Study guide
2.3 Three-Phase Electrical Systems: Wye & Delta Configurations
Colorado Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Colorado Electrical Licensing Laws, DORA Rules & Exam Logistics
1.1 Colorado Electrical Board, Licensure Tiers & Application Process 1.2 Senate Bill 25-165, Apprentice Supervision & Colorado Board Rules 1.3 Permitting, Inspection Procedures, Violations & Penalties 1.4 The Colorado PSI Exam: Open-Book Format, Time Management & Code Navigation
2 Chapter 2: Electrical Theory, Mathematics & Fundamental Concepts
2.1 Ohm's Law, Joule's Law & DC Circuit Analysis 2.2 AC Fundamentals: Inductance, Capacitance & Power Factor 2.3 Three-Phase Electrical Systems: Wye & Delta Configurations 2.4 Voltage Drop Principles & Single/Three-Phase Formulas
3 Chapter 3: General Installation Requirements — NEC Articles 90 & 110
3.1 NEC Structure, Arrangement & Article 90 Fundamentals 3.2 Key Article 100 Definitions for the Exam 3.3 Equipment Examination, Listing & Termination Temperature Limits 3.4 Working Space, Dedicated Electrical Space & Guarding
4 Chapter 4: Branch Circuits & Feeders — NEC Articles 210, 215 & 225
4.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Branch Circuits 4.2 Dwelling Unit Required Outlets & Receptacle Placement 4.3 Ground-Fault Circuit-Interrupter (GFCI) Protection 4.4 Arc-Fault Circuit-Interrupter (AFCI) Protection & Feeder Rules
5 Chapter 5: Services & Overcurrent Protection — NEC Articles 230, 240 & 242
5.1 Service Conductors, Clearances & Overhead/Underground Drops 5.2 Service Disconnecting Means, Ratings & Surge Protection 5.3 Overcurrent Protection Fundamentals & Standard Ratings 5.4 Feeder & Transformer Tap Rules
6 Chapter 6: Grounding and Bonding — NEC Article 250 Part I (Systems & Electrodes)
6.1 Grounding vs. Bonding: Principles, Functions & Article 250 Architecture 6.2 Grounded Conductors, Main Bonding Jumpers & System Bonding Jumpers 6.3 The Grounding Electrode System 6.4 Grounding Electrode Conductor (GEC) Sizing & Installation
7 Chapter 7: Grounding and Bonding — NEC Article 250 Part II (Equipment & Special Systems)
7.1 Equipment Grounding Conductors (EGC) Types & Identification 7.2 Sizing the Equipment Grounding Conductor 7.3 Separately Derived Systems 7.4 Grounding & Bonding at Separate Buildings or Structures
8 Chapter 8: Wiring Methods & Materials — NEC Chapter 3
8.1 General Wiring Requirements & Underground Installations 8.2 Nonmetallic and Armored Cable Assemblies 8.3 Metallic and Nonmetallic Raceways 8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways
9 Chapter 9: Conductors, Ampacity & Wire Sizing — NEC Article 310
9.1 Conductor Properties, Insulation Types & NEC Table 310.16 9.2 Temperature Correction Factors 9.3 Conductor Bundling & Adjustment Factors 9.4 Comprehensive Conductor Sizing & Terminal Temperature Coordination
10 Chapter 10: Box Fill, Conduit Fill & Pull Box Calculations
10.1 Outlet and Device Box Fill Calculations — NEC 314.16(A) & (B) 10.2 Conduit Fill Calculations — Chapter 9 Tables 1, 4, 5 & Annex C 10.3 Pull and Junction Box Sizing for Conductors 4 AWG and Larger — NEC 314.28 10.4 Practical Enclosure & Raceway Sizing Exam Scenarios
11 Chapter 11: Load Calculations — Dwellings & Commercial Buildings — NEC Article 120
11.1 General Lighting, Small Appliance & Laundry Loads 11.2 Fixed Appliances, Dryers & Cooking Equipment Calculations 11.3 Standard vs. Optional Calculation Methods for Single-Family Dwellings 11.4 Commercial & Multifamily Load Calculations
12 Chapter 12: Motors, Motor Circuits & Controllers — NEC Article 430
12.1 Motor Nameplate vs. NEC Tables & Motor Full-Load Current 12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection 12.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 12.4 Motor Feeders, Disconnecting Means & Controllers
13 Chapter 13: Transformers, Distribution & Utilization Equipment
13.1 Transformer Overcurrent Protection & Installation — NEC Article 450 13.2 Panelboards, Switchboards & Switchgear — NEC Article 408 13.3 Luminaires, Appliances & Fixed Electric Space Heating 13.4 Generators, Transfer Switches & Standby Systems
14 Chapter 14: Special Occupancies, Renewable Energy & Modern Technologies
14.1 Hazardous (Classified) Locations — NEC Articles 500-516 14.2 Health Care Facilities & Places of Assembly — NEC Articles 517 & 518 14.3 Swimming Pools, Spas, Hot Tubs & Fountains — NEC Article 680 14.4 Solar Photovoltaic (PV) Systems & Energy Storage — NEC Articles 690, 705 & 706
2.3 Three-Phase Electrical Systems: Wye & Delta Configurations
Key Takeaways Explain This Topic AI
Three-phase AC electrical generation utilizes three separate stator windings displaced by 120 electrical degrees, delivering continuous constant instantaneous power and superior motor starting torque compared to single-phase systems.
