Study guide
17.1 Residential Fire Sprinkler Systems (IRC Section P2904)
Colorado Journeyworker Plumber Journeyman Plumber
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Passing the Colorado Journeyworker Plumber Exam
1.1 Exam Blueprint, Format, and the 2024 Code Changeover 1.2 Colorado Licenses, Experience Hours, and Apprentice Supervision 1.3 Permits, Inspections, Blue Tags, and Board Enforcement
2 Chapter 2: General Regulations (IPC Chapter 3)
2.1 Approved Materials, Certification, and General Installation Rules 2.2 Protection of Pipes: Contact, Notching, Shield Plates, and Freezing 2.3 Piping Support, Trenching, Bedding, and Backfill 2.4 Required Tests: Water, Air, and Backflow Assembly Testing
3 Chapter 3: Fixtures and Equipment (IPC Chapter 4)
3.1 Minimum Fixture Counts, Separate Facilities, and Toilet Room Location 3.2 Fixture Clearances, Compartments, and Setting Requirements 3.3 Water Closets, Urinals, Lavatories, Sinks, and Flush Devices 3.4 Showers, Bathtubs, Fixture Fittings, and Scald Protection
4 Chapter 4: Water Heaters (IPC Chapter 5)
4.1 Water Heater Installation, Location, Access, and Clearances 4.2 Relief Valves and Discharge Piping 4.3 Water Heater Pans, Pan Drains, and Storage Tank Requirements 4.4 Thermal Expansion Control and Hot Water Temperature Limits
5 Chapter 5: Water Supply Materials and Installation (IPC Chapter 6)
5.1 Water Service and Distribution Materials, and Sewer Separation 5.2 Joints, Connections, and Dissimilar Materials in Water Piping 5.3 Valves, Shutoffs, and Required Valve Locations
6 Chapter 6: Water Supply Sizing and Pressure (IPC Chapter 6 and Appendix E)
6.1 Pressure Limits, Pressure Reducing Valves, and Water Hammer 6.2 Water Supply Fixture Units and Estimating Demand 6.3 Sizing Water Piping with Appendix E and Table E104.1
7 Chapter 7: Cross-Connection Control and Backflow Prevention (IPC Sections 608-610, Chapter 13)
7.1 Cross-Connection Principles, Backsiphonage, and Backpressure 7.2 Air Gaps and the Backflow Preventer Family 7.3 Applying Backflow Protection to Specific Connections 7.4 Nonpotable Water Systems, Identification, and Reclaimed Water
8 Chapter 8: Sanitary Drainage Materials and Fittings (IPC Chapter 7)
8.1 Sanitary Drainage Materials and Where Each May Be Used 8.2 Drainage Joints, Transitions, and Prohibited Connections 8.3 Fittings for Change of Direction and Drainage Flow Patterns
9 Chapter 9: Sanitary Drainage Sizing (IPC Sections 704, 709-711)
9.1 Drainage Fixture Units and Load Estimation 9.2 Slope of Horizontal Drainage and Installation Rules 9.3 Sizing Building Drains, Building Sewers, and Horizontal Branches 9.4 Stacks, Branch Intervals, and Offsets in Tall Buildings
10 Chapter 10: Cleanouts, Sumps and Below-Sewer Drainage (IPC Sections 708, 712-716)
10.1 Cleanouts, Manholes, and Access Requirements 10.2 Backwater Valves and Fixtures Below the Sewer Level 10.3 Sumps, Sewage Ejectors, and Macerating Toilet Systems 10.4 Building Sewers, Private Disposal, and Special Drainage Conditions
11 Chapter 11: Vent Fundamentals and Terminals (IPC Sections 901-905, 908)
11.1 How Vents Work, Trap Seal Loss, and the One-Inch Rule 11.2 Vent Terminals, Roof Penetrations, and Sidewall Terminations 11.3 Vent Connections, Grade, and the Six-Inch Rules
12 Chapter 12: Vent Types and Sizing (IPC Sections 906-911, 917)
12.1 Individual Vents, Common Vents, and Vents for Stack Offsets 12.2 Trap-to-Vent Distance, Trap Arms, and Fixture Drains 12.3 Sizing Stack Vents, Vent Stacks, Branch Vents, and Headers 12.4 Putting a Vent System Together: A Worked Building
13 Chapter 13: Engineered and Special Venting (IPC Sections 912-916, 918-920)
13.1 Horizontal and Vertical Wet Venting 13.2 Waste Stack Vents, Circuit Vents, and Combination Waste and Vent 13.3 Island Fixture Venting and Air Admittance Valves
14 Chapter 14: Traps, Interceptors and Separators (IPC Chapter 10)
14.1 Fixture Traps, Trap Seals, and Prohibited Trap Types 14.2 Trap Seal Protection, Primers, and Barrier Devices 14.3 Grease Interceptors, Oil Separators, and Solids Interceptors
15 Chapter 15: Indirect and Special Waste (IPC Chapter 8)
15.1 Where Indirect Waste Is Required, and Air Gap Versus Air Break 15.2 Waste Receptors, Hub Drains, and Standpipes 15.3 Special Wastes, Chemical Neutralization, and Health Care Drainage
16 Chapter 16: Storm Drainage (IPC Chapter 11 and Appendix B)
