Study guide

8.6 Equipment Cleanout, Maintenance & Preventing Carryover Injury

Colorado Pesticide Applicator Certification Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Federal Pesticide Law, Registration & Certification

1.1 Federal Pesticide Laws & FIFRA Framework 1.2 Federal Certification Standards and Supervision of Noncertified Applicators

2 Chapter 2: The Colorado Pesticide Applicators' Act — Licensing, Records & Compliance

2.1 Colorado Pesticide Applicators' Act & Licensing Categories 2.2 Colorado Pest-Management Licensure Categories 2.3 Examinations, Fees, Renewal, Reinstatement & Reciprocity 2.4 Continuing Education Credits and Recertification Subjects 2.5 Technician Training Mandates Under 8 CCR 1203-2 Part 5 2.6 Application Records Under 8 CCR 1203-2 Part 6 2.7 Business Practices: Equipment Identification, Invoices, Insurance & Label Possession 2.8 The Registry of Pesticide-Sensitive Persons and Advance Notification 2.9 Notice-of-Application Signs and Customer Notices 2.10 The Colorado Chemigation Act and Backflow Prevention 2.11 Unlawful Acts, Enforcement, Penalties & License Discipline 2.12 Pesticide Use in Colorado Cannabis Production

3 Chapter 3: Integrated Pest Management, Pest Biology, Pesticide Families & Formulations

3.1 IPM Principles, Scouting & Action Thresholds 3.2 Pest Biology, Morphology & Damage Identification 3.3 Pesticide Formulations, Compatibility & Adjuvants 3.4 Pesticide Types, Chemical Families & Modes of Action

4 Chapter 4: Pesticide Labels, Safety Data Sheets & Regulatory Compliance

4.1 Pesticide Label Interpretation & Legal Mandates 4.2 Signal Words, Precautionary Statements & Toxicity Categories 4.3 Directions for Use, Restrictions & Safety Data Sheets (SDS)

5 Chapter 5: Pesticide Toxicology, Human Health Hazards & First Aid

5.1 Principles of Toxicology, Dose-Response & Chronic Health Risks 5.2 Routes of Exposure, Absorption Rates & Chemical Poisoning Symptoms 5.3 Emergency First Aid, Antidote Protocols & Heat Stress Management

6 Chapter 6: Personal Protective Equipment, Respiratory Protection, WPS & Public Safety

6.1 PPE Selection, Chemical Resistance & Laundering Protocols 6.2 Respiratory Protection, Cartridge Selection & Fit Testing 6.3 EPA Worker Protection Standard (WPS) & Agricultural Employer Duties 6.4 Public Safety: Bystanders, Sensitive Sites, Communication & Chemical Security

7 Chapter 7: Environmental Protection, Water Quality & Drift Management

7.1 Pesticide Environmental Fate & Water Resource Protection 7.2 Spray Drift Mechanics, Droplet Dynamics & Weather Factors 7.3 Pollinator Stewardship & Non-Target Organism Protection 7.4 Endangered Species Act & Colorado Climate Adaptations

8 Chapter 8: Application Equipment, Methods, Calibration & Tank Mixing

8.1 Spray Equipment Systems, Pump Mechanics & Nozzle Technology 8.2 Agricultural Boom Sprayer Calibration & Operating Mathematics 8.3 Turf, Landscape & Granular Application Equipment Calibration 8.4 Tank Mixing Mathematics, Solution Blending & Loading Sequences 8.5 Application Methods, Techniques & Placement Decisions 8.6 Equipment Cleanout, Maintenance & Preventing Carryover Injury

9 Chapter 9: Safe Storage, Transport, Container Disposal & Spill Response

9.1 Pesticide Storage Facility Engineering, Security & Climate Control 9.2 Mixing/Loading Operations, Container Rinsing & Disposal Protocols 9.3 The Three C's of Spill Management & Emergency Reporting Protocols 9.4 Transporting Pesticides Safely and Legally

8.6 Equipment Cleanout, Maintenance & Preventing Carryover Injury

Key Takeaways Explain This Topic AI

Sulfonylurea and growth-regulator herbicide residues can injure a sensitive crop at concentrations far below what any visual inspection would reveal, so cleanout follows the label’s cleaning procedure rather than a rinse by eye.

