Study guide

11.2 Vent Terminals, Roof Penetrations, and Sidewall Terminations

Colorado Journeyworker Plumber Journeyman Plumber

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Passing the Colorado Journeyworker Plumber Exam

1.1 Exam Blueprint, Format, and the 2024 Code Changeover 1.2 Colorado Licenses, Experience Hours, and Apprentice Supervision 1.3 Permits, Inspections, Blue Tags, and Board Enforcement

2 Chapter 2: General Regulations (IPC Chapter 3)

2.1 Approved Materials, Certification, and General Installation Rules 2.2 Protection of Pipes: Contact, Notching, Shield Plates, and Freezing 2.3 Piping Support, Trenching, Bedding, and Backfill 2.4 Required Tests: Water, Air, and Backflow Assembly Testing

3 Chapter 3: Fixtures and Equipment (IPC Chapter 4)

3.1 Minimum Fixture Counts, Separate Facilities, and Toilet Room Location 3.2 Fixture Clearances, Compartments, and Setting Requirements 3.3 Water Closets, Urinals, Lavatories, Sinks, and Flush Devices 3.4 Showers, Bathtubs, Fixture Fittings, and Scald Protection

4 Chapter 4: Water Heaters (IPC Chapter 5)

4.1 Water Heater Installation, Location, Access, and Clearances 4.2 Relief Valves and Discharge Piping 4.3 Water Heater Pans, Pan Drains, and Storage Tank Requirements 4.4 Thermal Expansion Control and Hot Water Temperature Limits

5 Chapter 5: Water Supply Materials and Installation (IPC Chapter 6)

5.1 Water Service and Distribution Materials, and Sewer Separation 5.2 Joints, Connections, and Dissimilar Materials in Water Piping 5.3 Valves, Shutoffs, and Required Valve Locations

6 Chapter 6: Water Supply Sizing and Pressure (IPC Chapter 6 and Appendix E)

6.1 Pressure Limits, Pressure Reducing Valves, and Water Hammer 6.2 Water Supply Fixture Units and Estimating Demand 6.3 Sizing Water Piping with Appendix E and Table E104.1

7 Chapter 7: Cross-Connection Control and Backflow Prevention (IPC Sections 608-610, Chapter 13)

7.1 Cross-Connection Principles, Backsiphonage, and Backpressure 7.2 Air Gaps and the Backflow Preventer Family 7.3 Applying Backflow Protection to Specific Connections 7.4 Nonpotable Water Systems, Identification, and Reclaimed Water

8 Chapter 8: Sanitary Drainage Materials and Fittings (IPC Chapter 7)

8.1 Sanitary Drainage Materials and Where Each May Be Used 8.2 Drainage Joints, Transitions, and Prohibited Connections 8.3 Fittings for Change of Direction and Drainage Flow Patterns

9 Chapter 9: Sanitary Drainage Sizing (IPC Sections 704, 709-711)

9.1 Drainage Fixture Units and Load Estimation 9.2 Slope of Horizontal Drainage and Installation Rules 9.3 Sizing Building Drains, Building Sewers, and Horizontal Branches 9.4 Stacks, Branch Intervals, and Offsets in Tall Buildings

10 Chapter 10: Cleanouts, Sumps and Below-Sewer Drainage (IPC Sections 708, 712-716)

10.1 Cleanouts, Manholes, and Access Requirements 10.2 Backwater Valves and Fixtures Below the Sewer Level 10.3 Sumps, Sewage Ejectors, and Macerating Toilet Systems 10.4 Building Sewers, Private Disposal, and Special Drainage Conditions

11 Chapter 11: Vent Fundamentals and Terminals (IPC Sections 901-905, 908)

11.1 How Vents Work, Trap Seal Loss, and the One-Inch Rule 11.2 Vent Terminals, Roof Penetrations, and Sidewall Terminations 11.3 Vent Connections, Grade, and the Six-Inch Rules

12 Chapter 12: Vent Types and Sizing (IPC Sections 906-911, 917)

12.1 Individual Vents, Common Vents, and Vents for Stack Offsets 12.2 Trap-to-Vent Distance, Trap Arms, and Fixture Drains 12.3 Sizing Stack Vents, Vent Stacks, Branch Vents, and Headers 12.4 Putting a Vent System Together: A Worked Building

13 Chapter 13: Engineered and Special Venting (IPC Sections 912-916, 918-920)

13.1 Horizontal and Vertical Wet Venting 13.2 Waste Stack Vents, Circuit Vents, and Combination Waste and Vent 13.3 Island Fixture Venting and Air Admittance Valves

