Study guide
9.2 Temperature Correction Factors
Colorado Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Colorado Electrical Licensing Laws, DORA Rules & Exam Logistics
1.1 Colorado Electrical Board, Licensure Tiers & Application Process 1.2 Senate Bill 25-165, Apprentice Supervision & Colorado Board Rules 1.3 Permitting, Inspection Procedures, Violations & Penalties 1.4 The Colorado PSI Exam: Open-Book Format, Time Management & Code Navigation
2 Chapter 2: Electrical Theory, Mathematics & Fundamental Concepts
2.1 Ohm's Law, Joule's Law & DC Circuit Analysis 2.2 AC Fundamentals: Inductance, Capacitance & Power Factor 2.3 Three-Phase Electrical Systems: Wye & Delta Configurations 2.4 Voltage Drop Principles & Single/Three-Phase Formulas
3 Chapter 3: General Installation Requirements — NEC Articles 90 & 110
3.1 NEC Structure, Arrangement & Article 90 Fundamentals 3.2 Key Article 100 Definitions for the Exam 3.3 Equipment Examination, Listing & Termination Temperature Limits 3.4 Working Space, Dedicated Electrical Space & Guarding
4 Chapter 4: Branch Circuits & Feeders — NEC Articles 210, 215 & 225
4.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Branch Circuits 4.2 Dwelling Unit Required Outlets & Receptacle Placement 4.3 Ground-Fault Circuit-Interrupter (GFCI) Protection 4.4 Arc-Fault Circuit-Interrupter (AFCI) Protection & Feeder Rules
5 Chapter 5: Services & Overcurrent Protection — NEC Articles 230, 240 & 242
5.1 Service Conductors, Clearances & Overhead/Underground Drops 5.2 Service Disconnecting Means, Ratings & Surge Protection 5.3 Overcurrent Protection Fundamentals & Standard Ratings 5.4 Feeder & Transformer Tap Rules
6 Chapter 6: Grounding and Bonding — NEC Article 250 Part I (Systems & Electrodes)
6.1 Grounding vs. Bonding: Principles, Functions & Article 250 Architecture 6.2 Grounded Conductors, Main Bonding Jumpers & System Bonding Jumpers 6.3 The Grounding Electrode System 6.4 Grounding Electrode Conductor (GEC) Sizing & Installation
7 Chapter 7: Grounding and Bonding — NEC Article 250 Part II (Equipment & Special Systems)
7.1 Equipment Grounding Conductors (EGC) Types & Identification 7.2 Sizing the Equipment Grounding Conductor 7.3 Separately Derived Systems 7.4 Grounding & Bonding at Separate Buildings or Structures
8 Chapter 8: Wiring Methods & Materials — NEC Chapter 3
8.1 General Wiring Requirements & Underground Installations 8.2 Nonmetallic and Armored Cable Assemblies 8.3 Metallic and Nonmetallic Raceways 8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways
9 Chapter 9: Conductors, Ampacity & Wire Sizing — NEC Article 310
9.1 Conductor Properties, Insulation Types & NEC Table 310.16 9.2 Temperature Correction Factors 9.3 Conductor Bundling & Adjustment Factors 9.4 Comprehensive Conductor Sizing & Terminal Temperature Coordination
10 Chapter 10: Box Fill, Conduit Fill & Pull Box Calculations
10.1 Outlet and Device Box Fill Calculations — NEC 314.16(A) & (B) 10.2 Conduit Fill Calculations — Chapter 9 Tables 1, 4, 5 & Annex C 10.3 Pull and Junction Box Sizing for Conductors 4 AWG and Larger — NEC 314.28 10.4 Practical Enclosure & Raceway Sizing Exam Scenarios
11 Chapter 11: Load Calculations — Dwellings & Commercial Buildings — NEC Article 120
11.1 General Lighting, Small Appliance & Laundry Loads 11.2 Fixed Appliances, Dryers & Cooking Equipment Calculations 11.3 Standard vs. Optional Calculation Methods for Single-Family Dwellings 11.4 Commercial & Multifamily Load Calculations
12 Chapter 12: Motors, Motor Circuits & Controllers — NEC Article 430
12.1 Motor Nameplate vs. NEC Tables & Motor Full-Load Current 12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection 12.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 12.4 Motor Feeders, Disconnecting Means & Controllers
13 Chapter 13: Transformers, Distribution & Utilization Equipment
13.1 Transformer Overcurrent Protection & Installation — NEC Article 450 13.2 Panelboards, Switchboards & Switchgear — NEC Article 408 13.3 Luminaires, Appliances & Fixed Electric Space Heating 13.4 Generators, Transfer Switches & Standby Systems
14 Chapter 14: Special Occupancies, Renewable Energy & Modern Technologies
14.1 Hazardous (Classified) Locations — NEC Articles 500-516 14.2 Health Care Facilities & Places of Assembly — NEC Articles 517 & 518 14.3 Swimming Pools, Spas, Hot Tubs & Fountains — NEC Article 680 14.4 Solar Photovoltaic (PV) Systems & Energy Storage — NEC Articles 690, 705 & 706
9.2 Temperature Correction Factors
Key Takeaways Explain This Topic AI
Conductor allowable ampacities in NEC Table 310.16 are based on a standard ambient baseline temperature of 30°C (86°F); operating in any ambient condition other than 30°C requires multiplying table ampacity by an ambient temperature correction factor.
