two 12/2 with ground Type NM-B cables entering through the bottom
  • The metal box contains factory-installed internal cable clamps
  • Device 1: A single-pole toggle switch controlling lighting, connected to 14 AWG conductors
  • Device 2: A 20-ampere commercial GFCI duplex receptacle, connected to 12 AWG conductors
  • All equipment grounding conductors are spliced together with two ground pigtails connected to the devices

Question: What is the minimum total internal volume in cubic inches required for this two-gang installation under NEC 314.16 ? PROBLEM 1 CALCULATION BREAKDOWN

  • (NEC 314.16)
  • ┌─────────────────────────────────┬───────┬────────────┬─────────────┐
  • │ Item Category │ Count │ Rate/Unit │ Total (cu.) │
  • ├─────────────────────────────────┼───────┼────────────┼─────────────┤
  • │ 14 AWG Insulated Conductors │ 7 │ 2.00 cu in │ 14.00 cu in │
  • │ 12 AWG Insulated Conductors │ 4 │ 2.25 cu in │ 9.00 cu in │
  • │ Internal Cable Clamps │ 1 │ 2.25 cu in │ 2.25 cu in │
  • │ Switch Device (on 14 AWG) │ 2 │ 2.00 cu in │ 4.00 cu in │
  • │ GFCI Receptacle (on 12 AWG) │ 2 │ 2.25 cu in │ 4.50 cu in │
  • │ First 4 Grounding Conductors │ 1 │ 2.25 cu in │ 2.25 cu in │
  • │ 5th Grounding Conductor │ 1/4 │ 2.25 cu in │ 0.56 cu in │
  • │ Pigtails (Grounds/Neutrals) │ 0 │ 0.00 cu in │ 0.00 cu in │
  • ├─────────────────────────────────┴───────┴────────────┼─────────────┤
  • │ TOTAL MINIMUM VOLUME REQUIRED │ 36.56 cu in │
  • └──────────────────────────────────────────────────────┴─────────────┘
  • Detailed Mathematical Solution

Insulated Conductor Count (NEC 314.16(B)(1)):

  • Two 14/2 cables = 4 conductors (2 black, 2 white)
  • One 14/3 cable = 3 conductors (1 black, 1 red, 1 white)

Total 14 AWG conductors = 4 + 3 = 7 4 + 3 = 7 4 + 3 = 7 conductors.

Volume for 14 AWG: 7 × 2.00 cu. in. = 14.00 cu. in. 7 \times 2.00\text{ cu. in.} = \mathbf{14.00\text{ cu. in.}} 7 × 2.00 cu. in. = 14.00 cu. in.

Two 12/2 cables = 4 conductors (2 black, 2 white)

Volume for 12 AWG: 4 × 2.25 cu. in. = 9.00 cu. in. 4 \times 2.25\text{ cu. in.} = \mathbf{9.00\text{ cu. in.}} 4 × 2.25 cu. in. = 9.00 cu. in.

Internal Cable Clamps (NEC 314.16(B)(2)):

The box contains internal clamps. Under the code, all internal clamps collectively count as one single volume allowance based on the largest conductor in the box (12 AWG).

Volume for Clamps: 1 × 2.25 cu. in. = 2.25 cu. in. 1 \times 2.25\text{ cu. in.} = \mathbf{2.25\text{ cu. in.}} 1 × 2.25 cu. in. = 2.25 cu. in.

Devices / Equipment (NEC 314.16(B)(4)):

Each yoke or strap counts as two volume allowances based on the largest conductor connected to that device.

Switch (connected to 14 AWG): 2 × 2.00 cu. in. = 4.00 cu. in. 2 \times 2.00\text{ cu. in.} = \mathbf{4.00\text{ cu. in.}} 2 × 2.00 cu. in. = 4.00 cu. in.

GFCI Receptacle (connected to 12 AWG): 2 × 2.25 cu. in. = 4.50 cu. in. 2 \times 2.25\text{ cu. in.} = \mathbf{4.50\text{ cu. in.}} 2 × 2.25 cu. in. = 4.50 cu. in.

