Study guide
13.2 Panelboards, Switchboards & Switchgear — NEC Article 408
Colorado Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Colorado Electrical Licensing Laws, DORA Rules & Exam Logistics
1.1 Colorado Electrical Board, Licensure Tiers & Application Process 1.2 Senate Bill 25-165, Apprentice Supervision & Colorado Board Rules 1.3 Permitting, Inspection Procedures, Violations & Penalties 1.4 The Colorado PSI Exam: Open-Book Format, Time Management & Code Navigation
2 Chapter 2: Electrical Theory, Mathematics & Fundamental Concepts
2.1 Ohm's Law, Joule's Law & DC Circuit Analysis 2.2 AC Fundamentals: Inductance, Capacitance & Power Factor 2.3 Three-Phase Electrical Systems: Wye & Delta Configurations 2.4 Voltage Drop Principles & Single/Three-Phase Formulas
3 Chapter 3: General Installation Requirements — NEC Articles 90 & 110
3.1 NEC Structure, Arrangement & Article 90 Fundamentals 3.2 Key Article 100 Definitions for the Exam 3.3 Equipment Examination, Listing & Termination Temperature Limits 3.4 Working Space, Dedicated Electrical Space & Guarding
4 Chapter 4: Branch Circuits & Feeders — NEC Articles 210, 215 & 225
4.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Branch Circuits 4.2 Dwelling Unit Required Outlets & Receptacle Placement 4.3 Ground-Fault Circuit-Interrupter (GFCI) Protection 4.4 Arc-Fault Circuit-Interrupter (AFCI) Protection & Feeder Rules
5 Chapter 5: Services & Overcurrent Protection — NEC Articles 230, 240 & 242
5.1 Service Conductors, Clearances & Overhead/Underground Drops 5.2 Service Disconnecting Means, Ratings & Surge Protection 5.3 Overcurrent Protection Fundamentals & Standard Ratings 5.4 Feeder & Transformer Tap Rules
6 Chapter 6: Grounding and Bonding — NEC Article 250 Part I (Systems & Electrodes)
6.1 Grounding vs. Bonding: Principles, Functions & Article 250 Architecture 6.2 Grounded Conductors, Main Bonding Jumpers & System Bonding Jumpers 6.3 The Grounding Electrode System 6.4 Grounding Electrode Conductor (GEC) Sizing & Installation
7 Chapter 7: Grounding and Bonding — NEC Article 250 Part II (Equipment & Special Systems)
7.1 Equipment Grounding Conductors (EGC) Types & Identification 7.2 Sizing the Equipment Grounding Conductor 7.3 Separately Derived Systems 7.4 Grounding & Bonding at Separate Buildings or Structures
8 Chapter 8: Wiring Methods & Materials — NEC Chapter 3
8.1 General Wiring Requirements & Underground Installations 8.2 Nonmetallic and Armored Cable Assemblies 8.3 Metallic and Nonmetallic Raceways 8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways
9 Chapter 9: Conductors, Ampacity & Wire Sizing — NEC Article 310
9.1 Conductor Properties, Insulation Types & NEC Table 310.16 9.2 Temperature Correction Factors 9.3 Conductor Bundling & Adjustment Factors 9.4 Comprehensive Conductor Sizing & Terminal Temperature Coordination
10 Chapter 10: Box Fill, Conduit Fill & Pull Box Calculations
10.1 Outlet and Device Box Fill Calculations — NEC 314.16(A) & (B) 10.2 Conduit Fill Calculations — Chapter 9 Tables 1, 4, 5 & Annex C 10.3 Pull and Junction Box Sizing for Conductors 4 AWG and Larger — NEC 314.28 10.4 Practical Enclosure & Raceway Sizing Exam Scenarios
11 Chapter 11: Load Calculations — Dwellings & Commercial Buildings — NEC Article 120
11.1 General Lighting, Small Appliance & Laundry Loads 11.2 Fixed Appliances, Dryers & Cooking Equipment Calculations 11.3 Standard vs. Optional Calculation Methods for Single-Family Dwellings 11.4 Commercial & Multifamily Load Calculations
12 Chapter 12: Motors, Motor Circuits & Controllers — NEC Article 430
12.1 Motor Nameplate vs. NEC Tables & Motor Full-Load Current 12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection 12.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 12.4 Motor Feeders, Disconnecting Means & Controllers
13 Chapter 13: Transformers, Distribution & Utilization Equipment
13.1 Transformer Overcurrent Protection & Installation — NEC Article 450 13.2 Panelboards, Switchboards & Switchgear — NEC Article 408 13.3 Luminaires, Appliances & Fixed Electric Space Heating 13.4 Generators, Transfer Switches & Standby Systems
14 Chapter 14: Special Occupancies, Renewable Energy & Modern Technologies
14.1 Hazardous (Classified) Locations — NEC Articles 500-516 14.2 Health Care Facilities & Places of Assembly — NEC Articles 517 & 518 14.3 Swimming Pools, Spas, Hot Tubs & Fountains — NEC Article 680 14.4 Solar Photovoltaic (PV) Systems & Energy Storage — NEC Articles 690, 705 & 706
13.2 Panelboards, Switchboards & Switchgear — NEC Article 408
Key Takeaways Explain This Topic AI
Under NEC 408.36, each panelboard must be individually protected on its supply side by an overcurrent protective device with a rating not exceeding the nominal rating of the panelboard busbars.