Cleanout is a full-system job: tank, boom, hoses, filters, screens, nozzle bodies, and the end caps, which is where sediment collects.

Rinsate is a pesticide: it should be applied to a labeled site at or below the label rate rather than discarded, which is the same logic as triple rinsing a container.

Screens run coarse at the tank and fine at the nozzle — typically 16 to 50 mesh at the suction side and 50 to 100 mesh at the nozzle — and mesh must never be finer than the nozzle manufacturer specifies.

A nozzle delivering more than 10 percent above the output of a new tip of the same size at the same pressure must be replaced.

Last updated: August 2026

8.6 Equipment Cleanout, Maintenance & Preventing Carryover Injury

A named competency: Colorado Part 4.39 lists "equipment including: calibration, selection of correct equipment for the job, maintenance and care, clean up , new equipment," and 40 CFR § 171.103(c)(6) requires competency in "the use, maintenance and calibration procedures" for application equipment. Calibration tells you whether the machine is delivering the right amount; cleanout and maintenance decide whether it will still do so tomorrow — and whether the next load injures a crop.

1. Why Carryover Injury Happens

A sprayer is not a clean container. Active ingredient adheres to tank walls, hoses, the inside of the boom, filter housings, and the dead ends beyond the last nozzle. Some chemistries then release slowly into a subsequent load.

Sulfonylurea and other ALS-inhibiting herbicides are applied at fractions of an ounce per acre, so a residue far too dilute to see can still injure a sensitive crop.

Growth-regulator herbicides such as 2,4-D, dicamba, and clopyralid injure grapes, tomatoes, sunflowers, and many ornamentals at very low concentrations.

Oil-based emulsifiable concentrates leave a film that traps residue and can later release it as a slug.

Injury usually shows up as cupping, twisting, or strapping of new growth several days after the second application — by which time the tank has been refilled again and the diagnosis is guesswork. This is why the label's cleaning procedure is a legal instruction, not a housekeeping tip.

  • 2. The Cleanout Sequence ┌─────────────────────────────────────────────────────────────────────────────┐
  • │ SPRAYER CLEANOUT — STANDARD SEQUENCE │
  • ├─────────────────────────────────────────────────────────────────────────────┤
  • │ 0. PPE FIRST. Cleanout exposes you to concentrate, not dilute spray. │
  • │ 1. SPRAY OUT the remaining tank mix on a LABELED SITE at or below the │
  • │ label rate. Do not let mix sit overnight in the tank. │
  • │ 2. RINSE 1 — fill 10 percent of tank capacity with clean water, agitate, │
  • │ circulate through the boom and out every nozzle, then spray out. │
  • │ 3. CLEANING AGENT — add the agent the LABEL specifies (household ammonia, │
  • │ a commercial tank cleaner, or a detergent), fill, and CIRCULATE for the │
  • │ time the label states, often 15 minutes or more. Leave it in the boom. │
  • │ 4. RINSE 2 and RINSE 3 — clean water, circulate, spray out each time. │
  • │ 5. REMOVE AND CLEAN all screens, strainers, filters, nozzle tips and │
  • │ nozzle bodies BY HAND. Open the BOOM END CAPS and flush the ends. │
  • │ 6. DRY and store with tips off; leave the tank open to air where safe. │
  • └─────────────────────────────────────────────────────────────────────────────┘

Three rules govern the whole sequence:

Read the cleaning procedure on the label that was just applied , not on the one you are about to apply. The residue you are removing dictates the agent.

Volume beats time. Three small rinses remove far more residue than one large one, for exactly the same reason triple rinsing a container works better than a single fill.