Equipment Grounding Conductors (NEC 314.16(B)(5)):

Count the total number of EGCs entering the box:

  • Two 14 AWG bare wires (from the two 14/2 cables)
  • One 14 AWG bare wire (from the 14/3 cable)
  • Two 12 AWG bare wires (from the two 12/2 cables)

Total EGCs entering = 2 + 1 + 2 = 5 grounding conductors 2 + 1 + 2 = \mathbf{5\text{ grounding conductors}} 2 + 1 + 2 = 5 grounding conductors .

Code Rule: Up to four EGCs count as one allowance based on the largest EGC (12 AWG = 2.25 cu. in.).

For each additional EGC beyond four, add 1/4 (0.25) allowance , also based on the largest EGC.

Allowance for first 4 EGCs = 1 × 2.25 cu. in. = 2.25 cu. in. 1 \times 2.25\text{ cu. in.} = 2.25\text{ cu. in.} 1 × 2.25 cu. in. = 2.25 cu. in.

Allowance for 5th EGC = 0.25 × 2.25 cu. in. = 0.5625 cu. in. 0.25 \times 2.25\text{ cu. in.} = 0.5625\text{ cu. in.} 0.25 × 2.25 cu. in. = 0.5625 cu. in.

Total Grounding Volume: 2.25 + 0.5625 = 2.8125 cu. in. 2.25 + 0.5625 = \mathbf{2.8125\text{ cu. in.}} 2.25 + 0.5625 = 2.8125 cu. in.

Pigtails and Wire Connectors:

Conductor pigtails originating and terminating entirely within the enclosure count as zero allowances .

Total Box Volume Required: Total Volume = 14.00 + 9.00 + 2.25 + 4.00 + 4.50 + 2.8125 = 36.5625 cubic inches \text{Total Volume} = 14.00 + 9.00 + 2.25 + 4.00 + 4.50 + 2.8125 = \mathbf{36.5625\text{ cubic inches}} Total Volume = 14.00 + 9.00 + 2.25 + 4.00 + 4.50 + 2.8125 = 36.5625 cubic inches

Field Selection Solution: A standard 4" × 2-1/8" square box has 30.3 cu. in. (insufficient). Adding a two-gang raised plaster ring marked with 6.5 cu. in. provides 30.3 + 6.5 = 36.8 cu. in. 30.3 + 6.5 = 36.8\text{ cu. in.} 30.3 + 6.5 = 36.8 cu. in. , successfully meeting the 36.56 cu. in. requirement.

  • Problem 2: Sizing an EMT Feeder Raceway for a Subpanel
  • Exam Problem Statement

An electrician must size an Electrical Metallic Tubing (EMT) raceway for a commercial distribution subpanel feeder. The conduit run exceeds 24 inches and contains:

  • Three 4/0 AWG copper conductors with Type THHN insulation (un在此 phase legs)
  • One 2/0 AWG copper conductor with Type THHN insulation (neutral conductor)
  • One 4 AWG bare stranded copper equipment grounding conductor

Question: Using NEC Chapter 9 Tables 4, 5, and 8, what is the minimum trade size EMT required? PROBLEM 2 CONDUIT FILL SIZING

(CHAPTER 9)

1. LOOK UP CROSS-SECTIONAL AREAS:

• 4/0 AWG THHN (Table 5) = 0.3237 sq. in. × 3 = 0.9711 sq. in.

• 2/0 AWG THHN (Table 5) = 0.2223 sq. in. × 1 = 0.2223 sq. in.

• 4 AWG Bare Stranded (Table 8) = 0.0484 sq. in. × 1 = 0.0484 sq. in.

2. CALCULATE TOTAL CONDUCTOR AREA:

Total Area = 0.9711 + 0.2223 + 0.0484 = 1.2418 sq. in.

3. CHECK CHAPTER 9 TABLE 4 (EMT 40% FILL):

  • 1-1/2" EMT 40% Area = 0.814 sq. in. (0.814 < 1.2418 ──> TOO SMALL)
  • 2" EMT 40% Area = 1.342 sq. in. (1.342 ≥ 1.2418 ──> COMPLIANT!)
  • Detailed Mathematical Solution

Identify Conductor Properties & Areas:

4/0 AWG THHN from Chapter 9 Table 5: Area = 0.3237 sq. in. Total phase conductor area = 3 × 0.3237 = 0.9711 sq. in. 3 \times 0.3237 = \mathbf{0.9711\text{ sq. in.}} 3 × 0.3237 = 0.9711 sq. in.

