Study guide
8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways
Colorado Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Colorado Electrical Licensing Laws, DORA Rules & Exam Logistics
1.1 Colorado Electrical Board, Licensure Tiers & Application Process 1.2 Senate Bill 25-165, Apprentice Supervision & Colorado Board Rules 1.3 Permitting, Inspection Procedures, Violations & Penalties 1.4 The Colorado PSI Exam: Open-Book Format, Time Management & Code Navigation
2 Chapter 2: Electrical Theory, Mathematics & Fundamental Concepts
2.1 Ohm's Law, Joule's Law & DC Circuit Analysis 2.2 AC Fundamentals: Inductance, Capacitance & Power Factor 2.3 Three-Phase Electrical Systems: Wye & Delta Configurations 2.4 Voltage Drop Principles & Single/Three-Phase Formulas
3 Chapter 3: General Installation Requirements — NEC Articles 90 & 110
3.1 NEC Structure, Arrangement & Article 90 Fundamentals 3.2 Key Article 100 Definitions for the Exam 3.3 Equipment Examination, Listing & Termination Temperature Limits 3.4 Working Space, Dedicated Electrical Space & Guarding
4 Chapter 4: Branch Circuits & Feeders — NEC Articles 210, 215 & 225
4.1 Branch-Circuit Ratings, Conductor Sizing & Multiwire Branch Circuits 4.2 Dwelling Unit Required Outlets & Receptacle Placement 4.3 Ground-Fault Circuit-Interrupter (GFCI) Protection 4.4 Arc-Fault Circuit-Interrupter (AFCI) Protection & Feeder Rules
5 Chapter 5: Services & Overcurrent Protection — NEC Articles 230, 240 & 242
5.1 Service Conductors, Clearances & Overhead/Underground Drops 5.2 Service Disconnecting Means, Ratings & Surge Protection 5.3 Overcurrent Protection Fundamentals & Standard Ratings 5.4 Feeder & Transformer Tap Rules
6 Chapter 6: Grounding and Bonding — NEC Article 250 Part I (Systems & Electrodes)
6.1 Grounding vs. Bonding: Principles, Functions & Article 250 Architecture 6.2 Grounded Conductors, Main Bonding Jumpers & System Bonding Jumpers 6.3 The Grounding Electrode System 6.4 Grounding Electrode Conductor (GEC) Sizing & Installation
7 Chapter 7: Grounding and Bonding — NEC Article 250 Part II (Equipment & Special Systems)
7.1 Equipment Grounding Conductors (EGC) Types & Identification 7.2 Sizing the Equipment Grounding Conductor 7.3 Separately Derived Systems 7.4 Grounding & Bonding at Separate Buildings or Structures
8 Chapter 8: Wiring Methods & Materials — NEC Chapter 3
8.1 General Wiring Requirements & Underground Installations 8.2 Nonmetallic and Armored Cable Assemblies 8.3 Metallic and Nonmetallic Raceways 8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways
9 Chapter 9: Conductors, Ampacity & Wire Sizing — NEC Article 310
9.1 Conductor Properties, Insulation Types & NEC Table 310.16 9.2 Temperature Correction Factors 9.3 Conductor Bundling & Adjustment Factors 9.4 Comprehensive Conductor Sizing & Terminal Temperature Coordination
10 Chapter 10: Box Fill, Conduit Fill & Pull Box Calculations
10.1 Outlet and Device Box Fill Calculations — NEC 314.16(A) & (B) 10.2 Conduit Fill Calculations — Chapter 9 Tables 1, 4, 5 & Annex C 10.3 Pull and Junction Box Sizing for Conductors 4 AWG and Larger — NEC 314.28 10.4 Practical Enclosure & Raceway Sizing Exam Scenarios
11 Chapter 11: Load Calculations — Dwellings & Commercial Buildings — NEC Article 120
11.1 General Lighting, Small Appliance & Laundry Loads 11.2 Fixed Appliances, Dryers & Cooking Equipment Calculations 11.3 Standard vs. Optional Calculation Methods for Single-Family Dwellings 11.4 Commercial & Multifamily Load Calculations
12 Chapter 12: Motors, Motor Circuits & Controllers — NEC Article 430
12.1 Motor Nameplate vs. NEC Tables & Motor Full-Load Current 12.2 Sizing Motor Branch-Circuit Conductors & Overload Protection 12.3 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection 12.4 Motor Feeders, Disconnecting Means & Controllers
13 Chapter 13: Transformers, Distribution & Utilization Equipment
13.1 Transformer Overcurrent Protection & Installation — NEC Article 450 13.2 Panelboards, Switchboards & Switchgear — NEC Article 408 13.3 Luminaires, Appliances & Fixed Electric Space Heating 13.4 Generators, Transfer Switches & Standby Systems
14 Chapter 14: Special Occupancies, Renewable Energy & Modern Technologies
14.1 Hazardous (Classified) Locations — NEC Articles 500-516 14.2 Health Care Facilities & Places of Assembly — NEC Articles 517 & 518 14.3 Swimming Pools, Spas, Hot Tubs & Fountains — NEC Article 680 14.4 Solar Photovoltaic (PV) Systems & Energy Storage — NEC Articles 690, 705 & 706
8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways
Key Takeaways Explain This Topic AI
Cable trays (NEC Article 392) are structural support systems rather than raceways; single conductors installed in cable tray must be 1/0 AWG or larger and listed/marked for cable tray use ('CT Use') under NEC 392.10(B)(1).