In a 4-wire Wye (Star) distribution system, line-to-line voltage is √3 (1.732) times line-to-neutral phase voltage (Vline = Vphase × 1.732), while line current equals transformer phase winding current (Iline = Iphase).
In a Delta (Mesh) configuration, line-to-line voltage equals transformer phase winding voltage (Vline = Vphase), while line current is √3 (1.732) times phase current (Iline = Iphase × 1.732).
In a 120/240V 4-wire high-leg delta system, the center-tapped winding provides 120V to neutral on phases A and C, while Phase B (the high leg) produces 208V to neutral and must be permanently identified with orange marking per NEC 110.15 and connected to the B phase bus per NEC 408.3(E)(1).
Total three-phase apparent and real power calculations universally require the square root of three factor (√3 ≈ 1.732): S = √3 × Vline × Iline and P = √3 × Vline × Iline × PF, regardless of whether the system is connected in Wye or Delta.
Last updated: September 2026
2.3 Three-Phase Electrical Systems: Wye & Delta Configurations
Quick Answer: Three-phase AC electrical systems generate three sinusoidal voltages separated by 120 ∘ 120^\circ 12 0 ∘ of electrical rotation. In a Wye (Y) system, line-to-line voltage is 3 \sqrt{3} 3 ( 1.732 1.732 1.732 ) times line-to-neutral phase voltage ( V line = V phase × 1.732 V_{\text{line}} = V_{\text{phase}} \times 1.732 V line = V phase × 1.732 ), while line current equals phase current ( I line = I phase I_{\text{line}} = I_{\text{phase}} I line = I phase ). In a Delta ( Δ \Delta Δ ) system, line voltage equals phase voltage ( V line = V phase V_{\text{line}} = V_{\text{phase}} V line = V phase ), while line current is 3 \sqrt{3} 3 times phase winding current ( I line = I phase × 1.732 I_{\text{line}} = I_{\text{phase}} \times 1.732 I line = I phase × 1.732 ). The 120 / 240 V 120/240\text{ V} 120/240 V 4-wire high-leg delta system produces 208 V 208\text{ V} 208 V between the center-tapped neutral and Phase B; NEC 110.15 mandates this high leg be marked with orange identification, and NEC 408.3(E)(1) requires termination on the center (B-phase) bus. Total three-phase power is calculated using P = 3 × V line × I line × PF P = \sqrt{3} \times V_{\text{line}} \times I_{\text{line}} \times \text{PF} P = 3 × V line × I line × PF .
Three-phase electrical distribution is the global standard for industrial manufacturing, commercial facilities, and utility power generation. Compared to single-phase systems delivering equivalent power, three-phase systems require significantly less conductor material (roughly 75 % 75\% 75% of the copper), maintain a continuous, non-pulsating instantaneous power transfer, and produce rotating magnetic fields inside AC motors that eliminate the need for starting capacitors, centrifugal switches, or auxiliary split-phase windings.
Three-Phase Power Generation & The 120-Degree Phase Displacement
Inside a commercial three-phase utility alternator, three separate armature windings are physically mounted on the stator, positioned precisely 120 ∘ 120^\circ 12 0 ∘ apart . As the rotor's magnetic field spins:
Phase A reaches its positive maximum peak voltage.
One-third of a cycle later ( 120 ∘ 120^\circ 12 0 ∘ ), Phase B reaches its positive peak.
