Study guide
3.3 Equipment Examination, Listing & Termination Temperature Limits
Colorado Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Colorado Electrical Licensing Laws, DORA Rules & Exam Logistics
1.1 Colorado Electrical Board, Licensure Tiers & Application Process 1.2 Senate Bill 25-165, Apprentice Supervision & Colorado Board Rules 1.3 Permitting, Inspection Procedures, Violations & Penalties 1.4 The Colorado PSI Exam: Open-Book Format, Time Management & Code Navigation
2 Chapter 2: Electrical Theory, Mathematics & Fundamental Concepts
2.1 Ohm's Law, Joule's Law & DC Circuit Analysis 2.2 AC Fundamentals: Inductance, Capacitance & Power Factor 2.3 Three-Phase Electrical Systems: Wye & Delta Configurations 2.4 Voltage Drop Principles & Single/Three-Phase Formulas
3 Chapter 3: General Installation Requirements — NEC Articles 90 & 110
3.1 NEC Structure, Arrangement & Article 90 Fundamentals 3.2 Key Article 100 Definitions for the Exam 3.3 Equipment Examination, Listing & Termination Temperature Limits 3.4 Working Space, Dedicated Electrical Space & Guarding
4 Chapter 4: Branch Circuits & Feeders — NEC Articles 210, 215 & 225
4.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Branch Circuits 4.2 Dwelling Unit Required Outlets & Receptacle Placement 4.3 Ground-Fault Circuit-Interrupter (GFCI) Protection 4.4 Arc-Fault Circuit-Interrupter (AFCI) Protection & Feeder Rules
5 Chapter 5: Services & Overcurrent Protection — NEC Articles 230, 240 & 242
5.1 Service Conductors, Clearances & Overhead/Underground Drops 5.2 Service Disconnecting Means, Ratings & Surge Protection 5.3 Overcurrent Protection Fundamentals & Standard Ratings 5.4 Feeder & Transformer Tap Rules
6 Chapter 6: Grounding and Bonding — NEC Article 250 Part I (Systems & Electrodes)
6.1 Grounding vs. Bonding: Principles, Functions & Article 250 Architecture 6.2 Grounded Conductors, Main Bonding Jumpers & System Bonding Jumpers 6.3 The Grounding Electrode System 6.4 Grounding Electrode Conductor (GEC) Sizing & Installation
7 Chapter 7: Grounding and Bonding — NEC Article 250 Part II (Equipment & Special Systems)
7.1 Equipment Grounding Conductors (EGC) Types & Identification 7.2 Sizing the Equipment Grounding Conductor 7.3 Separately Derived Systems 7.4 Grounding & Bonding at Separate Buildings or Structures
8 Chapter 8: Wiring Methods & Materials — NEC Chapter 3
8.1 General Wiring Requirements & Underground Installations 8.2 Nonmetallic and Armored Cable Assemblies 8.3 Metallic and Nonmetallic Raceways 8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways
9 Chapter 9: Conductors, Ampacity & Wire Sizing — NEC Article 310
9.1 Conductor Properties, Insulation Types & NEC Table 310.16 9.2 Temperature Correction Factors 9.3 Conductor Bundling & Adjustment Factors 9.4 Comprehensive Conductor Sizing & Terminal Temperature Coordination
10 Chapter 10: Box Fill, Conduit Fill & Pull Box Calculations
10.1 Outlet and Device Box Fill Calculations — NEC 314.16(A) & (B) 10.2 Conduit Fill Calculations — Chapter 9 Tables 1, 4, 5 & Annex C 10.3 Pull and Junction Box Sizing for Conductors 4 AWG and Larger — NEC 314.28 10.4 Practical Enclosure & Raceway Sizing Exam Scenarios
11 Chapter 11: Load Calculations — Dwellings & Commercial Buildings — NEC Article 120
11.1 General Lighting, Small Appliance & Laundry Loads 11.2 Fixed Appliances, Dryers & Cooking Equipment Calculations 11.3 Standard vs. Optional Calculation Methods for Single-Family Dwellings 11.4 Commercial & Multifamily Load Calculations
12 Chapter 12: Motors, Motor Circuits & Controllers — NEC Article 430
12.1 Motor Nameplate vs. NEC Tables & Motor Full-Load Current 12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection 12.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 12.4 Motor Feeders, Disconnecting Means & Controllers
13 Chapter 13: Transformers, Distribution & Utilization Equipment
13.1 Transformer Overcurrent Protection & Installation — NEC Article 450 13.2 Panelboards, Switchboards & Switchgear — NEC Article 408 13.3 Luminaires, Appliances & Fixed Electric Space Heating 13.4 Generators, Transfer Switches & Standby Systems
14 Chapter 14: Special Occupancies, Renewable Energy & Modern Technologies
14.1 Hazardous (Classified) Locations — NEC Articles 500-516 14.2 Health Care Facilities & Places of Assembly — NEC Articles 517 & 518 14.3 Swimming Pools, Spas, Hot Tubs & Fountains — NEC Article 680 14.4 Solar Photovoltaic (PV) Systems & Energy Storage — NEC Articles 690, 705 & 706
3.3 Equipment Examination, Listing & Termination Temperature Limits
Key Takeaways Explain This Topic AI
Under NEC 110.3(B), listed and labeled equipment must be installed and used strictly in accordance with manufacturer instructions and listing conditions; failure to follow listing instructions constitutes an explicit Code violation.