When ambient temperatures exceed 30°C (86°F), heat dissipation from the conductor is impeded, requiring allowable ampacity to be derated to prevent thermal degradation of the insulation.
Colorado's semi-arid, high-altitude climate produces intense solar thermal loading on commercial flat roofs and extreme attic temperatures exceeding 120°F (49°C), triggering substantial derating.
Under NEC 310.15(B)(2), raceways installed less than 7/8 inch above a rooftop exposed to direct sunlight require a 33°C (60°F) temperature adder to be added to the outdoor design temperature; elevating the raceway at least 7/8 inch completely eliminates this adder.
Cold ambient temperatures below 30°C yield correction factors greater than 1.00, but conductors must always be engineered to safely carry load under maximum expected summer peak temperatures.
Last updated: September 2026
9.2 Temperature Correction Factors
Exam Fast Fact: When performing conductor derating calculations on the Colorado Journeyman exam, always verify the ambient temperature units (Celsius vs. Fahrenheit) before selecting a correction factor from the bottom of NEC Table 310.16 . Derating factors must be selected based on the insulation temperature rating of the conductor (typically the 90°C column for THHN/THWN-2), not the equipment terminal rating. Terminal ratings apply only after all raceway derating calculations are complete.
Conductor ampacity is not an inherent, immutable constant. It represents the continuous current in amperes that a conductor can carry under conditions of use without exceeding its insulation temperature rating. The allowable ampacity values published in NEC Table 310.16 assume a standardized ambient temperature of 30°C (86°F) . When conductors are installed in environments hotter or colder than 30°C, electricians must apply mathematical correction factors to ensure the insulation is not compromised.
Conductor Thermal Physics & Ambient Equilibrium
Every ampere of current flowing through an electrical conductor encounters metallic resistance, generating heat according to Joule's Law of heating:
- P_loss = I² * R CONDUCTOR HEAT DISSIPATION DYNAMICS
- │
- ▼
- [HEAT GENERATED: I²R Losses]
- │
- ▼
- [CONDUCTOR INSULATION TEMPERATURE]
- │
- ┌─────────────────────────────┴─────────────────────────────┐
- ▼ ▼
- [DISSIPATED TO SURROUNDING AIR] [BLOCKED BY HIGH AMBIENT]
If ambient is 30°C or below: If ambient is 45°C (113°F):
- Rapid thermal transfer • Reduced thermal gradient
- Conductor operates at design ceiling • Conductor traps heat
• 100% of Table 310.16 ampacity safe • Ampacity must be derated!
A conductor reaches thermal equilibrium when the rate of internal I²R heat generation equals the rate at which heat is dissipated outward through the insulation into the surrounding atmosphere. The rate of heat dissipation depends directly on the temperature differential (Delta T) between the conductor core and the ambient air:
Standard Baseline (30°C / 86°F): At 30°C ambient, a 90°C-rated conductor has a thermal gradient of 90°C - 30°C = 60°C to shed heat. Under this condition, it can safely carry 100% of its Table 310.16 rated ampacity.
Elevated Ambient (e.g., 50°C / 122°F): If the ambient air is 50°C, the thermal gradient drops to 90°C - 50°C = 40°C. Because the conductor sheds heat far more slowly, continuing to carry rated current would push internal temperature past 90°C, causing the polymer insulation to soften, oxidize, embrittle, and experience premature dielectric breakdown.