In metal wireways (NEC Article 376), total conductor fill is limited to 20% of the interior cross-sectional area at any cross section under 376.22(A), and splices or taps cannot exceed 75% of the cross section under 376.56(A).
The ampacity adjustment (derating) factors of Table 310.15(C)(1) do not apply to conductors in metal wireways unless the number of current-carrying conductors exceeds 30 at any cross section under NEC 376.22(B).
Auxiliary gutters (NEC Article 366) are limited to a maximum length of 30 feet beyond the equipment they supplement and share the identical 20% conductor fill, 75% splice/tap fill, and 30-conductor derating rules as wireways.
Surface metal raceways (NEC Article 386) provide enclosed surface distribution in dry interior locations; conductor fill is governed by manufacturer listing and cross-sectional testing per NEC 386.22.
Last updated: September 2026
8.4 Cable Trays, Wireways, Auxiliary Gutters & Surface Raceways
Exam Fast Fact: High-density distribution systems provide flexible routing for large quantities of feeders and branch circuits in commercial and industrial settings. On the Colorado Journeyman exam, three critical rules dominate this topic: (1) the metal wireway 20% conductor fill and 75% splice/tap fill limits under NEC 376.22 and 376.56 , (2) the famous "30 Conductor Rule" under NEC 376.22(B) (derating does NOT apply unless there are more than 30 current-carrying conductors), and (3) the 1/0 AWG minimum size for single conductors in cable trays under NEC 392.10(B)(1) .
When industrial manufacturing plants, data centers, hospitals, and high-rise commercial switchgear rooms require routing hundreds of conductors, traditional pipe-and-wire raceways become physically congested and labor-prohibitive. Open and high-density enclosures—cable trays, wireways, auxiliary gutters, and surface raceways—provide accessible, engineered distribution pathways.
Cable Trays (NEC Article 392)
A cable tray system is a unit or assembly of units or sections and associated fittings forming a rigid structural system used to securely fasten or support cables and raceways. CABLE TRAY SYSTEM TYPES
- Ladder Cable Tray Solid-Bottom Cable Tray
- ┌────────────────────┐ ┌────────────────────┐
- │ │ │ │ │ │ │ (Rungs) │ │
- │ │ │ │ │ │ │ │ │ (Solid Sheet)
- └────────────────────┘ └────────────────────┘
- Maximum heat dissipation • Full mechanical protection
- Single conductors ≥ 1/0 AWG • Reduced ampacity ratings
- Easy cable drop-outs • Lower allowable cable fill
- Critical Definition: Support System vs. Raceway
Under NEC Article 100 , a cable tray is classified as a structural support system , not a raceway . Because it is an open support system rather than an enclosed conduit:
Not all conductors permitted in conduits can be laid in cable trays.
General single conductors (such as standard 12 AWG THHN) are strictly prohibited from being installed loose in a cable tray.
Single Conductor Rules (NEC 392.10(B)(1))
Single conductors installed in cable tray must meet three rigid criteria:
Minimum Size: Must be 1/0 AWG or larger .
Listing & Marking: Must be listed and marked on the outer jacket as suitable for cable tray use (marked "CT Use" or "for CT Use" ).
Tray Style: Single conductors 1/0 AWG through 4/0 AWG must be installed in ladder-type cable tray with rung spacing not exceeding 9 inches, or in ventilated trough cable tray. Conductors 250 kcmil and larger may be installed in ladder, ventilated trough, or ventilated channel trays.
Equipment Grounding Conductors: Single-conductor EGCs must be 4 AWG or larger copper or aluminum.
Cable Tray Fill Rules (NEC 392.22)
Cable tray fill rules prevent thermal overheating and mechanical crushing of underlying cables:
Multiconductor Cables Containing 4/0 AWG or Larger (392.22(A)(1)(a)): In ladder or ventilated trough trays, cables containing conductors 4/0 AWG or larger must be installed in a single layer with no stacking. The sum of the cable diameters cannot exceed the cable tray interior width.
