Study guide
12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection
Colorado Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Colorado Electrical Licensing Laws, DORA Rules & Exam Logistics
1.1 Colorado Electrical Board, Licensure Tiers & Application Process 1.2 Senate Bill 25-165, Apprentice Supervision & Colorado Board Rules 1.3 Permitting, Inspection Procedures, Violations & Penalties 1.4 The Colorado PSI Exam: Open-Book Format, Time Management & Code Navigation
2 Chapter 2: Electrical Theory, Mathematics & Fundamental Concepts
2.1 Ohm's Law, Joule's Law & DC Circuit Analysis 2.2 AC Fundamentals: Inductance, Capacitance & Power Factor 2.3 Three-Phase Electrical Systems: Wye & Delta Configurations 2.4 Voltage Drop Principles & Single/Three-Phase Formulas
3 Chapter 3: General Installation Requirements — NEC Articles 90 & 110
3.1 NEC Structure, Arrangement & Article 90 Fundamentals 3.2 Key Article 100 Definitions for the Exam 3.3 Equipment Examination, Listing & Termination Temperature Limits 3.4 Working Space, Dedicated Electrical Space & Guarding
4 Chapter 4: Branch Circuits & Feeders — NEC Articles 210, 215 & 225
4.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Branch Circuits 4.2 Dwelling Unit Required Outlets & Receptacle Placement 4.3 Ground-Fault Circuit-Interrupter (GFCI) Protection 4.4 Arc-Fault Circuit-Interrupter (AFCI) Protection & Feeder Rules
5 Chapter 5: Services & Overcurrent Protection — NEC Articles 230, 240 & 242
5.1 Service Conductors, Clearances & Overhead/Underground Drops 5.2 Service Disconnecting Means, Ratings & Surge Protection 5.3 Overcurrent Protection Fundamentals & Standard Ratings 5.4 Feeder & Transformer Tap Rules
6 Chapter 6: Grounding and Bonding — NEC Article 250 Part I (Systems & Electrodes)
6.1 Grounding vs. Bonding: Principles, Functions & Article 250 Architecture 6.2 Grounded Conductors, Main Bonding Jumpers & System Bonding Jumpers 6.3 The Grounding Electrode System 6.4 Grounding Electrode Conductor (GEC) Sizing & Installation
7 Chapter 7: Grounding and Bonding — NEC Article 250 Part II (Equipment & Special Systems)
7.1 Equipment Grounding Conductors (EGC) Types & Identification 7.2 Sizing the Equipment Grounding Conductor 7.3 Separately Derived Systems 7.4 Grounding & Bonding at Separate Buildings or Structures
8 Chapter 8: Wiring Methods & Materials — NEC Chapter 3
8.1 General Wiring Requirements & Underground Installations 8.2 Nonmetallic and Armored Cable Assemblies 8.3 Metallic and Nonmetallic Raceways 8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways
9 Chapter 9: Conductors, Ampacity & Wire Sizing — NEC Article 310
9.1 Conductor Properties, Insulation Types & NEC Table 310.16 9.2 Temperature Correction Factors 9.3 Conductor Bundling & Adjustment Factors 9.4 Comprehensive Conductor Sizing & Terminal Temperature Coordination
10 Chapter 10: Box Fill, Conduit Fill & Pull Box Calculations
10.1 Outlet and Device Box Fill Calculations — NEC 314.16(A) & (B) 10.2 Conduit Fill Calculations — Chapter 9 Tables 1, 4, 5 & Annex C 10.3 Pull and Junction Box Sizing for Conductors 4 AWG and Larger — NEC 314.28 10.4 Practical Enclosure & Raceway Sizing Exam Scenarios
11 Chapter 11: Load Calculations — Dwellings & Commercial Buildings — NEC Article 120
11.1 General Lighting, Small Appliance & Laundry Loads 11.2 Fixed Appliances, Dryers & Cooking Equipment Calculations 11.3 Standard vs. Optional Calculation Methods for Single-Family Dwellings 11.4 Commercial & Multifamily Load Calculations
12 Chapter 12: Motors, Motor Circuits & Controllers — NEC Article 430
12.1 Motor Nameplate vs. NEC Tables & Motor Full-Load Current 12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection 12.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 12.4 Motor Feeders, Disconnecting Means & Controllers
13 Chapter 13: Transformers, Distribution & Utilization Equipment
13.1 Transformer Overcurrent Protection & Installation — NEC Article 450 13.2 Panelboards, Switchboards & Switchgear — NEC Article 408 13.3 Luminaires, Appliances & Fixed Electric Space Heating 13.4 Generators, Transfer Switches & Standby Systems
14 Chapter 14: Special Occupancies, Renewable Energy & Modern Technologies
14.1 Hazardous (Classified) Locations — NEC Articles 500-516 14.2 Health Care Facilities & Places of Assembly — NEC Articles 517 & 518 14.3 Swimming Pools, Spas, Hot Tubs & Fountains — NEC Article 680 14.4 Solar Photovoltaic (PV) Systems & Energy Storage — NEC Articles 690, 705 & 706
12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection
Key Takeaways Explain This Topic AI
Under NEC 430.22, branch-circuit conductors supplying a single continuous-duty motor must have an ampacity of not less than 125% of the motor Full-Load Current (FLC) obtained from NEC Table 430.248 or 430.250.
