Study guide
7.1 Cross-Connection Principles, Backsiphonage, and Backpressure
Colorado Journeyworker Plumber Journeyman Plumber
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Passing the Colorado Journeyworker Plumber Exam
1.1 Exam Blueprint, Format, and the 2024 Code Changeover 1.2 Colorado Licenses, Experience Hours, and Apprentice Supervision 1.3 Permits, Inspections, Blue Tags, and Board Enforcement
2 Chapter 2: General Regulations (IPC Chapter 3)
2.1 Approved Materials, Certification, and General Installation Rules 2.2 Protection of Pipes: Contact, Notching, Shield Plates, and Freezing 2.3 Piping Support, Trenching, Bedding, and Backfill 2.4 Required Tests: Water, Air, and Backflow Assembly Testing
3 Chapter 3: Fixtures and Equipment (IPC Chapter 4)
3.1 Minimum Fixture Counts, Separate Facilities, and Toilet Room Location 3.2 Fixture Clearances, Compartments, and Setting Requirements 3.3 Water Closets, Urinals, Lavatories, Sinks, and Flush Devices 3.4 Showers, Bathtubs, Fixture Fittings, and Scald Protection
4 Chapter 4: Water Heaters (IPC Chapter 5)
4.1 Water Heater Installation, Location, Access, and Clearances 4.2 Relief Valves and Discharge Piping 4.3 Water Heater Pans, Pan Drains, and Storage Tank Requirements 4.4 Thermal Expansion Control and Hot Water Temperature Limits
5 Chapter 5: Water Supply Materials and Installation (IPC Chapter 6)
5.1 Water Service and Distribution Materials, and Sewer Separation 5.2 Joints, Connections, and Dissimilar Materials in Water Piping 5.3 Valves, Shutoffs, and Required Valve Locations
6 Chapter 6: Water Supply Sizing and Pressure (IPC Chapter 6 and Appendix E)
6.1 Pressure Limits, Pressure Reducing Valves, and Water Hammer 6.2 Water Supply Fixture Units and Estimating Demand 6.3 Sizing Water Piping with Appendix E and Table E104.1
7 Chapter 7: Cross-Connection Control and Backflow Prevention (IPC Sections 608-610, Chapter 13)
7.1 Cross-Connection Principles, Backsiphonage, and Backpressure 7.2 Air Gaps and the Backflow Preventer Family 7.3 Applying Backflow Protection to Specific Connections 7.4 Nonpotable Water Systems, Identification, and Reclaimed Water
8 Chapter 8: Sanitary Drainage Materials and Fittings (IPC Chapter 7)
8.1 Sanitary Drainage Materials and Where Each May Be Used 8.2 Drainage Joints, Transitions, and Prohibited Connections 8.3 Fittings for Change of Direction and Drainage Flow Patterns
9 Chapter 9: Sanitary Drainage Sizing (IPC Sections 704, 709-711)
9.1 Drainage Fixture Units and Load Estimation 9.2 Slope of Horizontal Drainage and Installation Rules 9.3 Sizing Building Drains, Building Sewers, and Horizontal Branches 9.4 Stacks, Branch Intervals, and Offsets in Tall Buildings
10 Chapter 10: Cleanouts, Sumps and Below-Sewer Drainage (IPC Sections 708, 712-716)
10.1 Cleanouts, Manholes, and Access Requirements 10.2 Backwater Valves and Fixtures Below the Sewer Level 10.3 Sumps, Sewage Ejectors, and Macerating Toilet Systems 10.4 Building Sewers, Private Disposal, and Special Drainage Conditions
11 Chapter 11: Vent Fundamentals and Terminals (IPC Sections 901-905, 908)
11.1 How Vents Work, Trap Seal Loss, and the One-Inch Rule 11.2 Vent Terminals, Roof Penetrations, and Sidewall Terminations 11.3 Vent Connections, Grade, and the Six-Inch Rules
12 Chapter 12: Vent Types and Sizing (IPC Sections 906-911, 917)
12.1 Individual Vents, Common Vents, and Vents for Stack Offsets 12.2 Trap-to-Vent Distance, Trap Arms, and Fixture Drains 12.3 Sizing Stack Vents, Vent Stacks, Branch Vents, and Headers 12.4 Putting a Vent System Together: A Worked Building
13 Chapter 13: Engineered and Special Venting (IPC Sections 912-916, 918-920)
13.1 Horizontal and Vertical Wet Venting 13.2 Waste Stack Vents, Circuit Vents, and Combination Waste and Vent 13.3 Island Fixture Venting and Air Admittance Valves
14 Chapter 14: Traps, Interceptors and Separators (IPC Chapter 10)
14.1 Fixture Traps, Trap Seals, and Prohibited Trap Types 14.2 Trap Seal Protection, Primers, and Barrier Devices 14.3 Grease Interceptors, Oil Separators, and Solids Interceptors
15 Chapter 15: Indirect and Special Waste (IPC Chapter 8)
15.1 Where Indirect Waste Is Required, and Air Gap Versus Air Break 15.2 Waste Receptors, Hub Drains, and Standpipes 15.3 Special Wastes, Chemical Neutralization, and Health Care Drainage
16 Chapter 16: Storm Drainage (IPC Chapter 11 and Appendix B)