Multiconductor Cables Smaller than 4/0 AWG (392.22(A)(1)(b)): Where all multiconductor cables are smaller than 4/0 AWG, the total cross-sectional area of all cables cannot exceed the maximum allowable cable fill area specified in NEC Table 392.22(A) (Column 1).
Solid-Bottom Trays (392.22(A)(3)): Because solid-bottom trays trap heat, the allowable cable fill area is reduced by approximately 20% to 30% compared to ventilated ladder trays.
Ampacity of Conductors in Cable Trays (NEC 392.80)
Multiconductor Cables: Sized using Table 310.16. Where ladder or ventilated trough trays contain multiconductor cables without maintaining spacing, derating factors apply based on tray width.
Single-Conductor Cables Maintained with Spacing (392.80(B)(1)(a)): Where single conductors are installed in a single layer with a maintained minimum spacing of one cable diameter between conductors, allowable ampacities are taken from the free-air tables (NEC Table 310.17) . This provides substantially higher current ratings than conduit tables!
Grounding and Bonding (NEC 392.60)
Metallic cable trays (steel or aluminum) are permitted to serve as the Equipment Grounding Conductor (EGC) provided:
The tray sections and fittings are listed and identified for grounding.
The minimum cross-sectional area of metal meets or exceeds the requirements of NEC Table 392.60(A) .
Cable tray sections, expansion joints, and discontinuous segments are bonded together using listed bonding jumpers sized per Table 250.102(C)(1).
Metal Wireways (NEC Article 376)
Metal wireways are sheet metal troughs with hinged or removable covers for housing and protecting electric wires and cables, installed in exposed commercial and industrial spaces. METAL WIREWAY CROSS-SECTION FILL
- ┌────────────────────────────────────────────────────────┐
- │ 6" x 6" Metal Wireway = 36.0 Square Inches Total Area │
- │ │
- │ ████████ Conductors: Maximum 20% Fill │
- │ ████████ (36.0 sq. in. × 0.20 = 7.20 sq. in.) │
- │ │
- │ ░░░░░░░░░░░░░░░░░░ Splices & Taps: Up to 75% Fill │
- │ ░░░░░░░░░░░░░░░░░░ (36.0 sq. in. × 0.75 = 27.0 sq. in.)│
- └────────────────────────────────────────────────────────┘
- Maximum Conductor Fill (NEC 376.22(A))
The 20% Conductor Rule: "The maximum sum of cross-sectional areas of all contained conductors at any cross section of a wireway shall not exceed 20 percent of the interior cross-sectional area of the wireway."
Worked Example: An electrician installs an 8-inch by 8-inch metal wireway.
Total interior area: 8 in. × 8 in. = 64.0 sq. inches 8\text{ in.} \times 8\text{ in.} = 64.0\text{ sq. inches} 8 in. × 8 in. = 64.0 sq. inches .
Allowable conductor area: 64.0 sq. in. × 0.20 = 12.80 sq. inches 64.0\text{ sq. in.} \times 0.20 = 12.80\text{ sq. inches} 64.0 sq. in. × 0.20 = 12.80 sq. inches .
The sum of conductor cross-sectional areas (calculated using Chapter 9, Table 5) cannot exceed 12.80 square inches.
Splices and Taps Fill Limit (NEC 376.56(A))
Splices and taps are permitted within wireways, provided they are accessible:
The 75% Splice Rule: The conductors, splices, and taps together shall not fill more than 75 percent of the interior cross-sectional area of the wireway at that point.
The "30 Conductor Rule" for Ampacity Derating (NEC 376.22(B))
In standard conduits (such as EMT or PVC), ampacity adjustment factors from Table 310.15(C)(1) begin as soon as more than three current-carrying conductors are installed together. In metal wireways, the code provides a major exception:
NEC 376.22(B) Ampacity Exception: "The adjustment factors specified in 310.15(C)(1) shall not apply to the conductors in wireways unless the number of current-carrying conductors exceeds 30 at any cross section."
Up to 30 Current-Carrying Conductors: Zero derating required! Every conductor carries 100% of its Table 310.16 ampacity (subject to terminal temperature limitations).
More than 30 Current-Carrying Conductors: Once the count reaches 31 or more, the adjustment factors of Table 310.15(C)(1) apply to all current-carrying conductors in that cross section (typically derating to 40% or 35% of their allowable ampacity).
Securing and Supporting (NEC 376.30)
Horizontal wireways must be supported at intervals not exceeding 5 feet (1.5 m) .
Where specially listed for longer spans, support intervals may be extended up to 10 feet (3.0 m) .