Conductor sizing must coordinate terminal temperature limitations under NEC 110.14(C) with temperature correction (Table 310.16) and raceway fill adjustment factors (Table 310.15(C)(1)).
Non-continuous duty motors (short-time, intermittent, periodic, or varying duty) are sized according to the percentage multipliers in NEC Table 430.22(E), which range from 85% to 200% of nameplate current.
Separate motor overload protection devices under NEC 430.32(A)(1) are sized at a maximum of 125% of nameplate FLA for motors with a Service Factor (SF) >= 1.15 or marked temperature rise <= 40°C, and 115% for all other motors.
Under NEC 430.34, if the standard overload relay cannot start the motor, the trip rating may be modified up to an absolute ceiling of 140% for motors with SF >= 1.15 or temp rise <= 40°C, and 130% for all others.
Last updated: September 2026
12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection
Exam Fast Fact: When sizing branch-circuit conductors for a single continuous-duty motor under NEC 430.22 , you must multiply the Table FLC by 125% (1.25) . When sizing separate overload protection for the same motor under NEC 430.32(A)(1) , you multiply the Nameplate FLA by either 125% (if Service Factor >= 1.15 or temperature rise <= 40°C) or 115% (all other motors). Never mix these two multipliers or their current bases!
A complete motor branch circuit requires two distinct levels of thermal and overcurrent protection operating in tandem. The conductors must be capable of carrying sustained operating currents plus starting transients without thermal degradation. Concurrently, the motor windings require a sensitive thermal protective device—the overload relay —calibrated to trip when mechanical friction, motor stalling, single-phasing, or sustained mechanical overload draws excessive current through the copper windings.
Sizing Motor Branch-Circuit Conductors: NEC 430.22
Branch-circuit conductors supplying a single motor used in a continuous-duty application must have an ampacity of not less than 125 percent of the motor's full-load current rating as determined by NEC 430.6(A)(1) (NEC Tables 430.247–430.250).
- Minimum Conductor Ampacity = Table FLC * 1.25
- Why the 125% Multiplier is Mandated
Continuous-duty motors generate continuous heat in upstream distribution conductors. Because a motor circuit frequently operates for hours under full mechanical load, the conductors are treated identically to continuous loads under NEC 210.19(A) and 215.2(A). Furthermore, the 125% headroom ensures that normal starting currents and minor voltage variations do not cause conductor temperatures to exceed their insulation ratings.
Step-by-Step Conductor Sizing Example
Problem: Determine the minimum copper conductor size (THHN/THWN-2) for a 10 HP, 208-volt, 3-phase squirrel-cage induction motor operating under continuous duty. Assume terminations are rated for 75°C per NEC 110.14(C).
- Step 1 — Find Table FLC: Open NEC Table 430.250. Look up 10 HP under the 208V column. Table FLC = 30.8 A
- Step 2 — Apply NEC 430.22 Multiplier: Minimum Required Ampacity = 30.8 A * 1.25 = 38.5 A
Step 3 — Select Conductor from Table 310.16:
Check the 75°C column of Table 310.16 for copper conductors:
10 AWG copper has an ampacity of 35 A (insufficient, 35 A < 38.5 A).
8 AWG copper has an ampacity of 50 A (compliant, 50 A >= 38.5 A).
Conclusion: The minimum permissible branch-circuit conductor is 8 AWG Copper THHN/THWN-2 .
Terminal Temperature Limitations & Derating Integration
When sizing motor conductors, electricians must strictly adhere to NEC 110.14(C) termination provisions while factoring in ambient temperature correction and conduit fill adjustments:
NEC 110.14(C)(1)(a): Circuits rated 100 amperes or less, or marked for 14 AWG through 1 AWG conductors, must be sized using the 60°C column of Table 310.16, unless the equipment and terminals are listed and marked for 75°C.
Modern Motor Equipment: Standard industrial motor control centers, across-the-line starters, and molded-case circuit breakers are almost universally listed for 75°C terminations . Motor lead junction boxes (peckerheads) are typically rated for 75°C or 90°C. Therefore, unless an exam question specifies 60°C terminals, standard commercial/industrial practice coordinates with the 75°C column for final ampacity selection.
Derating Rule: If derating factors apply (such as more than 3 current-carrying conductors in a raceway per Table 310.15(C)(1), or elevated ambient temperatures per Table 310.16), you begin derating from the 90°C column for THHN wire, but the final derated ampacity must not exceed the conductor's 75°C terminal rating or drop below the 125% FLC requirement.
Non-Continuous & Duty-Cycle Motors: NEC Table 430.22(E)
Not all motors run continuously. Equipment such as freight elevators, cranes, hoists, drawbridges, and motorized gate valves operate intermittently. Sizing conductors for these applications using the continuous 125% rule would result in massive, unnecessary copper over-sizing.
