Study guide
9.2 Slope of Horizontal Drainage and Installation Rules
Colorado Journeyworker Plumber Journeyman Plumber
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Passing the Colorado Journeyworker Plumber Exam
1.1 Exam Blueprint, Format, and the 2024 Code Changeover 1.2 Colorado Licenses, Experience Hours, and Apprentice Supervision 1.3 Permits, Inspections, Blue Tags, and Board Enforcement
2 Chapter 2: General Regulations (IPC Chapter 3)
2.1 Approved Materials, Certification, and General Installation Rules 2.2 Protection of Pipes: Contact, Notching, Shield Plates, and Freezing 2.3 Piping Support, Trenching, Bedding, and Backfill 2.4 Required Tests: Water, Air, and Backflow Assembly Testing
3 Chapter 3: Fixtures and Equipment (IPC Chapter 4)
3.1 Minimum Fixture Counts, Separate Facilities, and Toilet Room Location 3.2 Fixture Clearances, Compartments, and Setting Requirements 3.3 Water Closets, Urinals, Lavatories, Sinks, and Flush Devices 3.4 Showers, Bathtubs, Fixture Fittings, and Scald Protection
4 Chapter 4: Water Heaters (IPC Chapter 5)
4.1 Water Heater Installation, Location, Access, and Clearances 4.2 Relief Valves and Discharge Piping 4.3 Water Heater Pans, Pan Drains, and Storage Tank Requirements 4.4 Thermal Expansion Control and Hot Water Temperature Limits
5 Chapter 5: Water Supply Materials and Installation (IPC Chapter 6)
5.1 Water Service and Distribution Materials, and Sewer Separation 5.2 Joints, Connections, and Dissimilar Materials in Water Piping 5.3 Valves, Shutoffs, and Required Valve Locations
6 Chapter 6: Water Supply Sizing and Pressure (IPC Chapter 6 and Appendix E)
6.1 Pressure Limits, Pressure Reducing Valves, and Water Hammer 6.2 Water Supply Fixture Units and Estimating Demand 6.3 Sizing Water Piping with Appendix E and Table E104.1
7 Chapter 7: Cross-Connection Control and Backflow Prevention (IPC Sections 608-610, Chapter 13)
7.1 Cross-Connection Principles, Backsiphonage, and Backpressure 7.2 Air Gaps and the Backflow Preventer Family 7.3 Applying Backflow Protection to Specific Connections 7.4 Nonpotable Water Systems, Identification, and Reclaimed Water
8 Chapter 8: Sanitary Drainage Materials and Fittings (IPC Chapter 7)
8.1 Sanitary Drainage Materials and Where Each May Be Used 8.2 Drainage Joints, Transitions, and Prohibited Connections 8.3 Fittings for Change of Direction and Drainage Flow Patterns
9 Chapter 9: Sanitary Drainage Sizing (IPC Sections 704, 709-711)
9.1 Drainage Fixture Units and Load Estimation 9.2 Slope of Horizontal Drainage and Installation Rules 9.3 Sizing Building Drains, Building Sewers, and Horizontal Branches 9.4 Stacks, Branch Intervals, and Offsets in Tall Buildings
10 Chapter 10: Cleanouts, Sumps and Below-Sewer Drainage (IPC Sections 708, 712-716)
10.1 Cleanouts, Manholes, and Access Requirements 10.2 Backwater Valves and Fixtures Below the Sewer Level 10.3 Sumps, Sewage Ejectors, and Macerating Toilet Systems 10.4 Building Sewers, Private Disposal, and Special Drainage Conditions
11 Chapter 11: Vent Fundamentals and Terminals (IPC Sections 901-905, 908)
11.1 How Vents Work, Trap Seal Loss, and the One-Inch Rule 11.2 Vent Terminals, Roof Penetrations, and Sidewall Terminations 11.3 Vent Connections, Grade, and the Six-Inch Rules
12 Chapter 12: Vent Types and Sizing (IPC Sections 906-911, 917)
12.1 Individual Vents, Common Vents, and Vents for Stack Offsets 12.2 Trap-to-Vent Distance, Trap Arms, and Fixture Drains 12.3 Sizing Stack Vents, Vent Stacks, Branch Vents, and Headers 12.4 Putting a Vent System Together: A Worked Building