Another one-third of a cycle later ( 240 ∘ 240^\circ 24 0 ∘ ), Phase C reaches its positive peak. v A ( t ) = V pk sin ( ω t ) v_A(t) = V_{\text{pk}} \sin(\omega t) v A ( t ) = V pk sin ( ω t ) v B ( t ) = V pk sin ( ω t − 120 ∘ ) v_B(t) = V_{\text{pk}} \sin(\omega t - 120^\circ) v B ( t ) = V pk sin ( ω t − 12 0 ∘ ) v C ( t ) = V pk sin ( ω t − 240 ∘ ) = V pk sin ( ω t + 120 ∘ ) v_C(t) = V_{\text{pk}} \sin(\omega t - 240^\circ) = V_{\text{pk}} \sin(\omega t + 120^\circ) v C ( t ) = V pk sin ( ω t − 24 0 ∘ ) = V pk sin ( ω t + 12 0 ∘ )
The Balanced Neutral Cancellation Principle
In any balanced three-phase system carrying identical linear load currents on all three ungrounded conductors, the algebraic sum of the instantaneous currents equals zero at every point in time: ∋ A ( t ) + i B ( t ) + i C ( t ) = 0 \ni_A(t) + i_B(t) + i_C(t) = 0 ∋ A ( t ) + i B ( t ) + i C ( t ) = 0
Because the currents cancel out, a balanced three-phase 4-wire Wye system carries 0 amperes 0\text{ amperes} 0 amperes on the common neutral conductor . If loads become unbalanced, the neutral carries only the resultant vector imbalance.
Wye (Star) Connected Systems: Voltage & Current Rules
In a Wye (symbolized as Y) configuration, one end of each of the three transformer coils is connected together at a single common junction called the neutral point or star point . The three remaining coil ends are brought out as the phase conductors (Phase A, Phase B, and Phase C). When a grounded neutral conductor is run from the star point, the system becomes a 3-phase, 4-wire Wye system.
Mathematical Rules for Wye Systems
Line Voltage vs. Phase Voltage: The voltage measured between any two ungrounded line conductors ( V line-to-line V_{\text{line-to-line}} V line-to-line or V L V_L V L ) is the vector difference between two coils separated by 120 ∘ 120^\circ 12 0 ∘ . This yields the square root of three factor ( 3 ≈ 1.73205 \sqrt{3} \approx 1.73205 3 ≈ 1.73205 ): V line = V phase × 3 = V phase × 1.732 V_{\text{line}} = V_{\text{phase}} \times \sqrt{3} = V_{\text{phase}} \times 1.732 V line = V phase × 3 = V phase × 1.732 V phase = V line 3 = V line 1.732 V_{\text{phase}} = \frac{V_{\text{line}}}{\sqrt{3}} = \frac{V_{\text{line}}}{1.732} V phase = 3 V line = 1.732 V line
Line Current vs. Phase Current: Because every external line conductor connects in direct series with an internal transformer winding coil, line current is identical to transformer phase current: I line = I phase I_{\text{line}} = I_{\text{phase}} I line = I phase
Standard Commercial & Industrial Wye System Configurations
Nominal Voltage Line-to-Line ( V L V_L V L ) Line-to-Neutral ( V N V_N V N ) Primary Applications
208 Y / 120 V 208\text{Y}/120\text{ V} 208 Y /120 V 208 V 208\text{ V} 208 V 120 V 120\text{ V} 120 V Commercial office buildings, schools, retail stores, multifamily housing. Provides 120 V 120\text{ V} 120 V convenience receptacles and lighting, plus 208 V 208\text{ V} 208 V single-phase and three-phase motor loads.
480 Y / 277 V 480\text{Y}/277\text{ V} 480 Y /277 V 480 V 480\text{ V} 480 V 277 V 277\text{ V} 277 V Heavy industrial plants, institutional facilities, large commercial warehouses. Provides 277 V 277\text{ V} 277 V lighting (higher voltage reduces wire size) and 480 V 480\text{ V} 480 V for large chillers, air compressors, and motor control centers (MCCs).
Neutral Conductor Dynamics & Harmonic Loading in Wye Systems
On a balanced linear resistive or inductive load (e.g., three identical heating elements or a three-phase motor), neutral current is zero. However, modern commercial facilities are dominated by non-linear switch-mode power supplies (computers, servers, variable frequency drives, electronic LED drivers). Non-linear loads draw current in short, abrupt pulses rather than smooth sine waves, generating heavy triplen harmonics (specifically the 3rd harmonic at 180 Hz 180\text{ Hz} 180 Hz , 9th at 540 Hz 540\text{ Hz} 540 Hz , and 15th at 900 Hz 900\text{ Hz} 900 Hz ).
