Study guide

12.4 Putting a Vent System Together: A Worked Building

Colorado Journeyworker Plumber Journeyman Plumber

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Passing the Colorado Journeyworker Plumber Exam

1.1 Exam Blueprint, Format, and the 2024 Code Changeover 1.2 Colorado Licenses, Experience Hours, and Apprentice Supervision 1.3 Permits, Inspections, Blue Tags, and Board Enforcement

2 Chapter 2: General Regulations (IPC Chapter 3)

2.1 Approved Materials, Certification, and General Installation Rules 2.2 Protection of Pipes: Contact, Notching, Shield Plates, and Freezing 2.3 Piping Support, Trenching, Bedding, and Backfill 2.4 Required Tests: Water, Air, and Backflow Assembly Testing

3 Chapter 3: Fixtures and Equipment (IPC Chapter 4)

3.1 Minimum Fixture Counts, Separate Facilities, and Toilet Room Location 3.2 Fixture Clearances, Compartments, and Setting Requirements 3.3 Water Closets, Urinals, Lavatories, Sinks, and Flush Devices 3.4 Showers, Bathtubs, Fixture Fittings, and Scald Protection

4 Chapter 4: Water Heaters (IPC Chapter 5)

4.1 Water Heater Installation, Location, Access, and Clearances 4.2 Relief Valves and Discharge Piping 4.3 Water Heater Pans, Pan Drains, and Storage Tank Requirements 4.4 Thermal Expansion Control and Hot Water Temperature Limits

5 Chapter 5: Water Supply Materials and Installation (IPC Chapter 6)

5.1 Water Service and Distribution Materials, and Sewer Separation 5.2 Joints, Connections, and Dissimilar Materials in Water Piping 5.3 Valves, Shutoffs, and Required Valve Locations

6 Chapter 6: Water Supply Sizing and Pressure (IPC Chapter 6 and Appendix E)

6.1 Pressure Limits, Pressure Reducing Valves, and Water Hammer 6.2 Water Supply Fixture Units and Estimating Demand 6.3 Sizing Water Piping with Appendix E and Table E104.1

7 Chapter 7: Cross-Connection Control and Backflow Prevention (IPC Sections 608-610, Chapter 13)

7.1 Cross-Connection Principles, Backsiphonage, and Backpressure 7.2 Air Gaps and the Backflow Preventer Family 7.3 Applying Backflow Protection to Specific Connections 7.4 Nonpotable Water Systems, Identification, and Reclaimed Water

8 Chapter 8: Sanitary Drainage Materials and Fittings (IPC Chapter 7)

8.1 Sanitary Drainage Materials and Where Each May Be Used 8.2 Drainage Joints, Transitions, and Prohibited Connections 8.3 Fittings for Change of Direction and Drainage Flow Patterns

9 Chapter 9: Sanitary Drainage Sizing (IPC Sections 704, 709-711)

9.1 Drainage Fixture Units and Load Estimation 9.2 Slope of Horizontal Drainage and Installation Rules 9.3 Sizing Building Drains, Building Sewers, and Horizontal Branches 9.4 Stacks, Branch Intervals, and Offsets in Tall Buildings

10 Chapter 10: Cleanouts, Sumps and Below-Sewer Drainage (IPC Sections 708, 712-716)

10.1 Cleanouts, Manholes, and Access Requirements 10.2 Backwater Valves and Fixtures Below the Sewer Level 10.3 Sumps, Sewage Ejectors, and Macerating Toilet Systems 10.4 Building Sewers, Private Disposal, and Special Drainage Conditions

11 Chapter 11: Vent Fundamentals and Terminals (IPC Sections 901-905, 908)

11.1 How Vents Work, Trap Seal Loss, and the One-Inch Rule 11.2 Vent Terminals, Roof Penetrations, and Sidewall Terminations 11.3 Vent Connections, Grade, and the Six-Inch Rules

12 Chapter 12: Vent Types and Sizing (IPC Sections 906-911, 917)

12.1 Individual Vents, Common Vents, and Vents for Stack Offsets 12.2 Trap-to-Vent Distance, Trap Arms, and Fixture Drains 12.3 Sizing Stack Vents, Vent Stacks, Branch Vents, and Headers 12.4 Putting a Vent System Together: A Worked Building

13 Chapter 13: Engineered and Special Venting (IPC Sections 912-916, 918-920)

13.1 Horizontal and Vertical Wet Venting 13.2 Waste Stack Vents, Circuit Vents, and Combination Waste and Vent 13.3 Island Fixture Venting and Air Admittance Valves

