Study guide
15.2 Waste Receptors, Hub Drains, and Standpipes
Colorado Journeyworker Plumber Journeyman Plumber
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Passing the Colorado Journeyworker Plumber Exam
1.1 Exam Blueprint, Format, and the 2024 Code Changeover 1.2 Colorado Licenses, Experience Hours, and Apprentice Supervision 1.3 Permits, Inspections, Blue Tags, and Board Enforcement
2 Chapter 2: General Regulations (IPC Chapter 3)
2.1 Approved Materials, Certification, and General Installation Rules 2.2 Protection of Pipes: Contact, Notching, Shield Plates, and Freezing 2.3 Piping Support, Trenching, Bedding, and Backfill 2.4 Required Tests: Water, Air, and Backflow Assembly Testing
3 Chapter 3: Fixtures and Equipment (IPC Chapter 4)
3.1 Minimum Fixture Counts, Separate Facilities, and Toilet Room Location 3.2 Fixture Clearances, Compartments, and Setting Requirements 3.3 Water Closets, Urinals, Lavatories, Sinks, and Flush Devices 3.4 Showers, Bathtubs, Fixture Fittings, and Scald Protection
4 Chapter 4: Water Heaters (IPC Chapter 5)
4.1 Water Heater Installation, Location, Access, and Clearances 4.2 Relief Valves and Discharge Piping 4.3 Water Heater Pans, Pan Drains, and Storage Tank Requirements 4.4 Thermal Expansion Control and Hot Water Temperature Limits
5 Chapter 5: Water Supply Materials and Installation (IPC Chapter 6)
5.1 Water Service and Distribution Materials, and Sewer Separation 5.2 Joints, Connections, and Dissimilar Materials in Water Piping 5.3 Valves, Shutoffs, and Required Valve Locations
6 Chapter 6: Water Supply Sizing and Pressure (IPC Chapter 6 and Appendix E)
6.1 Pressure Limits, Pressure Reducing Valves, and Water Hammer 6.2 Water Supply Fixture Units and Estimating Demand 6.3 Sizing Water Piping with Appendix E and Table E104.1
7 Chapter 7: Cross-Connection Control and Backflow Prevention (IPC Sections 608-610, Chapter 13)
7.1 Cross-Connection Principles, Backsiphonage, and Backpressure 7.2 Air Gaps and the Backflow Preventer Family 7.3 Applying Backflow Protection to Specific Connections 7.4 Nonpotable Water Systems, Identification, and Reclaimed Water
8 Chapter 8: Sanitary Drainage Materials and Fittings (IPC Chapter 7)
8.1 Sanitary Drainage Materials and Where Each May Be Used 8.2 Drainage Joints, Transitions, and Prohibited Connections 8.3 Fittings for Change of Direction and Drainage Flow Patterns
9 Chapter 9: Sanitary Drainage Sizing (IPC Sections 704, 709-711)
9.1 Drainage Fixture Units and Load Estimation 9.2 Slope of Horizontal Drainage and Installation Rules 9.3 Sizing Building Drains, Building Sewers, and Horizontal Branches 9.4 Stacks, Branch Intervals, and Offsets in Tall Buildings
10 Chapter 10: Cleanouts, Sumps and Below-Sewer Drainage (IPC Sections 708, 712-716)
10.1 Cleanouts, Manholes, and Access Requirements 10.2 Backwater Valves and Fixtures Below the Sewer Level 10.3 Sumps, Sewage Ejectors, and Macerating Toilet Systems 10.4 Building Sewers, Private Disposal, and Special Drainage Conditions
11 Chapter 11: Vent Fundamentals and Terminals (IPC Sections 901-905, 908)
11.1 How Vents Work, Trap Seal Loss, and the One-Inch Rule 11.2 Vent Terminals, Roof Penetrations, and Sidewall Terminations 11.3 Vent Connections, Grade, and the Six-Inch Rules
12 Chapter 12: Vent Types and Sizing (IPC Sections 906-911, 917)
12.1 Individual Vents, Common Vents, and Vents for Stack Offsets 12.2 Trap-to-Vent Distance, Trap Arms, and Fixture Drains 12.3 Sizing Stack Vents, Vent Stacks, Branch Vents, and Headers 12.4 Putting a Vent System Together: A Worked Building
13 Chapter 13: Engineered and Special Venting (IPC Sections 912-916, 918-920)
13.1 Horizontal and Vertical Wet Venting 13.2 Waste Stack Vents, Circuit Vents, and Combination Waste and Vent 13.3 Island Fixture Venting and Air Admittance Valves
14 Chapter 14: Traps, Interceptors and Separators (IPC Chapter 10)
14.1 Fixture Traps, Trap Seals, and Prohibited Trap Types 14.2 Trap Seal Protection, Primers, and Barrier Devices 14.3 Grease Interceptors, Oil Separators, and Solids Interceptors
15 Chapter 15: Indirect and Special Waste (IPC Chapter 8)
15.1 Where Indirect Waste Is Required, and Air Gap Versus Air Break 15.2 Waste Receptors, Hub Drains, and Standpipes 15.3 Special Wastes, Chemical Neutralization, and Health Care Drainage