16.1 Storm Drainage Scope, Disposal, and Prohibited Connections 16.2 Storm Drainage Materials, Roof Drains, and Conductors 16.3 Secondary Roof Drains, Scuppers, and Controlled Flow Systems 16.4 Rainfall Rates, Roof Area, and the Flow-Rate Conversion 16.5 Sizing Vertical Conductors, Leaders, and Storm Drains 16.6 Gutters, Subsoil Drains, Building Subdrains, and Storm Sumps
17 Chapter 17: Residential Fire Sprinklers (IRC Section P2904)
17.1 Residential Fire Sprinkler Systems (IRC Section P2904)
18 Chapter 18: Isometric Analysis and Plumbing Calculations
18.1 Reading Plumbing Isometrics and Riser Diagrams 18.2 Analyzing a DWV Isometric for Code Compliance 18.3 Offsets, Travel, and the Plumbing Math the Exam Assumes
17.1 Residential Fire Sprinkler Systems (IRC Section P2904)
Key Takeaways Explain This Topic AI
IRC P2904.1 treats Section P2904 as equivalent to NFPA 13D and applies it to stand-alone and multipurpose wet-pipe systems that do not use antifreeze.
IRC P2904.2.4.1 limits the area of coverage of a single sprinkler to not more than 400 square feet, based on the sprinkler listing and manufacturer's instructions.
IRC P2904.4.2 sets the design flow for a room with two or more sprinklers at the highest required single-sprinkler flow multiplied by 2.
IRC P2904.5.2 requires the water supply to sustain the design flow for 7 minutes for one-story dwellings under 2,000 square feet, and 10 minutes for dwellings two or more stories or 2,000 square feet and larger.
IRC P2904.6.1 requires a minimum pipe size of 3/4 inch nominal from the water supply source to any sprinkler, with threaded sprinkler adapter fittings not less than 1/2 inch nominal.
Last updated: September 2026
Why this is on a plumber's exam
C.R.S. 12-155-103(8)(a) includes in the definition of plumbing "all multipurpose residential fire sprinkler systems in one- and two-family dwellings and townhouses that are part of the potable water supply ." A multipurpose system is plumbing, installed by plumbers, inspected by plumbing inspectors. The PSI blueprint reflects that with 2 scored items on the Journeyworker exam and 4 items on the Residential Plumber and Master exams.
The governing text is IRC Section P2904 , part of IRC Chapter 29, which Colorado adopts through Board Rule 1.2(A)(2).
Two system types — IRC P2904.1
The design and installation of residential automatic sprinkler systems shall be in accordance with NFPA 13D or Section P2904 , which shall be considered to be equivalent to NFPA 13D . Partial residential sprinkler systems shall be permitted to be installed only in buildings not required to be equipped with a residential sprinkler system. Section P2904 shall apply to stand-alone and multipurpose wet-pipe sprinkler systems that do not include the use of antifreeze .
Type Definition
Multipurpose Provides domestic water to both fire sprinklers and plumbing fixtures — one piping system does both jobs
Stand-alone Separate and independent from the water distribution system
A backflow preventer shall not be required to separate a sprinkler system from the water distribution system, provided all four of the following are met:
The system complies with NFPA 13D or Section P2904 .
The piping material complies with Section P2906 .
The system does not contain antifreeze .
The system does not have a fire department connection .
That aligns with IPC 608.17.4 Exception 1 : where systems are installed as a portion of the water distribution system and are not provided with a fire department connection , isolation of the water supply system is not required. Add antifreeze or a fire department connection and backflow protection returns — IPC 608.17.4.1 then requires a reduced pressure principle assembly .
Where sprinklers are required — IRC P2904.1.1
Sprinklers shall be installed to protect all areas of a dwelling unit .
Four exceptions:
Attics, crawl spaces and normally unoccupied concealed spaces that do not contain fuel-fired appliances. Where such a space does contain fuel-fired equipment , a sprinkler shall be installed above the equipment , but sprinklers are not required in the remainder of the space.
Clothes closets, linen closets and pantries not exceeding 24 square feet in area, with the smallest dimension not greater than 3 feet , having wall and ceiling surfaces of gypsum board .