13 Chapter 13: Engineered and Special Venting (IPC Sections 912-916, 918-920)
13.1 Horizontal and Vertical Wet Venting 13.2 Waste Stack Vents, Circuit Vents, and Combination Waste and Vent 13.3 Island Fixture Venting and Air Admittance Valves
14 Chapter 14: Traps, Interceptors and Separators (IPC Chapter 10)
14.1 Fixture Traps, Trap Seals, and Prohibited Trap Types 14.2 Trap Seal Protection, Primers, and Barrier Devices 14.3 Grease Interceptors, Oil Separators, and Solids Interceptors
15 Chapter 15: Indirect and Special Waste (IPC Chapter 8)
15.1 Where Indirect Waste Is Required, and Air Gap Versus Air Break 15.2 Waste Receptors, Hub Drains, and Standpipes 15.3 Special Wastes, Chemical Neutralization, and Health Care Drainage
16 Chapter 16: Storm Drainage (IPC Chapter 11 and Appendix B)
16.1 Storm Drainage Scope, Disposal, and Prohibited Connections 16.2 Storm Drainage Materials, Roof Drains, and Conductors 16.3 Secondary Roof Drains, Scuppers, and Controlled Flow Systems 16.4 Rainfall Rates, Roof Area, and the Flow-Rate Conversion 16.5 Sizing Vertical Conductors, Leaders, and Storm Drains 16.6 Gutters, Subsoil Drains, Building Subdrains, and Storm Sumps
17 Chapter 17: Residential Fire Sprinklers (IRC Section P2904)
17.1 Residential Fire Sprinkler Systems (IRC Section P2904)
18 Chapter 18: Isometric Analysis and Plumbing Calculations
18.1 Reading Plumbing Isometrics and Riser Diagrams 18.2 Analyzing a DWV Isometric for Code Compliance 18.3 Offsets, Travel, and the Plumbing Math the Exam Assumes
9.2 Slope of Horizontal Drainage and Installation Rules
Key Takeaways Explain This Topic AI
IPC Table 704.1 requires a minimum slope of 1/4 inch per foot for horizontal drainage pipe 2-1/2 inches or less in size.
IPC Table 704.1 requires a minimum slope of 1/8 inch per foot for horizontal drainage pipe 3 inches through 6 inches, and 1/16 inch per foot for pipe 8 inches or larger.
IPC 704.1 requires piping upstream of a grease interceptor to slope not less than 1/4 inch per foot regardless of pipe size.
IPC 704.2 prohibits reducing the size of drainage piping in the direction of flow, excepting only three water closet connection arrangements.
A slope of 1/4 inch per foot is a 2 percent slope, 1/8 inch per foot is 1 percent, and 1/16 inch per foot is 0.5 percent.
Last updated: September 2026
Why slope is a band, not a minimum only
Drainage is a two-phase flow: liquid carrying solids, with an air core above. Too little slope and the liquid stalls, depositing solids. Too much slope and the liquid outruns the solids, leaving them stranded — the classic "the pipe is too steep" failure on a short, steep run from a water closet.
The code publishes minimums . Good practice adds a working maximum for the same reason.
Table 704.1 — minimum slope of horizontal drainage pipe
- Pipe size Minimum slope (inch per foot) Percent Drop per 10 feet
- 2-1/2 inches or less 1/4 2% 2-1/2 inches
- 3 to 6 inches 1/8 1% 1-1/4 inches
- 8 inches or larger 1/16 0.5% 5/8 inch
Read the size breaks carefully. The first row stops at 2-1/2 inches , not 2 inches. The second row begins at 3 inches , not 4. Those two boundaries are the most common transcription error candidates carry into the exam room.
The grease interceptor override
IPC 704.1 adds one exception in the body text:
...except that where the drainage piping is upstream of a grease interceptor , the slope of the piping shall be not less than 1/4 inch per foot (2-percent slope) .