2/0 AWG THHN from Chapter 9 Table 5: Area = 0.2223 sq. in. Total neutral conductor area = 1 × 0.2223 = 0.2223 sq. in. 1 \times 0.2223 = \mathbf{0.2223\text{ sq. in.}} 1 × 0.2223 = 0.2223 sq. in.

4 AWG bare stranded copper from Chapter 9 Table 8: Area = 0.0484 sq. in. Total grounding conductor area = 1 × 0.0484 = 0.0484 sq. in. 1 \times 0.0484 = \mathbf{0.0484\text{ sq. in.}} 1 × 0.0484 = 0.0484 sq. in.

Sum All Conductor Areas: Total Conductor Area = 0.9711 + 0.2223 + 0.0484 = 1.2418 square inches \text{Total Conductor Area} = 0.9711 + 0.2223 + 0.0484 = \mathbf{1.2418\text{ square inches}} Total Conductor Area = 0.9711 + 0.2223 + 0.0484 = 1.2418 square inches

Determine Permitted Raceway Fill:

Total number of conductors = 3 + 1 + 1 = 5 3 + 1 + 1 = 5 3 + 1 + 1 = 5 conductors.

Under Chapter 9 Table 1, raceways containing 3 or more conductors are limited to 40% fill .

Evaluate Trade Sizes from Chapter 9 Table 4 (EMT):

Trade Size 1-1/2" EMT: 40% area = 0.814 sq. in. 0.814\text{ sq. in.} 0.814 sq. in. Since 0.814 < 1.2418 0.814 < 1.2418 0.814 < 1.2418 , 1-1/2" is too small.

Trade Size 2" EMT: 40% area = 1.342 sq. in. 1.342\text{ sq. in.} 1.342 sq. in. Since 1.342 ≥ 1.2418 1.342 \ge 1.2418 1.342 ≥ 1.2418 , 2" EMT is the minimum compliant trade size.

  • Problem 3: Dimensioning a Commercial Pull Box (Straight vs. Angle Pull)
  • Exam Problem Statement

A commercial junction box contains 500 kcmil conductors (larger than 4 AWG). Conduits enter and exit the enclosure under two distinct configurations:

Configuration A (Straight Pull):

Left wall: One 3" conduit, two 2" conduits, one 1" conduit.

Right wall: All conduits exit straight through the opposite wall.

Question: What is the minimum length required between the left and right walls?

Configuration B (Angle Pull):

Left wall: One 3" conduit, two 2" conduits, one 1" conduit enter.

Bottom wall: One 3" conduit, two 2" conduits, one 1" conduit exit at 90 degrees.

Question: What are the minimum dimensions (Width and Height) and minimum entry separation? PROBLEM 3 CONFIGURATION COMPARISON

  • CONFIGURATION A: STRAIGHT PULL CONFIGURATION B: ANGLE PULL
  • L = 8 × D_largest L = (6 × D_largest) + Sum(D_other)
  • L = 8 × 3" = 24 Inches L = (6 × 3") + 2" + 2" + 1" = 23 Inches
  • 3" ───> ═══════════> ───> 3" 3" ───╮
  • 2" ───> ═══════════> ───> 2" 2" ───┼──╮
  • 2" ───> ═══════════> ───> 2" 2" ───┼──┼──╮
  • 1" ───> ═══════════> ───> 1" 1" ───┼──┼──┼──╮
  • [ 24 Inches ] │ │ │ │
  • ▼ ▼ ▼ ▼
  • 3" 2" 2" 1"
  • Detailed Mathematical Solution

Configuration A: Straight Pull (NEC 314.28(A)(1)):

  • Formula: Length = 8 × D largest \text{Length} = 8 \times D_{\text{largest}} Length = 8 × D largest ​
  • Largest conduit = 3"

Length = 8 × 3 " = 24 inches 8 \times 3" = \mathbf{24\text{ inches}} 8 × 3" = 24 inches .

Note: The two 2" conduits and the 1" conduit are completely disregarded in calculating straight pull length.

