Study guide
4.4 Thermal Expansion Control and Hot Water Temperature Limits
Colorado Journeyworker Plumber Journeyman Plumber
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Passing the Colorado Journeyworker Plumber Exam
1.1 Exam Blueprint, Format, and the 2024 Code Changeover 1.2 Colorado Licenses, Experience Hours, and Apprentice Supervision 1.3 Permits, Inspections, Blue Tags, and Board Enforcement
2 Chapter 2: General Regulations (IPC Chapter 3)
2.1 Approved Materials, Certification, and General Installation Rules 2.2 Protection of Pipes: Contact, Notching, Shield Plates, and Freezing 2.3 Piping Support, Trenching, Bedding, and Backfill 2.4 Required Tests: Water, Air, and Backflow Assembly Testing
3 Chapter 3: Fixtures and Equipment (IPC Chapter 4)
3.1 Minimum Fixture Counts, Separate Facilities, and Toilet Room Location 3.2 Fixture Clearances, Compartments, and Setting Requirements 3.3 Water Closets, Urinals, Lavatories, Sinks, and Flush Devices 3.4 Showers, Bathtubs, Fixture Fittings, and Scald Protection
4 Chapter 4: Water Heaters (IPC Chapter 5)
4.1 Water Heater Installation, Location, Access, and Clearances 4.2 Relief Valves and Discharge Piping 4.3 Water Heater Pans, Pan Drains, and Storage Tank Requirements 4.4 Thermal Expansion Control and Hot Water Temperature Limits
5 Chapter 5: Water Supply Materials and Installation (IPC Chapter 6)
5.1 Water Service and Distribution Materials, and Sewer Separation 5.2 Joints, Connections, and Dissimilar Materials in Water Piping 5.3 Valves, Shutoffs, and Required Valve Locations
6 Chapter 6: Water Supply Sizing and Pressure (IPC Chapter 6 and Appendix E)
6.1 Pressure Limits, Pressure Reducing Valves, and Water Hammer 6.2 Water Supply Fixture Units and Estimating Demand 6.3 Sizing Water Piping with Appendix E and Table E104.1
7 Chapter 7: Cross-Connection Control and Backflow Prevention (IPC Sections 608-610, Chapter 13)
7.1 Cross-Connection Principles, Backsiphonage, and Backpressure 7.2 Air Gaps and the Backflow Preventer Family 7.3 Applying Backflow Protection to Specific Connections 7.4 Nonpotable Water Systems, Identification, and Reclaimed Water
8 Chapter 8: Sanitary Drainage Materials and Fittings (IPC Chapter 7)
8.1 Sanitary Drainage Materials and Where Each May Be Used 8.2 Drainage Joints, Transitions, and Prohibited Connections 8.3 Fittings for Change of Direction and Drainage Flow Patterns
9 Chapter 9: Sanitary Drainage Sizing (IPC Sections 704, 709-711)
9.1 Drainage Fixture Units and Load Estimation 9.2 Slope of Horizontal Drainage and Installation Rules 9.3 Sizing Building Drains, Building Sewers, and Horizontal Branches 9.4 Stacks, Branch Intervals, and Offsets in Tall Buildings
10 Chapter 10: Cleanouts, Sumps and Below-Sewer Drainage (IPC Sections 708, 712-716)
10.1 Cleanouts, Manholes, and Access Requirements 10.2 Backwater Valves and Fixtures Below the Sewer Level 10.3 Sumps, Sewage Ejectors, and Macerating Toilet Systems 10.4 Building Sewers, Private Disposal, and Special Drainage Conditions
11 Chapter 11: Vent Fundamentals and Terminals (IPC Sections 901-905, 908)
11.1 How Vents Work, Trap Seal Loss, and the One-Inch Rule 11.2 Vent Terminals, Roof Penetrations, and Sidewall Terminations 11.3 Vent Connections, Grade, and the Six-Inch Rules
12 Chapter 12: Vent Types and Sizing (IPC Sections 906-911, 917)
12.1 Individual Vents, Common Vents, and Vents for Stack Offsets 12.2 Trap-to-Vent Distance, Trap Arms, and Fixture Drains 12.3 Sizing Stack Vents, Vent Stacks, Branch Vents, and Headers 12.4 Putting a Vent System Together: A Worked Building
13 Chapter 13: Engineered and Special Venting (IPC Sections 912-916, 918-920)
13.1 Horizontal and Vertical Wet Venting 13.2 Waste Stack Vents, Circuit Vents, and Combination Waste and Vent 13.3 Island Fixture Venting and Air Admittance Valves
14 Chapter 14: Traps, Interceptors and Separators (IPC Chapter 10)
14.1 Fixture Traps, Trap Seals, and Prohibited Trap Types 14.2 Trap Seal Protection, Primers, and Barrier Devices 14.3 Grease Interceptors, Oil Separators, and Solids Interceptors
15 Chapter 15: Indirect and Special Waste (IPC Chapter 8)