14 Chapter 14: Traps, Interceptors and Separators (IPC Chapter 10)

14.1 Fixture Traps, Trap Seals, and Prohibited Trap Types 14.2 Trap Seal Protection, Primers, and Barrier Devices 14.3 Grease Interceptors, Oil Separators, and Solids Interceptors

15 Chapter 15: Indirect and Special Waste (IPC Chapter 8)

15.1 Where Indirect Waste Is Required, and Air Gap Versus Air Break 15.2 Waste Receptors, Hub Drains, and Standpipes 15.3 Special Wastes, Chemical Neutralization, and Health Care Drainage

16 Chapter 16: Storm Drainage (IPC Chapter 11 and Appendix B)

16.1 Storm Drainage Scope, Disposal, and Prohibited Connections 16.2 Storm Drainage Materials, Roof Drains, and Conductors 16.3 Secondary Roof Drains, Scuppers, and Controlled Flow Systems 16.4 Rainfall Rates, Roof Area, and the Flow-Rate Conversion 16.5 Sizing Vertical Conductors, Leaders, and Storm Drains 16.6 Gutters, Subsoil Drains, Building Subdrains, and Storm Sumps

17 Chapter 17: Residential Fire Sprinklers (IRC Section P2904)

17.1 Residential Fire Sprinkler Systems (IRC Section P2904)

18 Chapter 18: Isometric Analysis and Plumbing Calculations

18.1 Reading Plumbing Isometrics and Riser Diagrams 18.2 Analyzing a DWV Isometric for Code Compliance 18.3 Offsets, Travel, and the Plumbing Math the Exam Assumes

11.2 Vent Terminals, Roof Penetrations, and Sidewall Terminations

Key Takeaways Explain This Topic AI

IPC 903.1.2 requires open vent pipes to terminate not less than 7 feet above a roof used as a promenade, restaurant, bar, sunbathing deck or observation deck.

IPC 903.1.3 permits a vent covered by a roof-mounted panel or architectural element to terminate not less than 2 inches above the roof surface, with an open area not less than the pipe area and bird and rodent protection.

IPC 903.1.4 requires sidewall vent terminals to be not less than 10 feet from the lot line and 10 feet above the highest adjacent grade within 10 feet horizontally.

IPC 903.2 requires vent extensions through a roof or wall to be not less than 3 inches in diameter where the 97.5 percent outdoor design temperature is 0 degrees F or less, with the increase made at least 1 foot inside the thermal envelope.

IPC 903.5 prohibits an open vent terminal directly beneath a door, openable window or air intake, and within 10 feet horizontally unless it is 3 feet or more above the top of the opening.

Last updated: September 2026

The terminal is the system's only opening

IPC 903.1 : the vent pipe shall terminate by extending to the outdoors through the roof or the side wall by one of the four methods in 903.1.1 through 903.1.4. Everything the vent system does depends on that opening staying open, unobstructed, and away from places where sewer gas can re-enter the building.

  • Roof terminations
  • 903.1.1 Roof extension unprotected

Open vent pipes that extend through a roof shall be terminated not less than [NUMBER] inches above the roof .

The number is bracketed in the model code, meaning the adopting jurisdiction fills it in. The exam is based on the model 2021 IPC, so an item asking for a specific unprotected-roof height would have to supply the jurisdiction's number.

Colorado field note (not exam-scored): Board Rule 1.2(E)(1)(qq) fills the bracket with 6 inches : "All open vent pipes that extend through a roof shall be terminated at least 6 inches above the roof."

903.1.2 Roof used for recreational or assembly purposes

Where a roof is to be used as a promenade, restaurant, bar, or sunbathing deck, as an observation deck, or for similar purposes , open vent pipes shall terminate not less than 7 feet above the roof .

Seven feet puts the opening above the breathing zone of people standing on the deck.

903.1.3 Protected vent terminal

Where a vent terminates above a sloped roof and is covered by either a roof-mounted panel (a solar collector or photovoltaic panel mounted over the vent opening) or a roof element (an architectural feature or decorative shroud), the vent pipe shall terminate not less than 2 inches above the roof surface . Four conditions attach:

Roof elements must be designed to prevent the adverse effects of snow accumulation and wind on the vent's function.

The panel placement or roof element design must provide an open area to the outdoors not less than the area of the pipe , calculated from the inside diameter .

The terminal must be protected by a method that prevents birds and rodents from entering or blocking the opening.

The roof must be sloped .

Colorado field note (not exam-scored): Board Rule 1.2(E)(1)(rr) changes 2 inches to 4 inches for the protected vent terminal in Colorado.