The Arrhenius Law: In polymer chemistry, chemical aging doubles for roughly every 10°C rise above maximum rated temperature. Operating a 90°C conductor at 100°C cuts its anticipated service lifespan in half, transforming a 30-year commercial installation into an imminent electrical fire hazard.
The Ambient Temperature Correction Table
At the bottom of NEC Table 310.16 (and repeated in Table 310.15(B)(1) ), the NEC provides temperature correction factors categorized by ambient temperature ranges and conductor insulation temperature ratings: AMBIENT TEMPERATURE CORRECTION FACTORS TABLE
- (Based on 30°C / 86°F Baseline)
- ┌─────────────────────┬──────────────────┬───────┬───────┬───────┐
- │ Ambient Temp (°C) │ Ambient Temp (°F)│ 60°C │ 75°C │ 90°C │
- ├─────────────────────┼──────────────────┼───────┼───────┼───────┤
- │ 10°C or less │ 50°F or less │ 1.29 │ 1.20 │ 1.15 │
- │ 11°C – 15°C │ 51°F – 59°F │ 1.22 │ 1.15 │ 1.12 │
- │ 16°C – 20°C │ 60°F – 68°F │ 1.15 │ 1.11 │ 1.08 │
- │ 21°C – 25°C │ 69°F – 77°F │ 1.08 │ 1.05 │ 1.04 │
- │ 26°C – 30°C │ 78°F – 86°F │ 1.00 │ 1.00 │ 1.00 │
- │ 31°C – 35°C │ 87°F – 95°F │ 0.91 │ 0.94 │ 0.96 │
- │ 36°C – 40°C │ 96°F – 104°F │ 0.82 │ 0.88 │ 0.91 │
- │ 41°C – 45°C │ 105°F – 113°F │ 0.71 │ 0.82 │ 0.87 │
- │ 46°C – 50°C │ 114°F – 122°F │ 0.58 │ 0.75 │ 0.82 │
- │ 51°C – 55°C │ 123°F – 131°F │ 0.41 │ 0.67 │ 0.76 │
- │ 56°C – 60°C │ 132°F – 140°F │ — │ 0.58 │ 0.71 │
- │ 61°C – 65°C │ 141°F – 149°F │ — │ 0.47 │ 0.65 │
- │ 66°C – 70°C │ 150°F – 158°F │ — │ 0.33 │ 0.58 │
- │ 71°C – 75°C │ 159°F – 167°F │ — │ — │ 0.50 │
- │ 76°C – 80°C │ 168°F – 176°F │ — │ — │ 0.41 │
- └─────────────────────┴──────────────────┴───────┴───────┴───────┘
- Critical Observations from the Table
The 90°C Advantage: Notice how much more resilient 90°C-rated insulation is in elevated temperatures compared to 60°C and 75°C insulations. At 46°C–50°C (114°F–122°F), a 60°C conductor loses 42% of its capacity (factor 0.58), a 75°C conductor loses 25% (factor 0.75), while a 90°C conductor loses only 18% (factor 0.82).
High-Temperature Cutoffs: Notice the dashes (—) in the table. A 60°C conductor cannot be installed in environments above 55°C (131°F). A 75°C conductor cannot be installed in environments above 70°C (158°F). Above these temperatures, the ambient air alone exceeds the thermal tolerance of the insulation even with zero current flowing.
Step-by-Step Temperature Correction Calculation
Calculating corrected ampacity involves a simple, direct formula:
- Corrected Ampacity = Table 310.16 Ampacity × Temperature Correction Factor
- Calculation Example 1: Industrial Boiler Room
An electrician installs a feeder consisting of 3 AWG THHN Copper conductors in EMT through a commercial boiler room in Grand Junction, Colorado, where the ambient air temperature is measured at 43°C (109°F) . What is the allowable ampacity of the conductors in this room?
Step 1: Look up Base Ampacity in Table 310.16: For 3 AWG Copper under the 90°C column (THHN), the base ampacity is 115 amperes .
Step 2: Find the Correction Factor: Find 43°C in the ambient temperature table (range 41°C–45°C). Under the 90°C column, the factor is 0.87 .
Step 3: Calculate Corrected Ampacity: Corrected Ampacity = 115 A × 0.87 = 100.05 amperes
Step 4: Verify Terminal Coordination: Assuming the equipment terminals are rated at 75°C, check Table 310.16 for 3 AWG Cu in the 75°C column: 100 amperes . Because 100.05A is essentially equal to the 100A terminal rating, the conductor can safely carry up to 100A.