Under NEC 408.36(A), panelboards equipped with snap switches rated 30A or less must have upstream overcurrent protection of not more than 200 amperes.
Under NEC 408.36(D), plug-in circuit breakers that are back-fed from an alternate source (such as solar or standby generation) MUST be secured by an additional approved fastener, such as a mechanical tie-down kit.
NEC 408.4(A) mandates that every circuit and circuit modification must be legibly identified with its clear, evident, and specific purpose; transient descriptions and tenant names are strictly prohibited, and breakers without field conductors must be labeled 'Unused' rather than 'Spare'.
Under NEC 408.3(E)(1) and 110.15, in a 120/240V 4-wire delta system, the high leg (carrying 208V to neutral) must connect to Phase B (the center bus) in all panelboards and switchboards and be marked with an orange finish.
Last updated: September 2026
13.2 Panelboards, Switchboards & Switchgear — NEC Article 408
Exam Fast Fact: Two Article 408 questions appear with high frequency on the Colorado Journeyman exam: (1) NEC 408.36(D) mandates that any plug-in circuit breaker that is back-fed must be secured by an additional approved fastener (tie-down kit) requiring a tool for removal. (2) In a 120/240V 4-wire delta system, NEC 408.3(E)(1) requires the high leg (208V to ground) to connect to the B-phase (center bus) of panelboards and switchboards, and NEC 110.15 requires it to be permanently identified with an orange finish.
Panelboards, switchboards, and switchgear represent the central nervous system of interior electrical distribution. They receive bulk electrical power from utility services or transformers and subdivide that power into smaller feeder and branch circuits. Because these assemblies concentrate enormous available fault energy and expose busbars to thermal and mechanical electrodynamic forces during short circuits, National Electrical Code (NEC) Article 408 rigorously regulates their bus ratings, overcurrent protection, mechanical fastener integrity, directory markings, and internal phase arrangements.
Equipment Definitions: Distinguishing the Big Three (Article 100 & Article 408)
Journeyman electricians must clearly distinguish between the three primary categories of distribution assemblies:
Distribution Equipment Enclosure & Mounting Accessibility & Construction Primary NEC Article
Panelboard Mounted in a cabinet or cutout box; placed against or flush in a wall. Accessible only from the front ; includes busbars and automatic overcurrent protective devices. NEC Article 408 (Part III)
Switchboard Large freestanding structural frame or assembly of panels; floor-mounted. Accessible from the rear as well as the front ; contains switches, overcurrent devices, buses, and instrumentation. Not enclosed in cabinets. NEC Article 408 (Part II)
Switchgear Completely enclosed on all sides and top with sheet metal; compartmentalized. Contains primary power circuit switching and interrupting devices (such as drawout power circuit breakers) with isolated bus compartments. NEC Article 408 (Part II) & Article 490
Busbar Ampere Ratings (NEC 408.30)
Under NEC 408.30 , a panelboard must have an ampere bus rating not less than the minimum feeder capacity required for the calculated load determined in accordance with NEC Article 120. The busbars are manufactured from aluminum or copper and are stamped with a maximum continuous current rating (e.g., 100A, 225A, 400A, 600A, 800A). Operating a panelboard with total continuous and non-continuous loads exceeding its rated bus capacity causes dangerous thermal expansion, metal fatigue, and busbar warping.
Overcurrent Protection of Panelboards (NEC 408.36)
The fundamental rule governing panelboard safety is NEC 408.36 :
"In addition to the requirement of 408.30, a panelboard shall be protected by an overcurrent protective device having a rating not greater than that of the panelboard. This overcurrent protective device shall be located within or at any point on the supply side of the panelboard." SUPPLY FEEDER (From Service or Upstream Transformer)
- |
- +--------------v--------------+
- | 200A Upstream Circuit Breaker|
- +--------------+--------------+
- |
- FEEDER RUN | (Rated 200A)
- |
- +--------------v--------------+
- | Main Lug Only (MLO) Panel |
- | Rated 200A or 225A Busbar | ---> FULLY CODE COMPLIANT
- +-----------------------------+
vs.