14 Chapter 14: Traps, Interceptors and Separators (IPC Chapter 10)

14.1 Fixture Traps, Trap Seals, and Prohibited Trap Types 14.2 Trap Seal Protection, Primers, and Barrier Devices 14.3 Grease Interceptors, Oil Separators, and Solids Interceptors

15 Chapter 15: Indirect and Special Waste (IPC Chapter 8)

15.1 Where Indirect Waste Is Required, and Air Gap Versus Air Break 15.2 Waste Receptors, Hub Drains, and Standpipes 15.3 Special Wastes, Chemical Neutralization, and Health Care Drainage

16 Chapter 16: Storm Drainage (IPC Chapter 11 and Appendix B)

16.1 Storm Drainage Scope, Disposal, and Prohibited Connections 16.2 Storm Drainage Materials, Roof Drains, and Conductors 16.3 Secondary Roof Drains, Scuppers, and Controlled Flow Systems 16.4 Rainfall Rates, Roof Area, and the Flow-Rate Conversion 16.5 Sizing Vertical Conductors, Leaders, and Storm Drains 16.6 Gutters, Subsoil Drains, Building Subdrains, and Storm Sumps

17 Chapter 17: Residential Fire Sprinklers (IRC Section P2904)

17.1 Residential Fire Sprinkler Systems (IRC Section P2904)

18 Chapter 18: Isometric Analysis and Plumbing Calculations

18.1 Reading Plumbing Isometrics and Riser Diagrams 18.2 Analyzing a DWV Isometric for Code Compliance 18.3 Offsets, Travel, and the Plumbing Math the Exam Assumes

12.4 Putting a Vent System Together: A Worked Building

Key Takeaways Explain This Topic AI

IPC 904.1 requires at least one dry vent extending to the outdoors for each building drain, and it may not be an island fixture vent.

IPC 918.7 requires at least one stack vent or vent stack in each plumbing system to extend outdoors to the open air.

IPC 904.2 requires a vent stack for every drainage stack of five or more branch intervals, excepting waste stack vent systems under Section 913.

IPC 905.4 requires every dry vent to rise vertically to 6 inches above the flood level rim of the highest trap being vented before offsetting.

IPC 903.5 prohibits a vent terminal within 10 feet horizontally of a door, openable window or air intake unless it is 3 feet or more above the opening.

Last updated: September 2026

The design sequence

Work these seven steps in order and the venting method for any building falls out.

Count the branch intervals on each drainage stack. Five or more triggers a vent stack (904.2).

Confirm the outdoor vent. At least one dry vent to the outdoors per building drain (904.1), and at least one stack vent or vent stack to open air in the system (918.7).

Pick a venting method for every trap. Individual, common, wet, waste stack, circuit, combination waste and vent, island, single-stack, or air admittance valve. Every trap must fall under a named method (901.2.1).

Check every trap arm against Table 909.1 and the fall rule in 909.2, and confirm no vent is within two pipe diameters of a weir (909.3).

Size each vent — 906.1 for stack vents and vent stacks, 906.2 for everything else, plus the 40-foot increase and the two floors.

Verify connection elevations — above the centerline of horizontal drains (905.3), 6 inches above the flood level rim for vertical rises (905.4) and for vent-to-vent connections and horizontal branch, relief and loop vents (905.5), and gravity grade back to the drain (905.2).

Place the terminal — 903.1 method, 903.5 location, 903.2 frost closure (model code), 903.3 flashing.

Worked building A: a four-story apartment building

Given: four stories, one branch interval per floor. Each floor has two apartments; each apartment has a bathroom group (water closet 3 dfu, lavatory 1 dfu, tub-shower 2 dfu = 5 dfu as a group) and a kitchen sink (2 dfu). One 4-inch soil stack serves all eight apartments. Floor-to-floor is 10 feet; the stack runs 46 feet from the building drain to the roof terminal.

Step 1 — branch intervals. Four floors at 10 feet each = four branch intervals . That is fewer than five , so no vent stack is required under 904.2. The stack vent alone may serve.

Change the building to five stories and the answer flips: a vent stack becomes mandatory , connecting at the base of the drainage stack at or below the lowest horizontal branch (904.4).

Step 2 — outdoor vent. The stack vent — the extension of the soil stack above the highest horizontal branch — carries the system to open air. That satisfies both 904.1 and 918.7.