16.1 Storm Drainage Scope, Disposal, and Prohibited Connections 16.2 Storm Drainage Materials, Roof Drains, and Conductors 16.3 Secondary Roof Drains, Scuppers, and Controlled Flow Systems 16.4 Rainfall Rates, Roof Area, and the Flow-Rate Conversion 16.5 Sizing Vertical Conductors, Leaders, and Storm Drains 16.6 Gutters, Subsoil Drains, Building Subdrains, and Storm Sumps
17 Chapter 17: Residential Fire Sprinklers (IRC Section P2904)
17.1 Residential Fire Sprinkler Systems (IRC Section P2904)
18 Chapter 18: Isometric Analysis and Plumbing Calculations
18.1 Reading Plumbing Isometrics and Riser Diagrams 18.2 Analyzing a DWV Isometric for Code Compliance 18.3 Offsets, Travel, and the Plumbing Math the Exam Assumes
7.1 Cross-Connection Principles, Backsiphonage, and Backpressure
Key Takeaways Explain This Topic AI
IPC 608.7 prohibits cross connections except where approved backflow prevention assemblies, devices or other means are installed to protect the potable water supply.
IPC 608.7.1 prohibits cross connections between a private water supply and a potable public supply outright, with no protective device permitted.
Table 608.1 footnote a defines low hazard as pollution and high hazard as contamination, using the Section 202 definitions.
Backsiphonage results from negative or reduced pressure in the supply piping; backpressure results from downstream pressure exceeding the supply pressure.
IPC 608.6 prohibits introducing chemicals or substances that produce toxic conditions, taste, odor or discoloration into a potable water system.
Last updated: September 2026
What a cross connection is
The IPC defines a cross connection as any connection or arrangement, physical or otherwise, between a potable water supply system and any plumbing fixture, tank, receptacle, equipment or device through which nonpotable, used, unclean, polluted or contaminated water — or any substance — may enter or backflow into the potable system.
Two words in that definition do a lot of work: or otherwise . A cross connection does not require a permanently plumbed pipe. A garden hose lying in a swimming pool is a cross connection. A hose in a mop bucket of floor cleaner is a cross connection. A submerged inlet in a laundry tub is a cross connection.
IPC 608.1 sets the whole chapter's purpose:
A potable water supply system shall be designed, installed and maintained in such a manner so as to prevent contamination from nonpotable liquids, solids or gases being introduced into the potable water supply through cross connections or any other piping connections to the system. Backflow preventer applications shall conform to Table 608.1 , except as specifically stated in Sections 608.2 through 608.17.10.
IPC 608.7 states the rule: cross connections shall be prohibited , except where approved backflow prevention assemblies, devices or other means or methods are installed to protect the potable water supply.
IPC 608.7.1 carves out one case that admits no protective device: cross connections between a private water supply and a potable public supply shall be prohibited. A well may not be cross connected to the municipal supply even through an RPZ. The two systems must be physically separate.
The only two mechanisms
Backflow — the reversal of flow from its intended direction — happens by exactly two mechanisms, and choosing the right device depends entirely on which one can occur.
Backsiphonage
Cause: negative or reduced pressure in the supply piping pulls water backward, exactly as sucking on a straw does.
Real-world triggers:
A water main break downstream of the building.
Fire-fighting draw from a nearby hydrant collapsing local main pressure.
A booster pump running with inadequate suction pressure (which is why IPC 606.5.5 requires a low-pressure cutoff at 10 psi).
Shutting off the main while an elevated outlet is open, draining a high riser.
Undersized piping causing a high-velocity draw past a branch tee.
Backpressure
Cause: pressure downstream of the connection rises above the supply pressure and pushes the nonpotable fluid back into the potable system.
Real-world triggers:
A booster pump in a closed loop or process system.
A boiler whose operating pressure exceeds street pressure.
Elevated piping or tanks creating static head.
Thermal expansion in a closed heating system.
Compressed air or CO2 injected into a system, as in a carbonated beverage dispenser.