15.1 Where Indirect Waste Is Required, and Air Gap Versus Air Break 15.2 Waste Receptors, Hub Drains, and Standpipes 15.3 Special Wastes, Chemical Neutralization, and Health Care Drainage
16 Chapter 16: Storm Drainage (IPC Chapter 11 and Appendix B)
16.1 Storm Drainage Scope, Disposal, and Prohibited Connections 16.2 Storm Drainage Materials, Roof Drains, and Conductors 16.3 Secondary Roof Drains, Scuppers, and Controlled Flow Systems 16.4 Rainfall Rates, Roof Area, and the Flow-Rate Conversion 16.5 Sizing Vertical Conductors, Leaders, and Storm Drains 16.6 Gutters, Subsoil Drains, Building Subdrains, and Storm Sumps
17 Chapter 17: Residential Fire Sprinklers (IRC Section P2904)
17.1 Residential Fire Sprinkler Systems (IRC Section P2904)
18 Chapter 18: Isometric Analysis and Plumbing Calculations
18.1 Reading Plumbing Isometrics and Riser Diagrams 18.2 Analyzing a DWV Isometric for Code Compliance 18.3 Offsets, Travel, and the Plumbing Math the Exam Assumes
4.4 Thermal Expansion Control and Hot Water Temperature Limits
Key Takeaways Explain This Topic AI
IPC 607.3 requires a thermal expansion control device where a storage water heater's cold water supply passes through a check valve, pressure reducing valve or backflow preventer.
IPC 607.3 requires the expansion control device to be connected downstream of all check valves, pressure reducing valves and backflow preventers.
IPC 504.4 states expressly that the relief valve shall not be used as a means of controlling thermal expansion.
IPC 607.3 requires expansion tanks to be sized so that the water distribution system pressure does not exceed that required by IPC 604.8, which limits static pressure to 80 psi.
IPC 501.6 limits water from tankless water heaters to not greater than 140 degrees F for domestic uses, without superseding the 120 degree F shower valve rule of IPC 412.3.
Last updated: September 2026
Why a closed system is a problem
Water expands roughly 2 percent in volume when heated from 60 degrees F to 140 degrees F. In an open system — one where the cold supply connects back to the main with no one-way device — that expansion simply pushes back toward the street and nothing happens.
Install a check valve, a pressure reducing valve, or a backflow preventer on the service, and the system becomes closed . The expanded volume has nowhere to go, and because water is nearly incompressible, a tiny volume increase drives a very large pressure increase. A 50-gallon heater recovering from cold can lift static pressure in a closed system from 60 psi to well past 150 psi in minutes. Symptoms: the T&P valve weeps, faucet cartridges fail early, toilet fill valves chatter, and the tank's glass lining can craze.
What the code requires — IPC 607.3
Where a storage water heater is supplied with cold water that passes through a check valve, pressure reducing valve or backflow preventer , a thermal expansion control device shall be connected to the water heater cold water supply pipe at a point that is downstream of all check valves, pressure reducing valves and backflow preventers . Thermal expansion tanks shall be sized in accordance with the tank manufacturer's instructions and shall be sized such that the pressure in the water distribution system shall not exceed that required by Section 604.8 .
Four separate requirements sit inside that paragraph:
Trigger : any one of three one-way devices in the cold supply.
Location : on the water heater cold water supply pipe , downstream of all such devices. Upstream is useless — the expanded water cannot reach it.
Sizing : per the manufacturer's instructions , not by a code table.
Performance ceiling : the result must keep distribution pressure within IPC 604.8 , which limits static water pressure to not more than 80 psi at fixture supply pipes (a pressure reducing valve is required where the supply exceeds 80 psi).
And from the safety-device side, IPC 504.4 : " The relief valve shall not be used as a means of controlling thermal expansion. " A weeping T&P valve is evidence of a missing or failed expansion control, and replacing the T&P valve does not correct the violation.