Calculation Example 2: Commercial Attic Feeder
A feeder with 1/0 AWG THHN Aluminum conductors runs through an unconditioned commercial roof space in Pueblo, Colorado, where summer peak attic temperatures reach 118°F .
Step 1: Look up Base Ampacity: For 1/0 AWG Aluminum in the 90°C column (THHN), base ampacity is 135 amperes .
Step 2: Find the Correction Factor: Find 118°F in the ambient temperature table (range 114°F–122°F / 46°C–50°C). Under the 90°C column, the factor is 0.82 .
Step 3: Calculate Corrected Ampacity: Corrected Ampacity = 135 A × 0.82 = 110.7 amperes
The conductor's safe carrying capacity in that attic is 110.7 amperes, down from 135 amperes.
Colorado Climate, High Elevation & Solar Radiation
Designing and installing electrical infrastructure in Colorado presents unique environmental challenges compared to sea-level jurisdictions: COLORADO HIGH-ALTITUDE FACTORS
- │
- ┌─────────────────────────────┼─────────────────────────────┐
- ▼ ▼ ▼
- ELEVATION SOLAR RADIATION TEMPERATURE SWINGS
- 5,280 ft (Denver) • Intense UV index • -15°F winter extremes
- 8,000–10,000+ ft towns • 20–25% less atmosphere • 100°F+ summer plains
- Lower air density • Extreme rooftop heating • High attic ambient
- Reduced air cooling • Black EPDM: 140°F+ • Wide expansion cycle
Reduced Air Density and Convective Cooling: At an elevation of 5,280 feet in Denver (and up to 9,000–10,000 feet in mountain mining towns and ski resorts like Breckenridge or Leadville), atmospheric pressure is significantly lower than at sea level. Thinner air reduces convective heat transfer away from conduit surfaces and electrical enclosures. Transformers, variable frequency drives, and heavily loaded raceways run hotter at high altitudes.
Intense Solar Thermal Gain: Colorado boasts over 300 days of sunshine annually. With thinner atmosphere filtering solar rays, solar irradiance is up to 25% more intense than at coastal latitudes. Commercial flat roofs with dark membrane surfaces absorb enormous radiant energy, pushing surface temperatures above 60°C (140°F) even on mild 85°F summer afternoons.
Extreme Seasonal Temperature Deltas: Colorado experiences ambient swings from -20°F (-29°C) during arctic winter fronts to 104°F (40°C) on the Eastern Plains. Raceways must be engineered with expansion fittings per NEC 300.7(B) , and conductors must be evaluated for summer peak ambient derating.
Rooftop Raceways Exposed to Direct Sunlight (NEC 310.15(B)(2))
One of the most heavily tested provisions on state licensing examinations is the treatment of raceways and cables installed on commercial rooftops exposed to direct solar heating. NEC 310.15(B)(2) ROOFTOP CLEARANCE RULE
- [ DIRECT SUNLIGHT / SOLAR RADIATION ]
- ↓↓↓↓↓↓
- CONDUIT A: LESS THAN 7/8 INCH ABOVE ROOF
- ──────────────────────────────────────────
- ══════════════════════════════════════════ [ROOF SURFACE]
- MANDATORY TEMPERATURE ADDER: +33°C (+60°F) to outdoor design temp!
- Causes severe conductor derating penalties!
- CONDUIT B: AT LEAST 7/8 INCH (22 MM) ABOVE ROOF
- ──────────────────────────────────────────
- ▲
- │ Clearance ≥ 7/8 in. (Mounted on Strut / Roof Blocks)
- ▼
- ══════════════════════════════════════════ [ROOF SURFACE]
- NO TEMPERATURE ADDER REQUIRED!
- Ambient temperature is strictly outdoor design temp.
The 7/8-Inch (22 mm) Clearance Rule
Under NEC 310.15(B)(2) :
Conduits Installed Less Than 7/8 in. (22 mm) Above Roof: For raceways or cables installed on or less than 7/8 in. above the rooftop where exposed to direct sunlight, a temperature adder of 33°C (60°F) shall be added to the outdoor design ambient temperature.
Conduits Installed At Least 7/8 in. (22 mm) Above Roof: Where raceways are mounted on approved rooftop support blocks or strut providing at least 7/8 inch of clear air space between the roof surface and the bottom of the raceway, no temperature adder is applied! Air circulation beneath the conduit dissipates the trapped roof heat, allowing the electrician to use the standard outdoor design temperature without an adder.