16 Chapter 16: Storm Drainage (IPC Chapter 11 and Appendix B)
16.1 Storm Drainage Scope, Disposal, and Prohibited Connections 16.2 Storm Drainage Materials, Roof Drains, and Conductors 16.3 Secondary Roof Drains, Scuppers, and Controlled Flow Systems 16.4 Rainfall Rates, Roof Area, and the Flow-Rate Conversion 16.5 Sizing Vertical Conductors, Leaders, and Storm Drains 16.6 Gutters, Subsoil Drains, Building Subdrains, and Storm Sumps
17 Chapter 17: Residential Fire Sprinklers (IRC Section P2904)
17.1 Residential Fire Sprinkler Systems (IRC Section P2904)
18 Chapter 18: Isometric Analysis and Plumbing Calculations
18.1 Reading Plumbing Isometrics and Riser Diagrams 18.2 Analyzing a DWV Isometric for Code Compliance 18.3 Offsets, Travel, and the Plumbing Math the Exam Assumes
15.2 Waste Receptors, Hub Drains, and Standpipes
Key Takeaways Explain This Topic AI
IPC 802.4 requires a removable strainer or basket over the outlet of waste receptors, except for hub drains receiving only clear-water waste and standpipes.
IPC 802.4 prohibits waste receptors in concealed spaces, plenums, crawl spaces, attics, and interstitial spaces above ceilings and below floors, and requires ready access.
IPC 802.4.2 requires a hub drain to be in the form of a hub or a pipe extending not less than 1 inch above a water-impervious floor.
IPC 802.4.3 requires standpipes to be individually trapped and to extend not less than 18 inches but not greater than 42 inches above the trap weir, with access provided for rodding.
IPC 802.4.3.1 requires a laundry tray waste line connected to a standpipe to have the standpipe extend not less than 30 inches above the weir of the standpipe trap and above the flood level rim of the laundry tray.
Last updated: September 2026
What a waste receptor is
A waste receptor is the open fixture that catches indirect waste: a floor sink, a floor drain, a hub drain or a standpipe. IPC 802.3 requires it to be trapped and vented and connected to the building drainage system . The receptor is directly connected; the break is upstream of it.
The general rules — IPC 802.4
For other than hub drains that receive only clear-water waste and standpipes , a removable strainer or basket shall cover the outlet of waste receptors. Waste receptors shall not be installed in concealed spaces. Waste receptors shall not be installed in plenums, crawl spaces, attics, interstitial spaces above ceilings and below floors. Ready access shall be provided to waste receptors.
Four requirements:
Removable strainer or basket over the outlet — exempted only for hub drains receiving only clear-water waste and for standpipes .
Never in concealed spaces.
Never in plenums, crawl spaces, attics, or interstitial spaces above ceilings or below floors.
Ready access required.
The prohibition list is longer than the general "concealed" rule because each named space is a place where a receptor might be technically visible but practically unmaintainable — and where an overflow would be discovered only by the damage it caused.
802.4.1 Size of receptors : a waste receptor shall be sized for the maximum discharge of all indirect waste pipes served by the receptor , and installed to prevent splashing or flooding . Splash from a floor sink receiving a 15 gpm dish machine discharge contaminates the surrounding floor.
Colorado field note (not exam-scored): Board Rule 1.2(E)(1)(pp) adds an exception permitting a waste receptor in a crawl space where equipment is installed there, provided an approved backwater valve is installed. Rule 1.2(E)(1)(oo) deletes the last sentence of IPC 802.3.
Hub drains — IPC 802.4.2
A hub drain shall be in the form of a hub or a pipe extending not less than 1 inch above a water-impervious floor .
The 1-inch rise is what makes a hub drain a receptor rather than a hole in the floor: it keeps floor washdown water and debris from entering, and it gives the indirect waste pipe a flood level rim to measure the air gap from.
The strainer exemption applies only where the hub drain receives only clear-water waste . A hub drain receiving food-handling discharge needs a removable strainer like any other receptor.