Unlike fundamental 60 Hz 60\text{ Hz} 60 Hz currents which cancel in the neutral, triplen harmonics are in phase with each other and add up arithmetically in the neutral conductor. In high-density server rooms, neutral current can reach 140 % 140\% 140% to 170 % 170\% 170% of phase current, creating severe overheating if the neutral conductor is not properly sized or doubled.
Delta (Mesh) Connected Systems: Voltage & Current Rules
In a Delta (symbolized as Δ \Delta Δ ) configuration, the three transformer phase windings are connected end-to-end in a closed triangular series loop: the finish of Phase A connects to the start of Phase B, the finish of Phase B connects to the start of Phase C, and the finish of Phase C connects back to the start of Phase A. External line conductors are tapped directly from the three triangle vertices.
Mathematical Rules for Delta Systems
Line Voltage vs. Phase Voltage: Because each external pair of line conductors is connected directly across an individual transformer phase winding, line voltage equals phase voltage: V line = V phase V_{\text{line}} = V_{\text{phase}} V line = V phase
Line Current vs. Phase Current: Each external line conductor connects to the junction of two different transformer phase windings. Applying Kirchhoff's Current Law vectorially, external line current is 3 \sqrt{3} 3 ( 1.732 1.732 1.732 ) times the internal winding phase current: I line = I phase × 3 = I phase × 1.732 I_{\text{line}} = I_{\text{phase}} \times \sqrt{3} = I_{\text{phase}} \times 1.732 I line = I phase × 3 = I phase × 1.732 I phase = I line 3 = I line 1.732 I_{\text{phase}} = \frac{I_{\text{line}}}{\sqrt{3}} = \frac{I_{\text{line}}}{1.732} I phase = 3 I line = 1.732 I line
Standard Industrial Delta Configurations
240 V 240\text{ V} 240 V , 3-Phase, 3-Wire Delta: Common in legacy industrial machine shops. Delivers pure 240 V 240\text{ V} 240 V line-to-line for motors. Can be ungrounded or corner-grounded (one phase conductor grounded to establish reference to earth).
480 V 480\text{ V} 480 V , 3-Phase, 3-Wire Delta: Utilized in heavy industrial processing, manufacturing plants, and mining operations where no line-to-neutral lighting loads are served.
The 120/240V 4-Wire High-Leg (Wild-Leg) Delta System
The 120 / 240 V 120/240\text{ V} 120/240 V 4-wire high-leg delta system (also known as a "wild-leg," "stinger leg," or "red leg" system) was engineered to provide both three-phase power for heavy equipment and standard single-phase 120 V 120\text{ V} 120 V power for lighting and receptacles from a single transformer bank.
How It Is Configured
A standard three-phase delta transformer secondary has one of its 240 V 240\text{ V} 240 V windings center-tapped to establish a system grounded neutral conductor: Phase B (High Leg - 208V to Neutral)
- /\
- / \
- / \
- / \
- 240V / \ 240V
- / \
- / \
- / \
- / N \
- Phase A ------------+--------+---------+------------ Phase C
- 120V 120V
- <---- 240V ---->
- Voltage Measurements in a 120/240V High-Leg Delta System
- Measurement Test Points Measured Voltage Circuit Purpose
- Phase A to Phase B 240 V 240\text{ V} 240 V Three-phase equipment, motors, welders
- Phase B to Phase C 240 V 240\text{ V} 240 V Three-phase equipment, motors, welders
- Phase A to Phase C 240 V 240\text{ V} 240 V Three-phase equipment, 240 V 240\text{ V} 240 V single-phase loads
Phase A to Neutral 120 V 120\text{ V} 120 V Standard 120 V 120\text{ V} 120 V convenience receptacles and lighting
Phase C to Neutral 120 V 120\text{ V} 120 V Standard 120 V 120\text{ V} 120 V convenience receptacles and lighting
Phase B to Neutral (High Leg) 208 V 208\text{ V} 208 V DO NOT USE FOR 120V LOADS! ( 240 V × 0.866 = 208 V 240\text{ V} \times 0.866 = 208\text{ V} 240 V × 0.866 = 208 V )
Vector Geometry: Why the High Leg Measures 208V to Neutral
The high leg voltage is calculated by bisecting the equilateral 240 V 240\text{ V} 240 V delta triangle. The neutral sits at the center of the Phase A–Phase C base. The perpendicular height from this center tap to the opposite vertex (Phase B) is: V High-Leg = V line × 3 2 = 240 V × 0.8660 = 207.84 V ≈ 208 V V_{\text{High-Leg}} = V_{\text{line}} \times \frac{\sqrt{3}}{2} = 240\text{ V} \times 0.8660 = 207.84\text{ V} \approx 208\text{ V} V High-Leg = V line × 2 3 = 240 V × 0.8660 = 207.84 V ≈ 208 V
Mandatory NEC Requirements for High-Leg Systems
Conductor Identification (NEC 110.15 & 230.56): On a 4-wire, delta-connected system where the midpoint of one phase winding is grounded, the conductor or busbar having the higher phase voltage to ground (Phase B) shall be durably and permanently identified by an outer finish that is orange in color , by tagging, or by other effective means at every point where a connection is made if the grounded conductor is also present.