Step 3 — drainage load and stack size. Total = 8 x (5 + 2) = 56 dfu . Per branch interval: 2 x 7 = 14 dfu . From Table 710.1(2):

Stack greater than three branch intervals: 3-inch = 72 dfu. 56 dfu fits a 3-inch stack.

Single branch interval: 3-inch allows 20 dfu ; 14 dfu fits.

But the stack serves water closets , and Table 710.1(1) footnote a requires the building drain serving a water closet to be at least 3 inches. A 3-inch stack is workable; a 4-inch stack gives margin and is the common choice.

Step 4 — venting methods per bathroom. Each bathroom group is a candidate for horizontal wet venting under 912.1 (any combination of fixtures within two bathroom groups on the same floor level). The kitchen sink is not a bathroom group fixture, so it must discharge downstream of the horizontal wet vent (912.1) and be separately vented — an individual vent, or common vented with another fixture on the same floor.

Step 5 — trap arms. Lavatory 1-1/4-inch trap: 5 feet maximum (Table 909.1). Tub 1-1/2-inch trap: 6 feet . Kitchen sink 1-1/2-inch trap: 6 feet . Water closet: unlimited (909.1 exception).

Step 6 — vent sizing.

Kitchen sink individual vent: the sink drain is 1-1/2 inches; half is 3/4 inch, below the floor, so 1-1/4 inches .

The branch vent collecting the kitchen sink vents on all four floors runs roughly 42 feet to the stack vent. Over 40 feet — increase one nominal size for the entire length: 1-1/2 inches .

Stack vent: sized from Table 906.1 at 4-inch stack, 56 dfu, 46 feet developed length; never less than half of 4 inches = 2 inches .

Step 7 — connections and terminal.

Every dry vent rises to 6 inches above the flood level rim of the highest fixture it vents before offsetting (905.4).

Branch vents run horizontally 6 inches above the flood level rim of the highest fixture served (905.5).

All vent piping grades back to the drain (905.2).

The terminal goes through the roof at the jurisdiction's height (903.1.1), not within 10 feet horizontally of any openable window unless 3 feet above it (903.5), flashed watertight (903.3), and — under the model code — not less than 3 inches in diameter if the 97.5 percent design temperature is 0 degrees F or below (903.2).

Worked building B: a single-family house

Given: two full bathrooms upstairs, a powder room and a kitchen downstairs, a laundry, and a basement floor drain. One 3-inch stack.

Fixture group Method Why

Upstairs hall bath and master bath, same floor Horizontal wet vent (912.1) Two bathroom groups on the same floor level is exactly the 912.1 allowance

Downstairs powder room Individual vents or common vent with the adjacent lavatory (910, 911) Only two fixtures

Kitchen sink on an island Island fixture vent (916) Sinks and lavatories only; residential kitchen sink with dishwasher and disposer is expressly permitted

  • Laundry standpipe Individual vent Standpipe trap arm within Table 909.1
  • Basement floor drain Trap seal primer plus a vent per one of the chapter's methods 1002.4.1 and 901.2.1

Two hard checks on this house:

The island vent may not be the required outdoor vent. IPC 904.1.1 states the required vent shall not be an island fixture vent . The 3-inch stack vent through the roof is the required outdoor vent.

The island vent needs cleanouts. IPC 916.3 requires cleanouts in the island fixture vent to permit rodding of all vent piping located below the flood level rim , with rodding in both directions permitted through a cleanout .

Common failures an inspector writes up

  • Finding Section violated
  • Lavatory vent turns horizontal below the lavatory rim 905.4
  • Vent tapped into the side of a horizontal drain at the centerline 905.3
  • Vent taken off the trap arm 2 inches downstream of a 2-inch trap weir 909.3 (needs 4 inches)
  • 1-1/2 inch trap arm running 8 feet to the vent Table 909.1 (6 feet maximum)
  • 55-foot branch vent left at the minimum size 906.2, 40-foot rule
  • Three fixtures on one "common vent" 911.1 (common vent serves two )
  • Common vent with a water closet as the upper fixture at different levels 911.3
  • Kitchen sink tied into the wet-vented bathroom branch upstream of the last bathroom fixture 912.1
  • Five-branch-interval stack with no vent stack 904.2
  • Every vent on air admittance valves, none to open air 918.7
  • Sidewall vent under a soffit-vented overhang 903.1.4
  • Vent terminal 5 feet from a bedroom window, level with its head 903.5
  • Vent belly holding condensate 905.2

Loading diagram... Seven-step vent design sequence