That applies regardless of pipe size . A 4-inch line feeding a grease interceptor gets 1/4 inch per foot , not the 1/8 inch per foot its size would otherwise allow. Grease congeals on a cold pipe wall, and the higher velocity of a steeper line keeps it moving.
Table 704.1 footnote a points at the same rule from the table side.
Uniform alignment, uniform slope
IPC 704.1 opens with a requirement that inspectors cite constantly:
Horizontal drainage piping shall be installed in uniform alignment at uniform slopes .
A run that sags between hangers creates a belly — a low point that holds standing water, collects solids and eventually blocks. The remedy is Chapter 3 discipline: hanger spacing per Table 308.5 (4 feet for PVC and ABS, 5 feet for cast iron, 10 feet for cast iron in 10-foot lengths), continuous support for buried piping under 306.1 , and bedding that does not settle under 306.2 .
No reduction in the direction of flow — IPC 704.2
The size of the drainage piping shall not be reduced in the direction of the flow.
Three arrangements are not considered reductions:
A 4-inch by 3-inch water closet flange .
A water closet bend fitting with a 4-inch inlet and a 3-inch outlet , provided the 4-inch leg of the fitting is upright and below , but not necessarily directly connected to, the water closet flange.
An offset closet flange .
The same rule appears on the storm side at IPC 1101.5 .
Connections to offsets and bases of stacks — IPC 704.3
Horizontal branches connect to the base of a stack, or to a horizontal stack offset, not less than 10 times the diameter of the stack downstream . A 3-inch stack requires 30 inches, a 4-inch stack 40 inches, a 6-inch stack 60 inches.
- Working the arithmetic
- Converting between slope expressions
- Expression Equivalent
- 1/4 inch per foot 2 percent
- 1/8 inch per foot 1 percent
- 1/16 inch per foot 0.5 percent
- 1/2 inch per foot 4 percent
Percent slope = (inches of fall per foot) / 12 x 100. Check: (0.25 / 12) x 100 = 2.08, conventionally stated as 2 percent.
- Total fall over a run
- Fall = slope (in/ft) x run (ft)
A 4-inch building drain runs 64 feet from the last fixture connection to the foundation wall.
Minimum slope for 4-inch pipe: 1/8 inch per foot .
Fall = 0.125 x 64 = 8 inches .
If the invert at the fixture end must be 18 inches below the slab, the invert at the wall is 26 inches below the slab.
Invert elevation at a point
A 3-inch branch starts at invert elevation 100.00 feet and runs 38 feet at the minimum slope.
Fall = 0.125 in/ft x 38 ft = 4.75 inches = 0.396 feet .
Invert at the far end = 100.00 - 0.396 = 99.60 feet .
Available fall constrains pipe size
A building sewer must travel 110 feet from the building to a main whose invert is 13 inches lower than the building drain outlet.
Available slope = 13 inches / 110 feet = 0.118 inch per foot .
That is less than 1/8 inch per foot (0.125) , so a 4-inch or 6-inch sewer at minimum slope will not fit the available fall.
Options: increase the pipe to 8 inches , whose minimum is 1/16 inch per foot (0.0625) — 110 x 0.0625 = 6.9 inches of required fall, easily within the 13 inches available; or lower the connection; or install a pump.
This is exactly the trade-off Table 710.1(1) reflects: bigger pipe, flatter slope, but less capacity per inch of diameter at that flatter slope.
Slope and capacity interact
Table 710.1(1) publishes a different capacity for each slope. For a 4-inch building drain:
- Slope Maximum dfu
- 1/8 inch per foot 180
- 1/4 inch per foot 216
- 1/2 inch per foot 250
Doubling the slope from 1/8 to 1/4 buys 20 percent more capacity. That is why a designer short on pipe size will sometimes buy capacity with slope instead — and why "minimum slope" and "design slope" are not the same number.
Note also that the 1/16 inch per foot column is blank for pipes smaller than 8 inches , because Table 704.1 does not permit that slope below 8 inches.
Computerized design does not escape the table
IPC 713.3.2 : where the drainage system is designed by approved computer methods, horizontal drainage piping shall still be designed and installed at slopes in accordance with Table 704.1 . The software may size the pipe; it may not flatten it below the code minimum.