Standpipes — IPC 802.4.3
Standpipes shall be individually trapped. Standpipes shall extend not less than 18 inches but not greater than 42 inches above the trap weir . Access shall be provided to standpipes and drains for rodding.
Three numbers, and both bounds are enforced:
- Requirement Value
- Minimum height above the trap weir 18 inches
- Maximum height above the trap weir 42 inches
- Trapping Individually trapped
Too short and the washing machine's pump surge overflows the top of the standpipe. Too tall and the head of water left standing in the standpipe after the pump stops can siphon the trap, or simply drains too slowly to keep up with the next discharge.
Relate this to IPC 1002.1 , which caps the vertical distance from a fixture outlet to the trap weir at 24 inches but expressly states that "the height of a clothes washer standpipe above a trap shall conform to Section 802.4.3." The standpipe rule supersedes the general 24-inch limit.
From Table 709.1 : a residential automatic clothes washer is 2 dfu with a 2-inch minimum trap; a commercial automatic clothes washer is 3 dfu with a 2-inch trap. Footnote g points to IPC 406.2 for sizing the fixture drain, branch drain and drainage stack for an automatic clothes washer standpipe.
802.4.3.1 Connection of a laundry tray to a standpipe
As an alternative for a laundry tray fixture connecting directly to a drainage system, a laundry tray waste line without a fixture trap shall connect to a standpipe for an automatic clothes washer drain . The standpipe shall extend not less than 30 inches above the weir of the standpipe trap and shall extend above the flood level rim of the laundry tray . The outlet of the laundry tray shall be not greater than 30 inches horizontal distance from the side of the standpipe .
Note the different minimum: a standpipe serving only a clothes washer is 18 inches minimum; a standpipe that also receives an untrapped laundry tray waste is 30 inches minimum, and must also rise above the laundry tray's flood level rim . The maximum remains 42 inches.
The laundry tray in this arrangement has no trap of its own — it is protected by the standpipe trap, which is why the standpipe must rise above the tray's rim.
Clothes washer discharge interceptor — IPC 1003.6
Clothes washers shall discharge through an interceptor provided with a wire basket or similar device, removable for cleaning , that prevents passage into the drainage system of solids 1/2 inch or larger in size, string, rags, buttons or other materials detrimental to the public sewage system.
Two exceptions:
Clothes washers in individual dwelling units.
A single clothes washer designed for use in individual dwelling units and installed in a location other than an individual dwelling unit — the residential-style washer in a small office break room.
So a commercial laundry needs the interceptor; a house does not; and a single residential machine in a non-dwelling location does not.
Sizing the receptor and its load
- Rule Requirement
- 802.4.1 Sized for the maximum discharge of all indirect waste pipes served ; prevent splashing or flooding
709.4 Receptor dfu = sum of the dfu of connected fixtures , but not less than the Table 709.1 or 709.2 value for the receptor
709.4.1 Receptors receiving only clear-water waste from display cases, refrigerated cases, ice bins, coolers and freezers = one-half dfu
- 709.3 Known flow converts at 1 gpm = 2 dfu
- Worked receptor load
A floor sink receives:
- two refrigerated display case drains (clear-water waste),
- one commercial dishwashing machine discharging 10 gpm , and
one prep sink at 2 dfu.
Because the receptor receives more than clear-water waste, 709.4.1's one-half dfu value does not apply . Use 709.4 — the sum of the connected fixtures:
Dishwasher: 10 gpm x 2 = 20 dfu (709.3).
Prep sink: 2 dfu .
Refrigerated case drains: clear water, but they are part of a mixed-waste receptor; count conservatively at the Table 709.1 floor drain value or the calculated clear-water flow.
Total: not less than 22 dfu , and never less than the Table 709.1 value for the receptor itself.
That load then flows into the drainage sizing tables of IPC 710.
Common receptor defects
- Defect Section
- Floor sink in a crawl space (model code) 802.4
- Floor sink above a ceiling in an interstitial space 802.4
- Receptor with no removable strainer receiving food waste 802.4
- Hub drain flush with the floor 802.4.2 (needs 1 inch above a water-impervious floor)
- Clothes washer standpipe 12 inches above the trap weir 802.4.3 (18 inches minimum)
- Clothes washer standpipe 54 inches above the trap weir 802.4.3 (42 inches maximum)
- Standpipe not individually trapped 802.4.3
- Untrapped laundry tray on a 20-inch standpipe 802.4.3.1 (30 inches minimum, above the tray rim)
- Indirect waste pipe extended into the receptor below the flood level rim where an air gap is required 802.3.1
- Receptor sized for one of three connected waste pipes 802.4.1