903.1.4 Sidewall vent terminal

  • Requirement Value
  • Distance from the lot line not less than 10 feet
  • Height above the highest adjacent grade within 10 feet horizontally not less than 10 feet
  • Under an overhang with soffit vents Prohibited
  • Bird and rodent protection Required

Both 10-foot dimensions must be satisfied, and the soffit prohibition exists because a soffit vent pulls air directly into the attic and then into the building.

Frost closure — IPC 903.2

Where the 97.5-percent value for outdoor design temperature is 0 degrees F or less , vent extensions through a roof or wall shall be not less than 3 inches in diameter . Any increase in the size of the vent shall be made not less than 1 foot inside the thermal envelope of the building .

The physics: warm, saturated sewer gas rising through a cold vent deposits frost on the inside wall of the pipe. On a 2-inch pipe in sustained sub-zero weather the frost ring can close the opening entirely in a day. A 3-inch opening takes far longer to close, and making the transition 1 foot inside the thermal envelope puts the enlargement where the pipe is still warm, so the joint itself does not become the frost point.

IPC 903.6 Extension outside a structure : where the 97.5-percent outdoor design temperature is less than 0 degrees F , vent pipes installed on the exterior of the structure shall be protected against freezing by insulation, heat or both .

Colorado field note — an important divergence: Board Rule 1.2(E)(1)(ss) deletes IPC 903.2 Frost Closure in its entirety from the Colorado Plumbing Code. Colorado, a state with many jurisdictions well below a 0-degree design temperature, does not require the 3-inch vent extension. Board Rule 1.2(E)(2)(xx) does the same for IRC Section P3103.2.

On the exam, the model-code answer is the 3-inch rule. In a Colorado installation, the rule does not apply. This is one of the clearest cases where the exam answer and the field answer differ, and the PSI bulletin tells you which to use: the test is based solely on the model 2021 IPC and IRC.

Location of the terminal — IPC 903.5

An open vent terminal from a drainage system shall not be located directly beneath any door, openable window, or other air intake opening of the building or of an adjacent building, and any such vent terminal shall not be within 10 feet horizontally of such an opening unless it is 3 feet or more above the top of such opening .

Three tests, applied in order:

Directly beneath an opening? Never permitted , at any height.

Within 10 feet horizontally of an opening? Permitted only if the terminal is 3 feet or more above the top of the opening .

More than 10 feet horizontally away? Permitted.

The rule protects adjacent buildings as well as the one being vented. A sidewall vent 6 feet from a neighbor's bedroom window is a violation even if it is nowhere near a window on its own building.

Flashings and prohibited uses

IPC 903.3 Flashings : the juncture of each vent pipe with the roof line shall be made watertight by an approved flashing . Materials come from IPC 902.2 and 902.3 — sheet copper not less than 8 ounces per square foot , field-constructed sheet lead not less than 3 pounds per square foot , prefabricated sheet lead not less than 2-1/2 pounds per square foot .

IPC 903.4 Prohibited use : a vent terminal shall not be used for any purpose other than a vent terminal . Anchoring a satellite dish, a guy wire or a lightning rod to a vent stack is a code violation, not merely bad practice.

Applying the rules to one roof

A two-story house in a jurisdiction with a 97.5-percent design temperature of minus 5 degrees F has a sloped roof. The plumber proposes:

Proposal Model IPC result

2-inch vent through the roof Fails 903.2 — the design temperature is 0 degrees F or less, so the extension must be not less than 3 inches

Increase from 2-inch to 3-inch at the roof deck Fails 903.2 — the increase must be made not less than 1 foot inside the thermal envelope

Vent terminal 4 feet horizontally from an openable bedroom window, 1 foot above its head Fails 903.5 — within 10 feet horizontally and not 3 feet or more above the top of the opening

Vent terminal 4 feet horizontally from the same window, 3 feet 6 inches above its top Complies with 903.5

Solar panel mounted over the vent, terminal 2 inches above the roof Complies with 903.1.3 if the open area is not less than the pipe area, the assembly resists snow and wind, and birds and rodents are excluded

Exterior vent run up the gable wall, uninsulated Fails 903.6 — the design temperature is less than 0 degrees F, so insulation, heat or both are required

Aluminum flashing at the roof line Complies with 903.3 if approved; copper and lead have specified minimum weights

Now change the jurisdiction to Colorado, and two of those answers change: 903.2 is deleted , so a 2-inch vent through the roof is acceptable, and the terminal must extend at least 6 inches above the roof under the Colorado amendment to 903.1.1. Everything else — 903.5 location, 903.1.4 sidewall, 903.3 flashing, 903.6 exterior freeze protection — is unchanged.

Loading diagram... Vent terminal requirements