Bathrooms not more than 55 square feet in area.
Garages; carports; exterior porches; unheated entry areas, such as mud rooms, that are adjacent to an exterior door; and similar areas.
Three numbers to hold: 24 square feet and 3 feet for closets and pantries, and 55 square feet for bathrooms.
Sprinklers — IRC P2904.2
Sprinklers shall be new listed residential sprinklers and shall be installed in accordance with the sprinkler manufacturer's instructions .
New is literal. P2904.2.6 prohibits painting, caulking or modifying sprinklers, and requires sprinklers that have been painted, caulked, modified or damaged to be replaced with new sprinklers .
Temperature ratings — P2904.2.1 and P2904.2.2
- Condition Rating
- Ordinary Not less than 135 degrees F and not more than 225 degrees F
- Intermediate — required in the listed locations Not less than 175 degrees F and not more than 225 degrees F
Intermediate temperature sprinklers are required where installed:
Directly under skylights , where exposed to direct sunlight.
In attics.
In concealed spaces located directly beneath a roof.
Within the distance to a heat source specified in Table P2904.2.2.
Table P2904.2.2 ranges, measured in a straight line from the nearest edge of the heat source to the nearest edge of the sprinkler :
- Heat source Range requiring intermediate sprinklers
- Water heater, furnace or boiler 3 to 6 inches
- Luminaire up to 250 watts 3 to 6 inches
- Hot water pipe, not insulated 6 to 12 inches
- Luminaire 250 to 499 watts 6 to 12 inches
- Heating duct, not insulated 9 to 18 inches
- Kitchen range top 9 to 18 inches
- Oven 9 to 18 inches
- Vent connector or chimney connector 9 to 18 inches
- Coal and wood burning stove 12 to 42 inches
- Fireplace, side of open or recessed fireplace 12 to 36 inches
- Side of ceiling or wall warm-air register 12 to 24 inches
- Front of wall-mounted warm-air register 18 to 36 inches
- Fireplace, front of recessed fireplace 36 to 60 inches
Footnote a : sprinklers shall not be located at distances less than the minimum table distance unless the sprinkler listing allows a lesser distance. So the table does double duty: below the minimum, no sprinkler at all; within the range, an intermediate-temperature sprinkler; beyond the range, an ordinary sprinkler.
Freezing areas — P2904.2.3
Piping shall be protected from freezing as required by IRC P2603.5 , or by using:
A dry-pipe automatic sprinkler system listed for residential occupancy applications , or
Dry-sidewall or dry-pendent sprinklers extending from a nonfreezing area into a freezing area.
In Colorado, an unheated garage or an attic above an unconditioned space makes this a routine design question.
Coverage and obstructions — P2904.2.4
The area of coverage of a single sprinkler shall not exceed 400 square feet , and shall be based on the sprinkler listing and the sprinkler manufacturer's installation instructions .
P2904.2.4.2 Obstructions : sprinkler discharge shall not be blocked by obstructions unless additional sprinklers protect the obstructed area. No additional sprinklers are required where separation complies with Figure P2904.2.4.2 or the manufacturer's instructions where they permit a lesser distance.
Sprinkler type Considered obstructed within Section
Pendent 3 feet of the center of a ceiling fan, surface-mounted ceiling luminaire or similar object P2904.2.4.2.1
Sidewall 5 feet of the center of a ceiling fan, surface-mounted ceiling luminaire or similar object P2904.2.4.2.2
In both cases, additional sprinklers shall be installed .
P2904.2.5 : on systems assembled with solvent cement , the cementing of threaded adapter fittings shall be completed and the adapters verified as clear of excess cement before sprinklers are installed. Cement squeezed into a sprinkler orifice disables it silently.
Piping — IRC P2904.3
Sprinkler piping shall be supported in accordance with requirements for cold water distribution piping and shall comply with the requirements for cold water distribution piping . For multipurpose piping systems, the sprinkler piping shall connect to and be a part of the cold water distribution piping system .
P2904.3.1 : nonmetallic pipe and tubing such as CPVC, PEX and PE-RT shall be listed for use in residential fire sprinkler systems — ordinary potable-rated CPVC is not automatically acceptable.
P2904.3.1.1 Nonmetallic pipe protection : nonmetallic systems shall be protected from exposure to the living space by not less than 3/8-inch gypsum wallboard, 1/2-inch plywood, or other material having a 15-minute fire rating . Two exceptions: areas that do not require sprinkler protection under P2904.1.1, and where exposed piping is permitted by the pipe listing .
P2904.3.2 Shutoff valves prohibited :
With the exception of shutoff valves for the entire water distribution system or a single master control valve for the automatic sprinkler system that is locked in the open position , valves shall not be installed in any location where the valve would isolate piping serving one or more sprinklers.