Comparison: The Financial and Sizing Impact of the 7/8-Inch Rule
Consider a commercial project in Denver where the outdoor summer design ambient temperature is 36°C (97°F) . We are installing 2/0 AWG THHN Copper conductors (90°C base ampacity = 195A):
Case A: Conduit laid flat on roof surface (< 7/8 in.): Effective Ambient Temp = 36°C + 33°C (adder) = 69°C (157°F)
Looking at the correction table under the 90°C column for 66°C–70°C (150°F–158°F), the factor is 0.58 .
Corrected Ampacity = 195 A × 0.58 = 113.1 amperes Result: The conductor loses 82 amperes of capacity (over 42% loss)!
Case B: Conduit mounted on 1.5-inch rooftop support blocks (>= 7/8 in.): Effective Ambient Temp = 36°C (No Adder!)
Looking at the correction table under the 90°C column for 36°C–40°C (96°F–104°F), the factor is 0.91 .
Corrected Ampacity = 195 A × 0.91 = 177.45 amperes Result: By spending $15 on rooftop support blocks to raise the conduit 7/8 inch off the roof, the allowable ampacity jumps from 113.1A to 177.45A—a massive 64.35-ampere gain that avoids upsizing conductors and raceways!
Sub-30°C Ambient Environments: Cold-Climate Factors
At the top of the temperature correction table, ambient temperature ranges below 30°C (86°F) feature correction factors greater than 1.00 :
21°C–25°C (69°F–77°F): Factor is 1.04 (for 90°C wire).
16°C–20°C (60°F–68°F): Factor is 1.08 (for 90°C wire).
11°C–15°C (51°F–59°F): Factor is 1.12 (for 90°C wire).
10°C or less (50°F or less): Factor is 1.15 (for 90°C wire).
Can You Downsize Wire in Cold Climates?
In winter, mountain towns in Colorado routinely operate in ambient temperatures well below 0°C. While cooler air accelerates heat dissipation, allowing a conductor to theoretically carry more current without exceeding insulation limits, NEC 310.14(A)(1) and engineering practice require electrical systems to be designed for the worst-case maximum peak ambient temperature likely to occur during operation.
Downsizing a feeder conductor based on cold winter temperatures means the conductor will catastrophically overheat as soon as summer arrives. Cold-temperature correction factors are applied primarily in specialized climate-controlled industrial refrigeration facilities, frozen-food processing warehouses, or cryogenics plants where the ambient temperature is permanently and mechanically held below 10°C year-round.
Jobsite Scenarios & Common Exam Traps
Jobsite Scenario Technical Reality & Code Mandate Common PSI Exam Trap
Rooftop Solar Feeder: Conduit with THWN-2 conductors runs across a flat roof secured directly to the gravel surface. Violation of NEC 310.15(B)(2): Conduits less than 7/8 in. off the roof require a 33°C (60°F) temperature adder added to outdoor design temperature, severely penalizing ampacity. Mounting on 7/8 in. blocks eliminates the adder. Assuming rooftop conductors only derate if installed in uninsulated attics.
Boiler Room Unit Heater: An electrician runs a branch circuit using 12 AWG THHN copper in a 42°C industrial boiler room to supply a continuous 16A load. Under-Sized Conductor: 12 AWG THHN base is 30A. Temp factor for 41–45°C is 0.87 (30 A × 0.87 = 26.1 A). Continuous load requires 16 A × 1.25 = 20 A. While 26.1A > 20A, terminal rating at 75°C is 25A (25 A × 0.87 = 21.75 A). Works, but leaves zero margin. Forgetting to verify both terminal compatibility and derated raceway ampacity.
Wrong Column Derating: An apprentice uses the 75°C column to look up the temperature correction factor for THHN wire because the breaker has 75°C terminals. Calculation Error: Conductor derating for ambient heat is based strictly on the insulation rating of the wire (90°C column for THHN). Terminal ratings are checked at the end of the calculation, not during derating factor selection. Selecting correction factors from the 75°C column for 90°C insulated conductors.
Freezer Warehouse Circuit: An installer sizes conductors for a walk-in freezer at -10°C using a 1.20 correction factor, reducing wire from 10 AWG to 12 AWG. Code Violation (Worst-Case Design): The circuit passes through a 25°C loading dock before entering the freezer. Conductors must be sized for the highest ambient temperature through which the raceway passes per NEC 310.14(A)(2). Applying cold-temperature bonus factors to circuits that pass through normal-temperature spaces.