Busbar Position in Switchboards and Panelboards (NEC 408.3(E)(1)): In switchboards, switchgear, and panelboards, the high-leg conductor shall connect to the "B" phase bus (the center bus bar), unless the equipment contains metering equipment where utility company standards dictate connection to Phase C.
Catastrophic Field Hazards: 120V Loads on the 208V High Leg
Connecting a standard 120 V 120\text{ V} 120 V single-phase load (such as desktop computers, LED lighting ballasts, or convenience receptacles) between the high leg and the neutral conductor applies 208 V 208\text{ V} 208 V across equipment rated for 120 V 120\text{ V} 120 V . This error results in immediate destruction of internal electronics, blown power supplies, and extreme arc-flash/fire hazard. Single-pole breakers must never be installed on Phase B bus stabs in high-leg panels unless explicitly serving a specialized 208V single-phase rated load.
Three-Phase Power Formulas & Calculations
Regardless of whether a system is internally configured as Wye or Delta, total apparent power ( S S S ), real power ( P P P ), and reactive power ( Q Q Q ) are calculated using the universal line-to-line parameters: S = 3 × V line × I line = 1.732 × V L × I L (in VA or kVA) S = \sqrt{3} \times V_{\text{line}} \times I_{\text{line}} = 1.732 \times V_L \times I_L \quad \text{(in VA or kVA)} S = 3 × V line × I line = 1.732 × V L × I L (in VA or kVA) P = 3 × V line × I line × PF = 1.732 × V L × I L × PF (in W or kW) P = \sqrt{3} \times V_{\text{line}} \times I_{\text{line}} \times \text{PF} = 1.732 \times V_L \times I_L \times \text{PF} \quad \text{(in W or kW)} P = 3 × V line × I line × PF = 1.732 × V L × I L × PF (in W or kW) Q = 3 × V line × I line × sin θ (in VAR or kVAR) Q = \sqrt{3} \times V_{\text{line}} \times I_{\text{line}} \times \sin\theta \quad \text{(in VAR or kVAR)} Q = 3 × V line × I line × sin θ (in VAR or kVAR)
To solve for line current ( I line I_{\text{line}} I line ): I line = P 3 × V line × PF = P 1.732 × V L × PF I_{\text{line}} = \frac{P}{\sqrt{3} \times V_{\text{line}} \times \text{PF}} = \frac{P}{1.732 \times V_L \times \text{PF}} I line = 3 × V line × PF P = 1.732 × V L × PF P I line = S 3 × V line = S 1.732 × V L I_{\text{line}} = \frac{S}{\sqrt{3} \times V_{\text{line}}} = \frac{S}{1.732 \times V_L} I line = 3 × V line S = 1.732 × V L S
Worked Example 1: Calculating Current and Power for a 480V Three-Phase Motor
Problem: A 480 V 480\text{ V} 480 V , three-phase induction motor has a nameplate full-load current of 50 A 50\text{ A} 50 A operating at an 85 % 85\% 85% power factor ( 0.85 0.85 0.85 ). Calculate the apparent power in kVA and true real power in kW.