NEC 110.12 mandates neat and workmanlike execution, requiring unused enclosure knockouts to be closed with approved plugs or fittings affording protection substantially equivalent to the wall.
Circuits rated 100A or less, or marked for conductors #14 through #1 AWG, default to the 60°C terminal column of Table 310.16 unless equipment and devices are explicitly listed and marked for 75°C.
Circuits over 100A, or conductors larger than #1 AWG, default to 75°C terminal ratings under NEC 110.14(C)(1)(b).
Conductors with 90°C insulation (e.g., THHN) can use 90°C ampacity for ambient temperature correction and conductor bundling adjustment, but the final corrected ampacity can never exceed the terminal rating (typically 75°C).
Last updated: September 2026
3.3 Equipment Examination, Listing & Termination Temperature Limits
Article 110 sets out the general requirements for electrical installations. It establishes how equipment must be evaluated, approved, mounted, spliced, and terminated. On the Colorado Journeyman exam, questions from Article 110 separate candidates who simply guess from those who grasp the core engineering principles of electrical construction. In particular, conductor termination temperature coordination under NEC 110.14(C) is one of the most heavily tested calculation concepts in the Code.
Equipment Examination, Installation & Use (NEC 110.3)
Before electrical equipment is energized, it must be evaluated for safety and suitability. Under NEC 110.3(A) , the AHJ evaluates equipment based on eight safety factors:
Suitability: Suitability for installation and use in conformity with the provisions of the Code (investigated through listing or labeling).
Mechanical Strength: Mechanical strength and durability, including the adequacy of the protection provided for enclosures.
Wire-Bending & Connection Space: Adequacy of internal wire-bending space and termination areas.
Electrical Insulation: Quality and integrity of electrical insulation.
Heating Effects: Heating effects under normal conditions of use and also under abnormal conditions likely to arise in service.
Arcing Effects: Arcing effects and potential blast damage.
Classification: Classification by type, size, voltage, current capacity, and specific use.
Other Factors: Other factors that contribute to the practical safeguarding of persons using or likely to come in contact with the equipment.
The Mandatory Listing Rule (NEC 110.3(B))
NEC 110.3(B) is one of the most cited enforcement tools in the electrical industry:
"Equipment that is listed, labeled, or both, shall be installed and used in accordance with any instructions included in the listing or labeling."
If a luminaire manufacturer states "maximum 60W lamp," installing a 100W lamp violates 110.3(B). If a panelboard directory card states "tighten lug to 45 in-lbs," tightening to 25 in-lbs violates 110.3(B). If a disconnect enclosure is listed solely for NEMA 1 (dry indoor locations), mounting it outdoors in a Colorado snowstorm violates 110.3(B).
Mechanical Execution of Work & Enclosure Integrity (NEC 110.12)
NEC 110.12 mandates that electrical equipment shall be installed in a neat and workmanlike manner .
Unused Openings (NEC 110.12(A)): Unused openings in boxes, raceways, auxiliary gutters, cabinets, and cutout boxes shall be effectively closed to afford protection substantially equivalent to the wall of the equipment . Where metallic plugs or plates are used with nonmetallic enclosures, they must be recessed at least 1/4 inch from the outer surface.
Integrity of Electrical Equipment (NEC 110.12(B)): Internal parts of electrical equipment, including busbars, wiring terminals, insulators, and other surfaces, shall not be damaged or contaminated by foreign materials such as paint, plaster, cleaners, abrasives, or corrosive residues. There shall be no damaged parts that adversely affect safe operation (e.g., bent or broken parts, cut or sheared insulation).
Electrical Connections & Conductor Terminations (NEC 110.14)
Electrical connections must provide secure, low-resistance joints that withstand operational heating without degradation.
Dissimilar Metals (NEC 110.14): Conductors of dissimilar metals (such as copper and aluminum) shall not be intermixed in a terminal or splicing connector where physical contact occurs between them, unless the device is identified for the purpose and conditions of use. Look for AL/CU or CO/ALR markings on terminals and wire nuts.
Tightening Torque (NEC 110.14(D)): Where a tightening torque is indicated as a numeric value on equipment or in installation instructions provided by the manufacturer, a calibrated torque tool shall be used to achieve the indicated torque value, unless the equipment manufacturer has provided alternative instructions.