This is the rule that most often collides with plumbing habit. You may not put a stop on a branch that also feeds a sprinkler.
P2904.3.3 Single dwelling limit : piping beyond the service valve at the beginning of the water distribution system shall not serve more than one dwelling .
P2904.3.4 Drain : a means to drain the sprinkler system shall be provided on the system side of the water distribution shutoff valve .
Determining design flow — IRC P2904.4
P2904.4.1 : the minimum required flow for each sprinkler comes from the manufacturer's published data for the specific model, based on the area of coverage , the ceiling configuration , the temperature rating , and any additional manufacturer conditions.
P2904.4.2 System design flow rate :
A room with one sprinkler : the flow required for that sprinkler .
A room with two or more sprinklers : the highest required flow rate in that room multiplied by 2 .
Where the manufacturer specifies different criteria for non-smooth, non-flat or non-horizontal ceilings, follow the manufacturer's instructions .
The design flow rate for the system is the flow required by the room with the largest flow rate.
It is permissible to reduce the design flow by subdividing a space into two or more rooms , each bounded by walls and a ceiling , where openings in walls have a lintel not less than 8 inches in depth forming a solid barrier between the ceiling and the top of the opening.
Two sprinklers, never more. No matter how many sprinklers a room contains, the design case is two operating , and the number used is twice the single highest flow .
Worked design flow
A house has a great room with five sprinklers (highest published flow 16 gpm ), a bedroom with one sprinkler ( 13 gpm ) and a kitchen with two sprinklers (highest 14 gpm ).
- Room Sprinklers Design flow
- Great room 5 16 x 2 = 32 gpm
- Kitchen 2 14 x 2 = 28 gpm
- Bedroom 1 13 gpm
System design flow = 32 gpm , the largest room requirement.
Water supply — IRC P2904.5
The water supply shall provide not less than the required design flow rate at a pressure not less than that used to comply with Section P2904.6 .
P2904.5.1 : where the supply is from a tank system, a private well system or a combination , the available supply is based on the minimum pressure control setting for the pump .
P2904.5.2 Required capacity — the duration the supply must sustain the design flow:
- Dwelling Duration
- One story in height and less than 2,000 square feet 7 minutes
- Two or more stories , or 2,000 square feet or greater 10 minutes
Where a well, a tank or a combination is used, any combination of well capacity and tank storage may meet the requirement.
Worked storage
The 32 gpm system above serves a two-story house on a well.
Required duration: 10 minutes (two or more stories).
Required volume: 32 gpm x 10 min = 320 gallons available at the design flow and pressure.
Had the house been one story at 1,800 square feet : 32 x 7 = 224 gallons .
Pipe sizing — IRC P2904.6
The piping to sprinklers shall be sized for the flow required by P2904.4.2 . The flow required to supply the plumbing fixtures shall not be required to be added to the sprinkler design flow.
That sentence matters in a multipurpose system: you do not add domestic demand to sprinkler demand. The design case is a fire, during which fixture use is not assumed.
P2904.6.1 Method of sizing :
The prescriptive method in P2904.6.2, or hydraulic calculation per NFPA 13D .
Minimum pipe size from the water supply source to any sprinkler: 3/4 inch nominal.
Threaded adapter fittings where sprinklers attach: not less than 1/2 inch nominal.
P2904.6.2 sizes pipe by determining the available pressure to offset friction loss , using tabulated losses:
Table Loss
P2904.6.2(1) Water service pressure loss by flow rate, service size (3/4, 1, 1-1/4 inch) and length (40 ft or less, 41-75, 76-100, 101-150). Values assume SDR 11 and a Hazen Williams C factor of 150, and include a 25 percent length allowance for fittings up to 100 feet and 15 percent over 100 feet
P2904.6.2(2) Minimum water meter pressure loss by flow rate and meter size (5/8, 3/4, 1 inch); where the actual published loss is available from the meter manufacturer, use that value instead
P2904.6.2(3) Elevation loss — approximately 0.434 psi per foot of rise (4.4 psi at 10 feet)
Both service and meter tables carry the same footnote: add 5 gpm to the flow rate required by P2904.4.2 where the water service pipe supplies more than one dwelling.
Colorado context
Point Rule
Multipurpose residential sprinklers in 1- and 2-family dwellings and townhouses that are part of the potable water supply are plumbing C.R.S. 12-155-103(8)(a)
Fire protection systems other than those multipurpose systems are not plumbing C.R.S. 12-155-118(6)(a)(I)
Installing or replacing a backflow preventer on a stand-alone fire suppression system does not require a plumbing license C.R.S. 12-155-118(4)