- +--------------v--------------+
- | 200A Upstream Circuit Breaker|
- +--------------+--------------+
- |
- FEEDER RUN | (Rated 200A)
- |
- +--------------v--------------+
- | Main Lug Only (MLO) Panel |
| Rated 125A Busbar | ---> VIOLATION OF NEC 408.36!
- +-----------------------------+ (Panel bus can be overloaded)
- Main Breaker Panels vs. Main Lug Only (MLO) Panels
Main Breaker Panelboard: The panel contains an internal integral main circuit breaker on the line side of its busbars. The internal breaker provides the required overcurrent protection, allowing the upstream feeder breaker to have a higher rating if feeding multiple downstream loads.
Main Lug Only (MLO) Panelboard: The panelboard contains no internal main breaker; feeder conductors land directly on mechanical terminal lugs bolted to the bus. An MLO panelboard is legal only if the overcurrent protective device on the upstream supply side has an ampere rating equal to or less than the panelboard bus rating. For example, a 225A MLO panelboard fed from a 200A circuit breaker complies fully with NEC 408.36.
The 200-Ampere Snap Switch Rule (NEC 408.36(A))
A dedicated exam question addresses panelboards containing small lighting switches:
NEC 408.36(A): Panelboards equipped with snap switches rated 30 amperes or less must have overcurrent protection on the supply side rated at not more than 200 amperes .
This rule prevents high-ampere industrial feeders (e.g., 400A or 600A) from feeding panels containing fragile, low-ampere snap switches, which could vaporize during an internal fault before the massive upstream OCPD could trip.
Transformer-Supplied Panelboards (NEC 408.36(B))
Where a panelboard is supplied from the secondary of a transformer, the required overcurrent protection for the panelboard bus must be located on the secondary side of the transformer .
The Rule: You cannot rely on the primary OCPD of a transformer to protect a secondary panelboard, unless the transformer has a 2-wire single-phase secondary or a 3-phase delta-to-delta secondary meeting NEC 240.21(C)(1).
For common 480V to 208Y/120V 3-phase wye transformers, the secondary panelboard must have an individual secondary main breaker (or be protected by a secondary main OCPD) sized not greater than the panelboard bus rating.
Back-Fed Devices & Mandatory Tie-Down Kits (NEC 408.36(D))
In modern electrical construction, circuit breakers are frequently used in reverse: instead of taking power off the busbar to feed a branch load, power is pushed onto the busbar from an alternate source. Common examples include:
Grid-tied photovoltaic (PV) solar inverters.
Standby generator emergency feeds.
Feeder conductors landing in an MLO panel via a converted branch breaker.
The Life-Safety Hazard of Back-Feeding
Standard plug-in circuit breakers clip onto panelboard bus stabs via spring-tensioned copper or bronze jaws. They are designed so an electrician can pull them straight off the bus with their hands when disconnected.
However, when a circuit breaker is back-fed , the load terminals become the line supply . If a maintenance technician or homeowner unlatches the deadfront cover and pulls on the back-fed breaker, the breaker can pop loose from the bus while remaining energized from the solar array or generator. The exposed female metal clips on the rear of the breaker are now live at 120V or 240V to ground , dangling loosely inside the enclosure. Any contact with the metallic panel enclosure, neutral bus, or human hands creates an instant, lethal phase-to-ground fault or arc flash.
The Mandatory Code Requirement
Under NEC 408.36(D) :
"Plug-in-type overcurrent protection devices or plug-in-type main lug assemblies that are back-fed and used to terminate field-installed ungrounded supply conductors shall be secured in place by an additional approved fastener that requires other than a pull to release the device from the mounting means on the panel."
Approved Fasteners: Commonly called a breaker tie-down kit , this hardware consists of a heavy steel retaining bracket secured to the panelboard interior by a threaded machine screw or bolt. Removing the breaker requires a screwdriver or wrench—it cannot be dislodged by hand.
Bolt-on Exception: Bolt-on circuit breakers bolted directly to threaded copper busbars already satisfy this requirement inherently; NEC 408.36(D) applies strictly to plug-in assemblies.
Circuit Directories & Panel Identification (NEC 408.4)
Clear, durable circuit directories are vital for life safety, fire department emergency disconnect operations, and maintenance lockout/tagout (LOTO) protocols.
NEC 408.4(A): Clear, Evident, and Specific Purpose
Every circuit and circuit modification must be legibly identified as to its clear, evident, and specific purpose or use. The Code mandates that the identification must have sufficient detail to allow any person to distinguish each circuit from all other circuits.