Configuration B: Angle Pull (NEC 314.28(A)(2)):

Width (Left to Right Wall):

  • Largest conduit on Left Wall = 3"
  • Other conduits on Left Wall = 2" + 2" + 1" = 5"

Distance = ( 6 × 3 " ) + ( 2 " + 2 " + 1 " ) = 18 " + 5 " = 23 inches (6 \times 3") + (2" + 2" + 1") = 18" + 5" = \mathbf{23\text{ inches}} ( 6 × 3" ) + ( 2" + 2" + 1" ) = 18" + 5" = 23 inches

Height (Bottom to Top Wall):

  • Largest conduit on Bottom Wall = 3"
  • Other conduits on Bottom Wall = 2" + 2" + 1" = 5"

Distance = ( 6 × 3 " ) + ( 2 " + 2 " + 1 " ) = 18 " + 5 " = 23 inches (6 \times 3") + (2" + 2" + 1") = 18" + 5" = \mathbf{23\text{ inches}} ( 6 × 3" ) + ( 2" + 2" + 1" ) = 18" + 5" = 23 inches

Separation Between 3" Entries:

Center-to-center diagonal distance ≥ 6 × 3 " = 18 inches \ge 6 \times 3" = \mathbf{18\text{ inches}} ≥ 6 × 3" = 18 inches .

Result: Box must be at least 23" Wide × 23" High with 18" center-to-center separation between the 3" conduit entries.

The Four Major Colorado PSI Exam Traps THE FOUR BIGGEST PSI EXAM TRAPS

  • ┌───┬───────────────────────────────┬────────────────────────────────────────┐
  • │ # │ The Common Mistake │ The Absolute Code Reality │
  • ├───┼───────────────────────────────┼────────────────────────────────────────┤
  • │ 1 │ Conductor Volume Mixing │ Calculate each wire size individually! │
  • │ │ Error (314.16) │ Only clamps, fittings, & EGCs use max. │
  • ├───┼───────────────────────────────┼────────────────────────────────────────┤
  • │ 2 │ Forgetting Plaster Ring │ Plaster ring marked volume ADDS to the │
  • │ │ Volume Capacity │ metal box cubic-inch volume! │
  • ├───┼───────────────────────────────┼────────────────────────────────────────┤
  • │ 3 │ Angle Pull Addition Error │ ONLY add other raceways entering the │
  • │ │ (314.28) │ SAME wall and row—never opposite wall! │
  • ├───┼───────────────────────────────┼────────────────────────────────────────┤
  • │ 4 │ Omitting Grounding Conductor │ Bare EGCs ALWAYS occupy raceway space; │
  • │ │ in Conduit Fill (Chapter 9) │ Look up area in Chapter 9 Table 8! │
  • └───┴───────────────────────────────┴────────────────────────────────────────┘
  • Trap 1: The Conductor Volume Mixing Error

When a box contains mixed wire sizes (such as 14 AWG and 12 AWG), candidates often apply the larger 12 AWG volume allowance (2.25 cu. in.) across all insulated conductors. This is wrong. Each insulated conductor takes the specific volume allowance of its individual gauge from Table 314.16(B). Only the internal clamps, fixture studs, and equipment grounding conductors default to the largest wire size in the box.

Trap 2: Forgetting Plaster Ring Volume

When calculating whether a 4" square metal box can accommodate a device installation, candidates often look only at the 21.0 cu. in. of a standard 4" × 1-1/2" box and conclude it violates the code. In commercial construction, mud rings add 3.0 to 9.0 cu. in. Always check whether the exam question mentions a raised plaster ring or domed cover.

Trap 3: The Angle Pull Addition Trap

In angle pull calculations under NEC 314.28(A)(2), candidates frequently add up all conduits entering the entire enclosure. The formula explicitly states that you multiply 6 times the largest raceway on that wall, plus the other raceways entering that same wall . If three conduits enter the left wall and three conduits exit the bottom wall, the left-to-right dimension depends strictly on the three conduits on the left wall.

Trap 4: Conduit Fill Overlooking the Equipment Grounding Conductor

Candidates frequently confuse the bundling derating rules of NEC 310.15 with the physical fill rules of Chapter 9. For ampacity derating under 310.15(C)(1), equipment grounding conductors do not count because they do not carry continuous current. However, for physical conduit fill under Chapter 9, bare or insulated grounding conductors occupy physical space and must always be included using Chapter 9 Table 5 or Table 8!