Rinsate is a pesticide. Apply it to a site listed on the label at or below the labeled rate. It is not wash water, and it may not go to a storm drain, ditch, sanitary sewer, or bare ground near a wellhead.

Warning

Boom end caps are the most commonly skipped step. Sediment and concentrated residue collect in the last few inches of each boom section where flow is slowest. A cleanout that never opens the end caps leaves the worst contamination in place.

3. Filters, Screens, and Mesh

Screens protect the pump and the nozzle orifices, and they run coarse to fine in the direction of flow:

  • Position Typical mesh Purpose
  • Tank filler basket Coarsest Keeps debris out during filling
  • Suction (line) strainer , between tank and pump 16 to 50 mesh Protects the pump from abrasive particles
  • Pressure line strainer , after the pump 50 to 100 mesh Protects the boom
  • Nozzle screens 50 to 100 mesh Final protection for the orifice

Two operating rules: a higher mesh number means finer openings, and nozzle screen mesh must never be finer than the nozzle manufacturer specifies for that orifice — an over-fine screen plugs constantly and starves the tip. Wettable powders and dry flowables demand coarser screens than solutions because the suspended solids are the product.

4. Nozzle Wear and the 10 Percent Rule

Nozzle orifices erode. Abrasive suspensions (wettable powders, dry flowables), high pressure, and soft tip materials all accelerate it, and the failure is invisible — a worn tip sprays a wider, heavier stream that still looks correct.

The rule: replace any nozzle whose output exceeds 10 percent above the output of a new tip of the same size at the same pressure . Check tips by catching output from every nozzle for a fixed time and comparing.

  • Tip material Relative wear life Notes
  • Brass Shortest Cheap; wears fast, especially with abrasives; corrodes with fertilizer
  • Stainless steel Moderate to long Good general choice; hardened stainless better still
  • Polymer / plastic Moderate Inexpensive, corrosion resistant, can swell with some solvents
  • Ceramic Longest Highest initial cost, best resistance to abrasive suspensions

Never clean a tip with a knife, wire, or nail. Use a soft brush, compressed air, or water — enlarging the orifice by even a little permanently changes the output and the pattern.

5. Pumps, Seals, Hoses, and Tanks

  • Component Care
  • Roller pumps Simple and inexpensive; rollers wear with abrasive products. Check output against specification

Centrifugal pumps High volume, tolerant of abrasives, good for high-volume agitation; needs higher operating speed

Diaphragm and piston pumps Handle high pressure and abrasives well; inspect diaphragms for cracking

Hoses and gaskets Emulsifiable concentrate solvents swell and degrade rubber. Inspect for softening, cracking, and bulges; replace with material rated for the product

Tank Inspect for cracks, check that the lid gasket seals, verify the vent is clear, and confirm agitation actually moves the whole volume — a jet agitator aimed at one wall leaves dead zones where suspensions settle

Pressure gauge Verify against a known-good gauge annually; a drifting gauge invalidates every calibration made with it

Winterizing

Colorado sprayers freeze. Before storage: clean the system completely, drain all water, then circulate RV-type antifreeze through the pump, lines, and boom to protect seals and prevent freeze damage; remove and store nozzle tips and screens; grease fittings; store the tank open where possible and out of direct sunlight, which degrades polyethylene.

6. Where the Wash Water Goes

Equipment washing is the classic point source contamination event: a single location, repeated daily, with concentrated residue.

Wash on a designed mixing and loading pad with containment, or on a vegetated area well away from wells, ditches, and surface water , where the rinsate is applied at a rate no site receives repeatedly.

Colorado's mixing and loading guidance keeps these operations well back from wells, streams, and irrigation ditches unless performed over engineered containment.

Never wash equipment where the runoff can reach a storm drain, sanitary sewer, ditch, or well casing .

Recycle rinsate into the next compatible load whenever the label allows it. That converts a waste stream into product and eliminates the disposal question entirely.