Vertical wireways must be supported at intervals not exceeding 15 feet (4.5 m) , with not more than one joint between supports.
Dead ends of wireways must be closed with listed end fittings (NEC 376.58).
Auxiliary Gutters (NEC Article 366)
Auxiliary gutters are sheet metal or nonmetallic enclosures designed to supplement wiring spaces at meter centers, distribution centers, switchboards, and panelboards.
The 30-Foot Length Limitation (NEC 366.12 & 366.20)
A critical distinction between wireways and auxiliary gutters on licensing exams:
Wireways (Article 376): May run indefinitely throughout a building (hundreds of feet across rooms).
Auxiliary Gutters (Article 366): An auxiliary gutter shall not extend a greater distance than 30 feet (9.0 m) beyond the equipment it supplements!
Fill and Derating Parallels
Auxiliary gutters share the exact same mathematical fill and derating thresholds as wireways:
Maximum conductor fill: 20% of interior cross section (NEC 366.22(A)).
Maximum fill at splices and taps: 75% of interior cross section (NEC 366.56(A)).
Ampacity adjustment factors: Apply only when there are more than 30 current-carrying conductors at any cross section (NEC 366.22(B)).
Surface Metal Raceways (NEC Article 386)
Surface metal raceways (frequently called by the brand name "Wiremold") are mounted directly on finished surfaces for commercial remodeling, school computer labs, and office perimeter power.
Uses & Installation Requirements
Uses Permitted (386.10): Permitted only in dry interior locations , exposed on surface walls, floors (where listed), and benches.
Uses Not Permitted (386.12): Concealed within walls or ceilings; where subject to severe physical damage; in damp/wet locations; or where voltage between conductors exceeds 300 volts unless the metal thickness is at least 0.040 inches (1.0 mm).
Conductor Fill (386.22): Number and size of conductors cannot exceed the manufacturer's listing for the specific channel cross section.
Grounding Continuity: All sections, elbows, and device boxes must be mechanically fastened using listed fittings to maintain continuous equipment grounding.
Comprehensive Comparison: Wireways vs. Gutters vs. Trays vs. Surface Raceways
Feature Metal Wireways (Art. 376) Auxiliary Gutters (Art. 366) Cable Trays (Art. 392) Surface Raceways (Art. 386)
- Classification Raceway Enclosure / Supplement Support System (Not a Raceway) Raceway
- Length Limit Unlimited 30 feet maximum Unlimited Unlimited
- Conductor Fill 20% cross-section 20% cross-section Per Table 392.22(A) Per manufacturer listing
- Splices/Taps Fill 75% cross-section 75% cross-section Permitted in trays In approved junction boxes
- Derating Threshold > 30 current-carrying > 30 current-carrying Depends on spacing/layers > 3 current-carrying
Single Conductor Min Any recognized gauge Any recognized gauge 1/0 AWG (Marked CT Use) Per manufacturer listing
- Support Interval 5 ft (up to 10 ft) 5 ft Per manufacturer span Per manufacturer specs
- Practical Jobsite Scenarios & Common Exam Traps
Jobsite Scenario Technical Reality & Code Rule Common PSI Exam Trap
Single Conductors in Cable Tray: An installer runs twenty-four 10 AWG THHN single copper conductors directly in a ladder-type cable tray between panels. Violation of 392.10(B)(1): Single conductors in cable tray must be 1/0 AWG or larger and listed for CT use. 10 AWG must be enclosed in conduit or a cable assembly. Believing any standard building wire can be laid loose in an open cable tray.
24 Conductors in a Metal Wireway: An electrician installs 24 current-carrying 12 AWG THHN conductors in a 4" x 4" metal wireway and applies a 70% derating factor from Table 310.15(C)(1). Unnecessary Derating: Under 376.22(B), derating does not apply unless current-carrying conductors exceed 30 . The conductors maintain 100% allowable ampacity. Assuming the standard conduit rule (> 3 conductors = derating) applies to metal wireways.
Auxiliary Gutter 40-Foot Run: A wireman installs an auxiliary gutter extending 40 feet across a commercial basement to connect three subpanels. Violation of 366.12/366.20: Auxiliary gutters are legally limited to a maximum length of 30 feet . For runs exceeding 30 feet, a metal wireway (Article 376) must be used. Confusing auxiliary gutters with metal wireways and ignoring the 30-foot limit.
Wireway Fill Calculation: An installer calculates wireway fill by packing a 6" x 6" trough to 40% fill, citing Table 1 of Chapter 9 for conduits. Violation of 376.22(A): Conduit fill rules (40%) do not apply to wireways. Conductor fill in metal wireways is strictly capped at 20% of the interior area. Applying conduit fill percentages (40% for 3+ wires) to sheet metal wireways.