Under NEC 430.22(E) , conductors supplying motors operating on short-time, intermittent, periodic, or varying duty are sized using the percentage multipliers found in Table 430.22(E) applied to the motor nameplate current rating :
Classification of Service 5-Minute Rated Motor 15-Minute Rated Motor 30- & 60-Minute Rated Motor Continuous Rated Motor
- Short-Time Duty (e.g., operating valves, raising/lowering rolls) 110% 120% 150% —
- Intermittent Duty (e.g., freight elevators, shop cranes, tool heads) 85% 85% 90% 140%
- Periodic Duty (e.g., pumps, compressors with regular cycles) 85% 90% 95% 140%
- Varying Duty (e.g., heavy industrial processes with wild load swings) 110% 120% 150% 200%
- Motor Overload Protection: NEC Article 430 Part III
Motor overload protection guards against excessive heating caused by sustained mechanical loads, operating over full load rating, electrical undervoltage, single-phasing on 3-phase systems, or bearing failure.
Critical Difference: An overload is an operating overcurrent condition that stays within normal conduction paths (not a short circuit or ground fault). Overloads develop heat slowly over seconds or minutes. Branch-circuit short-circuit devices (breakers and fuses) are sized much too high (175% to 300%) to sense low-grade overloads. Without a dedicated overload device, a motor drawing 135% of its rated current would overheat and catch fire long before the branch breaker tripped.
Overload Sizing Rules: NEC 430.32(A)(1)
For continuous-duty motors rated more than 1 horsepower, separate overload devices (such as thermal overload relays, heaters, or electronic overcurrent relays) are sized based on the nameplate full-load current (FLA) according to a strict two-tier percentage criteria:
Maximum Overload Trip Setting = Nameplate FLA * Percentage
Motor Characteristic / Rating Overload Multiplier (NEC 430.32(A)(1)) Description
Motors with Service Factor (SF) >= 1.15 125% (1.25) The motor is engineered with an internal 15% thermal reserve margin.
Motors with Marked Temperature Rise <= 40°C 125% (1.25) Class A or low-temperature Class B insulation profile with superior heat dissipation.
All Other Motors (SF < 1.15, Temp Rise > 40°C, or unmarked) 115% (1.15) Standard motors with minimal thermal cushion; strict 15% overload ceiling.
Step-by-Step Overload Calculation Example
Problem: A 3-phase, 460V, 25 HP induction motor has a nameplate rating of 30.0 A , a marked Service Factor of 1.15 , and a marked temperature rise of 40°C . Table 430.250 lists an FLC of 34.0 A. What is the maximum initial overload protection device rating permitted under NEC 430.32(A)(1)?
Identify the correct current base: Sizing overloads mandates using Nameplate FLA = 30.0 A. (Discard the 34.0 A table value).
Identify the motor's thermal rating: The motor has a Service Factor of 1.15 (and a temperature rise of 40°C). This qualifies for the 125% tier.
- Calculate maximum overload rating: Overload Setting = 30.0 A * 1.25 = 37.5 A
- Maximum Modification of Overload Devices: NEC 430.34
In field installations, a motor driving a high-inertia load (such as a large centrifugal exhaust blower or heavy industrial flywheel) may take a long time to accelerate up to operating speed. The sustained starting current may cause the standard 115% or 125% overload device to trip before the motor reaches full running speed.
To address this nuisance tripping, NEC 430.34 permits selecting the next higher size overload relay or increasing the trip setting, subject to an absolute statutory ceiling :
- Motor Classification Standard Max Overload (NEC 430.32) Absolute Maximum Modification (NEC 430.34)
- Service Factor >= 1.15 125% 140% of Nameplate FLA
- Marked Temp Rise <= 40°C 125% 140% of Nameplate FLA
- All Other Motors (SF 1.0, etc.) 115% 130% of Nameplate FLA
Exam Trap Alert: The 140% and 130% values in NEC 430.34 are exceptions , not initial sizing values! You can never jump directly to 140% or 130% on a test question unless the question explicitly states that the standard overload device selected under 430.32 was insufficient to start the motor or carry the load.
Common Exam Traps & Practical Scenarios
Scenario Correct Application Common Trap
Conductor vs. Overload Multiplier: Sizing a branch circuit for a 5 HP motor with SF 1.0. Conductors = Table FLC * 125%. Overload = Nameplate FLA * 115%. Using 115% for conductors, or using 125% for overloads when SF is 1.0.
Overload Starting Failure: A motor with SF 1.0 trips its 115% overload during starting. Electrician wants to increase setting. Under 430.34, maximum increase is 130% of nameplate FLA. Selecting 140% because they forgot the motor has a 1.0 Service Factor.
Multispeed Motor Conductors (430.22(B)): Conductors between the controller and motor. Must be sized at 125% of the FLC for the highest-speed winding or highest current rating. Sizing conductors only for the low-speed winding because it runs more frequently.