- Backsiphonage Backpressure
- Driving force Negative supply pressure Elevated downstream pressure
Typical cause Main break, hydrant draw, pump suction Pumps, boilers, elevation, thermal expansion, gas injection
Devices that handle it Air gap, RPZ, PVB, SVB, AVB, hose connection VB, barometric loop, double check Air gap, RPZ, double check, hose connection backflow preventer, dual check, ASSE 1012
Devices that cannot handle it — Any vacuum breaker — AVB, PVB, SVB, barometric loop
Memorize the negative rule : vacuum breakers of every type — atmospheric, pressure, spill-resistant — and the barometric loop are rated for backsiphonage only . If backpressure is possible, a vacuum breaker is the wrong device.
Degree of hazard
Table 608.1 sorts every device by degree of hazard , and footnote a ties the terms to the Section 202 definitions:
Low hazard = Pollution. An impairment of the quality of the potable water that does not create a hazard to health but does adversely and unreasonably affect the aesthetic qualities of the water for domestic use — taste, odor, color.
High hazard = Contamination. An impairment of the quality of the potable water that creates an actual hazard to the public health through poisoning or the spread of disease by sewage, industrial fluids or waste.
Examples:
- Situation Hazard Why
- Fire sprinkler system, no additives, potable water only Low Stagnant but not toxic
- Fire sprinkler system with antifreeze or chemical additives High Toxic additives
- Non-carbonated coffee machine Low Aesthetic only
- Carbonated beverage dispenser Low, but backpressure from CO2 Requires ASSE 1022
- Lawn irrigation, no chemical injection High Soil, fertilizer, animal waste in the piping
- Lawn irrigation with chemical injection High Requires RPZ
- Hospital fixtures, bedpan washers High Sewage contact
- Boiler with conditioning chemicals High Toxic treatment chemicals
- Heat exchanger with essentially toxic transfer fluid High Requires double-wall with a vented air gap
- Assemblies, devices and methods
Table 608.1 sorts protection into three categories, and the vocabulary matters:
Backflow prevention assemblies — testable, with shutoff valves and test cocks. Double check, double check detector fire protection, pressure vacuum breaker, reduced pressure principle, reduced pressure detector fire protection, spill-resistant vacuum breaker.
Backflow preventer plumbing devices — generally non-testable, built into or attached to equipment. Antisiphon fill valves, carbonated beverage machine preventers, ASSE 1012 intermediate atmospheric vent preventers, dual check valves, hose connection backflow preventers and vacuum breakers, laboratory faucet preventers, pipe-applied atmospheric vacuum breakers, vacuum breaker wall hydrants.
Other means or methods — air gap (ASME A112.1.2), air gap fittings (ASME A112.1.3), and the barometric loop .
An assembly can be field tested; a device usually cannot. That is why IPC 312.10.2 names assemblies plus hose connection backflow preventers for annual testing, and 312.10.1 requires annual inspection of all backflow prevention assemblies and air gaps .
Supporting prohibitions
Section Rule
608.2 Fixture supply lines and fittings installed to prevent backflow; fittings provide backflow protection per ASME A112.18.1
608.3 Devices for sterilization, distillation, processing, cooling, or storage of ice or foods must be protected
608.4 Pumps, filters, softeners and tanks handling potable water located to prevent contamination; their overflow, relief valve and waste discharge pipes terminate through an air gap
608.6 Chemicals producing toxic conditions, taste, odor or discoloration shall not be introduced into potable systems
608.10 Water used for cooling equipment or other processes shall not be returned to the potable system; it may be reused for flushing water closets and urinals or for irrigation, provided it is not sprayed onto areas open to public use
608.11 Piping that has conveyed nonpotable water or other contaminating substances shall not be reused for potable water
608.12 Potable water tanks must be enclosed and covered to prevent contamination, with vents and overflows protected
The Colorado enforcement layer
Cross-connection control is one of the Board's continuing education core competencies , and Colorado writes its own testing rule. Board Rule 1.2(E)(1)(q) replaces IPC 312.10.2 and requires the annual test to be performed by a certified cross-connection control technician — a person holding a valid Backflow Prevention Assembly Tester certification from ASSE, the American Backflow Prevention Association, or another Board-recognized agency (Rule 1.2(D)(8)(a)) — and adds the USC Foundation for Cross-Connection Control and Hydraulic Research 10th Edition Manual as an approved test procedure.
Colorado also draws a licensing line worth knowing: C.R.S. 12-155-118(4) exempts individuals who inspect, test or repair backflow prevention devices from plumbing licensure, but installation or removal of such devices is licensed plumbing work — except installing or replacing a device on a stand-alone fire suppression system . Board Rule 1.2(D)(10) repeats the point.
None of that is scored on the exam, which is based solely on the model 2021 IPC and IRC. It is, however, exactly the rule that governs your work the day after you pass.