Conductor Termination Temperature Limits (NEC 110.14(C))
Every electrical circuit is a series chain consisting of three thermal links:
The conductor insulation rating (e.g., 90°C for THHN).
The conductor ampacity based on temperature.
The terminal lug temperature rating on the overcurrent device or utilization equipment (60°C or 75°C).
The fundamental rule of NEC 110.14(C): The temperature rating associated with the ampacity of a conductor must be selected and coordinated so as not to exceed the lowest temperature rating of any connected termination, conductor, or device . TERMINAL COORDINATION RULES
- [NEC 110.14(C)]
- │
- ┌────────────────────────┴────────────────────────┐
- ▼ ▼
- CIRCUITS 100A OR LESS, OR CIRCUITS OVER 100A, OR
- CONDUCTORS 14 AWG THROUGH 1 AWG CONDUCTORS LARGER THAN 1 AWG
- [110.14(C)(1)(a)] [110.14(C)(1)(b)]
- │ │
- ▼ ▼
- DEFAULT TERMINAL RATING: 60°C • DEFAULT TERMINAL RATING: 75°C
- Must size conductor using • Size conductor using 75°C
60°C column of Table 310.16. column of Table 310.16.
- EXCEPTION: If equipment and • May use 90°C rated conductor
- terminals are listed and marked for ampacity adjustment and
- for 75°C, 75°C column may correction, but final ampacity
be used! is capped at the 75°C column.
The 100-Ampere Rule (NEC 110.14(C)(1)(a))
For equipment rated 100 amperes or less, or marked for conductors 14 AWG through 1 AWG:
Conductors must be evaluated using the 60°C column of Table 310.16.
Permitted exception: Conductors with higher temperature ratings (such as 75°C or 90°C) are permitted to be used, but their ampacity must be based on the 60°C column— unless the equipment terminals are listed and marked for use with 75°C conductors (110.14(C)(1)(a)(3)).
In modern commercial installations, most breakers and panelboard lugs are marked 60°C/75°C or 75°C , which permits the use of the 75°C column. However, on residential switches, standard 15A/20A duplex receptacles, and unmarked devices, the terminals are rated 60°C !
Circuits Over 100 Amperes (NEC 110.14(C)(1)(b))
For equipment rated over 100 amperes, or marked for conductors larger than 1 AWG:
Termination provisions default to the 75°C rating .
Conductors must be evaluated using the 75°C column of Table 310.16 unless specifically listed and marked for higher temperatures.
The 90°C Conductor Derating Principle (Crucial Exam Concept)
Almost all modern commercial building wire installed today is rated 90°C (such as THHN, THWN-2, and XHHW-2 ). However, standard circuit breaker lugs and equipment terminals are rated at 75°C (or 60°C for small residential equipment). This raises a vital question:
If the terminal is only rated 75°C, why install 90°C wire?
The Rule: Conductors with 90°C insulation are permitted to utilize their higher 90°C ampacity value from Table 310.16 as the starting point for ampacity adjustments (bundling) and ambient temperature corrections . However, the final calculated ampacity can never exceed the conductor ampacity in the temperature column corresponding to the terminal rating (75°C) .
Step-by-Step Exam Calculation Example:
Scenario: Four #3 AWG THHN copper current-carrying conductors are installed in EMT raceway through an industrial plant in Pueblo, Colorado, where the ambient temperature reaches 40°C (104°F). The circuit is protected by a 100A circuit breaker with lugs marked 75°C. What is the maximum allowable ampacity of the #3 AWG THHN conductors under these conditions?
Find Table 310.16 Values for #3 AWG Copper:
- 60°C Column = 85 A
- 75°C Column = 100 A (Terminal Limit)
- 90°C Column = 115 A (Starting Point for Derating)
Determine Adjustment & Correction Factors:
Bundling (Table 310.15(C)(1)): 4 current-carrying conductors in raceway = 80% (0.80) adjustment factor.
Ambient Temperature Correction (Table 310.16 Correction Table): At 40°C ambient for a 90°C conductor, the correction factor = 0.91 .
Apply Factors to the 90°C Ampacity: Derated Ampacity = 115 A × 0.80 × 0.91 = 83.72 A \text{Derated Ampacity} = 115\text{ A} \times 0.80 \times 0.91 = 83.72\text{ A} Derated Ampacity = 115 A × 0.80 × 0.91 = 83.72 A
Compare Against the 75°C Terminal Limit:
The terminal rating limit for #3 AWG at 75°C is 100 A .
Since the derated ampacity of 83.7 A is less than the 75°C terminal limit of 100 A, the conductor's allowable ampacity under these conditions of use is 83.7 A .
(Notice: If ambient was 30°C and no bundling applied, the 90°C value would be 115A, but you could only carry 100A due to the 75°C terminal rating!).