Step 1: Calculate Apparent Power ( S S S ): S = 3 × V L × I L = 1.732 × 480 V × 50 A = 41,568 VA = 41.57 kVA S = \sqrt{3} \times V_L \times I_L = 1.732 \times 480\text{ V} \times 50\text{ A} = 41{,}568\text{ VA} = 41.57\text{ kVA} S = 3 × V L × I L = 1.732 × 480 V × 50 A = 41 , 568 VA = 41.57 kVA
Step 2: Calculate Real Power ( P P P ): P = S × PF = 41.57 kVA × 0.85 = 35.33 kW P = S \times \text{PF} = 41.57\text{ kVA} \times 0.85 = 35.33\text{ kW} P = S × PF = 41.57 kVA × 0.85 = 35.33 kW (Or: P = 1.732 × 480 × 50 × 0.85 = 35,333 W = 35.33 kW P = 1.732 \times 480 \times 50 \times 0.85 = 35{,}333\text{ W} = 35.33\text{ kW} P = 1.732 × 480 × 50 × 0.85 = 35 , 333 W = 35.33 kW )
Worked Example 2: Sizing Line Conductors for a 208V Commercial Kitchen Load
Problem: A balanced three-phase commercial electric pizza oven consumes 25 kW 25\text{ kW} 25 kW of pure resistive heating at 208 V 208\text{ V} 208 V (unity power factor, PF = 1.0 \text{PF} = 1.0 PF = 1.0 ). Calculate the full-load line current.
Calculation: I line = P 3 × V L × PF = 25,000 W 1.732 × 208 V × 1.0 = 25,000 360.256 = 69.39 A I_{\text{line}} = \frac{P}{\sqrt{3} \times V_L \times \text{PF}} = \frac{25{,}000\text{ W}}{1.732 \times 208\text{ V} \times 1.0} = \frac{25{,}000}{360.256} = 69.39\text{ A} I line = 3 × V L × PF P = 1.732 × 208 V × 1.0 25 , 000 W = 360.256 25 , 000 = 69.39 A
Comparing Wye and Delta Systems: Field Application Matrix
- Feature / Parameter Wye (Star) System Delta (Mesh) System
- Common Center Tap Yes, neutral star point available No common star point natively
Line vs Phase Voltage V line = V phase × 1.732 V_{\text{line}} = V_{\text{phase}} \times 1.732 V line = V phase × 1.732 V line = V phase V_{\text{line}} = V_{\text{phase}} V line = V phase
Line vs Phase Current I line = I phase I_{\text{line}} = I_{\text{phase}} I line = I phase I line = I phase × 1.732 I_{\text{line}} = I_{\text{phase}} \times 1.732 I line = I phase × 1.732
Neutral Conductor 4th wire grounded neutral provides single-phase voltage Only available if one winding is center-tapped (high-leg)
Voltages Delivered Dual voltage: 208 Y / 120 V 208\text{Y}/120\text{ V} 208 Y /120 V or 480 Y / 277 V 480\text{Y}/277\text{ V} 480 Y /277 V Single voltage ( 240 V 240\text{ V} 240 V or 480 V 480\text{ V} 480 V ), or high-leg ( 120 / 240 V 120/240\text{ V} 120/240 V )
Ground-Fault Characteristic Solidly grounded neutral establishes stable reference Ungrounded delta can sustain single phase-to-ground fault without tripping
Phase Winding Insulation Windings insulated for lower phase voltage ( V L / 1.732 V_L / 1.732 V L /1.732 ) Windings must be insulated for full line-to-line voltage
Colorado Journeyman Exam Traps & Pitfalls
Trap 1: Using Phase Voltage in the Three-Phase Power Formula: When calculating three-phase power, always use line-to-line voltage ( 208 V 208\text{ V} 208 V or 480 V 480\text{ V} 480 V ) when multiplying by 3 \sqrt{3} 3 . If you use phase voltage ( 120 V 120\text{ V} 120 V or 277 V 277\text{ V} 277 V ), you must multiply by 3 3 3 instead of 3 \sqrt{3} 3 ( P = 3 × V phase × I phase × PF P = 3 \times V_{\text{phase}} \times I_{\text{phase}} \times \text{PF} P = 3 × V phase × I phase × PF ). Mixing 3 \sqrt{3} 3 with phase voltage cuts your answer by 42 % 42\% 42% .
Trap 2: Assuming the High Leg is 240V to Ground: The voltage from the high leg to neutral is 208 V 208\text{ V} 208 V , not 240 V 240\text{ V} 240 V ! The voltage is 240 V 240\text{ V} 240 V only when measured phase-to-phase.
Trap 3: High-Leg Bus Positioning: Under NEC 408.3(E)(1), the high-leg conductor must always connect to the B phase (center) busbar in panelboards, not Phase A or Phase C, unless the panel contains metering equipment where the utility specifically requires Phase C.