Directory Practice Code Status Rationale under NEC 408.4(A)
"Lighting" or "Plugs" VIOLATION Completely ambiguous; does not identify location or specific equipment.
"John's Office Receptacles" VIOLATION Prohibited. NEC 408.4(A) explicitly forbids identification based on transient conditions or temporary occupants .
"North Wall Receptacles - Suite 201" COMPLIANT Clear, permanent, evident, and specific geographic location.
"Rooftop RTU-3 Compressor" COMPLIANT Distinctly identifies the mechanical equipment served.
"Spare" (with no conductors terminated) VIOLATION Breakers without connected field wiring must be labeled "Unused" , not "Spare".
"Spare" (with terminated future conductors) COMPLIANT Permitted only where conductors are physically installed and landed for future expansion.
Source Marking for Switchboards and Panelboards (NEC 408.4(B))
In all commercial, industrial, and institutional occupancies (any building other than one- or two-family dwellings), all switchboards, switchgear, and panelboards supplied by a feeder must be permanently marked with:
The specific equipment or device from which the panelboard is supplied (e.g., "Fed from Switchboard MSB-1, Breaker #4" ).
The exact physical location of that upstream disconnecting device (e.g., "Located in Basement Electrical Room B-02" ).
High-Leg Delta Bus Connections & Phasing (NEC 408.3(E)(1) & 110.15)
The 120/240-volt, 3-phase, 4-wire delta distribution system (commonly referred to as a high-leg , wild-leg , stinger-leg , or red-leg delta ) is widely encountered in older industrial and commercial machine shops throughout Colorado.
Electrical Characteristics of the High-Leg Delta
In this system, the utility connects three single-phase transformer secondaries in a closed delta. One transformer winding (the "lighting pot") has its center tap grounded to create the system neutral:
- Phase A to Neutral: 120 Volts ( 240 V / 2 = 120 V 240\text{ V} / 2 = 120\text{ V} 240 V /2 = 120 V )
- Phase C to Neutral: 120 Volts ( 240 V / 2 = 120 V 240\text{ V} / 2 = 120\text{ V} 240 V /2 = 120 V )
- Phase A to Phase B: 240 Volts (Full line-to-line voltage)
- Phase B to Phase C: 240 Volts (Full line-to-line voltage)
- Phase C to Phase A: 240 Volts (Full line-to-line voltage)
Phase B to Neutral (High Leg): 208 Volts Voltage B − Neutral = 120 V × 3 = 120 V × 1.732 = 207.84 V ≈ 208 Volts \text{Voltage}_{B-\text{Neutral}} = 120\text{ V} \times \sqrt{3} = 120\text{ V} \times 1.732 = 207.84\text{ V} \approx 208\text{ Volts} Voltage B − Neutral = 120 V × 3 = 120 V × 1.732 = 207.84 V ≈ 208 Volts PHASE A (120V to Neutral)
- /\
- / \
- / \
- 240V Winding / \ 240V Winding
- / \
- / \
- NEUTRAL (Center) /__ __ __ __ \ PHASE B (High Leg: 208V to Neutral)
- \ /
- \ /
- \ / 240V Winding
- \ /
- \ /
- \ /
- \ /
- PHASE C (120V to Neutral)
- Mandatory Bus Arrangement (NEC 408.3(E)(1))
To establish nationwide uniformity and prevent catastrophic errors:
Under NEC 408.3(E)(1) , the phase bus possessing the higher voltage to ground ( the high leg ) MUST be connected to the B-phase (center bus) of all panelboards, switchboards, and switchgear.
Standard bus phasing orientation is A, B, C from left to right, top to bottom, or front to back when viewed from the front of the equipment.
The Metering Exception: The single exception in the NEC permits the high leg to be located on a phase other than B-phase in metering equipment , where local electric utilities frequently mandate the high leg to land on the far right (Phase C) of the meter socket.
Mandatory Identification & Orange Finish (NEC 110.15)
Under NEC 110.15 , on a 4-wire, delta-connected system where the midpoint of one phase winding is grounded, the conductor or busbar having the higher phase voltage to ground must be legibly and permanently identified by an outer finish that is ORANGE in color , or by tagging or other effective means, at every point where a connection is made if the grounded (neutral) conductor is present.
The Extreme Jobsite Danger
If an electrician fails to land the high leg on B-phase or fails to mark it with orange tape, an apprentice installing a single-pole 120V breaker could snap it into the high leg. The circuit would deliver 208 volts across 120-volt rated loads (computers, LED drivers, televisions, or fractional horsepower motors), instantly causing catastrophic component blowout, smoke, and fire.