IPC 308.10 requires thermal expansion tanks to be supported — a full 4.4-gallon tank hanging off a 3/4-inch copper stub is a mechanical failure waiting to happen.
Diagnosing a closed system in the field
- Observation Likely meaning
- Gauge on a hose bibb reads 60 psi in the morning, 140 psi after a shower Closed system, no expansion control
- T&P weeps only after heavy hot water use, never overnight Thermal expansion, not an over-temperature condition
T&P discharges continuously at any time Failed valve, over-temperature control, or genuine over-pressure from the street
Expansion tank sounds full and heavy when tapped Waterlogged tank — bladder failed; replace and recharge
PRV installed at the meter within the last year, complaints started then The PRV closed the system; add expansion control downstream
An expansion tank's air precharge must match the system static pressure before installation. A tank precharged at the factory to 40 psi, installed on a 65 psi system, is already fully compressed at rest and absorbs almost nothing.
The system pressure rules this connects to
Section Rule
604.8 Maximum static water pressure at fixture supply pipes: 80 psi ; a pressure reducing valve is required above that
- 607.3 Thermal expansion control where a check valve, PRV or backflow preventer is present
- 504.4 Relief valve is not an expansion control
- 504.5 Relief valve pressure setting: rated working pressure or 150 psi , whichever is less
- 308.10 Thermal expansion tanks must be supported
- Temperature limits, collected
Water Heaters items frequently test the temperature ceilings across the whole system. Gather them in one place:
- Point in the system Limit Section
- Relief valve temperature setting 210 F 504.5
- Combination water/space heating into the potable distribution system 140 F 501.2
- Tankless water heater output for domestic use 140 F 501.6
- Shower or tub-shower valve maximum setting 120 F 412.3, 412.4
- Bathtub / whirlpool valve 120 F 412.5
- Footbath, pedicure bath, head shampoo faucet 120 F 423.3, 412.10
Tempered water at public hand-washing lavatories 85-110 F (device set to not greater than 110 F) 419.5, 607.1.2
- Bidet 110 F 408.3
- Water entering cold piping from a demand recirculation pump 104 F 607.2.1.2
Read the direction of each limit. 210 F is the highest number in the table, and it is not a delivery temperature at all — it is the point at which a safety device must open. 140 F is a system delivery cap. Everything at 120 F or below is a point-of-use cap protecting a bather's skin.
IPC 607.1.1 adds an important qualifier: the water heater's thermostat control may serve as the temperature-limiting means for the code's maximum delivery temperature only where the heater complies with ASSE 1082 or ASSE 1085 . On an ordinary heater, turning the thermostat down is not a code-compliant substitute for the required mixing or limiting device.
Storing hot, delivering warm
Legionella control and scald protection pull in opposite directions. The common engineered answer, permitted by the code, is to store at a higher temperature and mix down at or near the point of use :
Store at 140 F, allowed by 501.2 and 501.6 as a distribution ceiling.
Use an ASSE 1017 thermostatic mixing valve at the heater to deliver tempered water, per 607.1.2.
Use an ASSE 1016 balanced-pressure, thermostatic or combination valve at each shower, limited to 120 F , per 412.3 — and recall that in-line thermostatic valves may not be used for that purpose.
Use an ASSE 1070 limiting device at public lavatories for tempered water, per 419.5.
Worked example: a service call
A homeowner reports the T&P valve on a 3-year-old 50-gallon gas heater "leaks every evening." The water purveyor installed a new meter with an integral dual check valve four months ago.
Static pressure test at a hose bibb: 62 psi cold, 148 psi after a load of laundry and two showers. That confirms thermal expansion in a closed system .
Cause : the meter's dual check valve closed the system (607.3 trigger).
Wrong fix : replace the T&P valve. IPC 504.4 forbids using the relief valve as expansion control, and the new valve will weep too.
Right fix : install a thermal expansion tank on the cold water supply to the heater, downstream of the check valve , sized per the manufacturer's instructions, precharged to the 62 psi measured static pressure, and supported per 308.10.
Verify : after installation, hot water use should no longer drive static pressure above 80 psi (604.8), and the T&P should stay dry.
Also check : if incoming street pressure had been above 80 psi, a pressure reducing valve would be required by 604.8 as well — and that PRV would itself be a 607.3 trigger.