Study guide
6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics
Colorado Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: State Laws, Regulations & CCWP Certification
1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting
2 Chapter 2: Source Water & Drinking Water Treatment Processes
2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle
3 Chapter 3: Disinfection & Chemical Addition
3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices
4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance
4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management
5 Chapter 5: Wastewater Treatment Principles & Biological Processes
5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects
6 Chapter 6: Advanced Wastewater Treatment & Solids Management
6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84
7 Chapter 7: Water Distribution Systems
7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems
8 Chapter 8: Wastewater Collection Systems
8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment
9 Chapter 9: Pumps, Motors & Utility Mechanics
9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control
10 Chapter 10: Laboratory Analysis & Water Quality Monitoring
10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)
11 Chapter 11: Operator Mathematics & Applied Calculations
11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance
12 Chapter 12: Safety, Emergency Operations & Compliance
12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties
6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics
Key Takeaways Explain This Topic AI
Surface overflow rate is calculated on influent flow alone because it represents upflow velocity, while solids loading rate must include the RAS flow because those solids also pass through the tank.
Solids loading rate rather than surface overflow rate usually limits an activated sludge clarifier, because the unit must thicken as well as clarify.
Rising sludge from denitrification is distinguished from bulking by a normal sludge volume index and by discrete chunks of well-formed floc floating after settling well.
The settled volume method estimates RAS percentage as SSV30 divided by 1,000 minus SSV30, times 100.
An unlevel or algae-fouled weir creates a locally high overflow rate and is one of the most common and most correctable causes of solids carryover.
Last updated: August 2026
The clarifier is where activated sludge succeeds or fails
The aeration basin grows the biomass. The secondary clarifier has to separate it, thicken it for return, and produce a clear effluent — all at once. A plant with a perfect biological process and a failing clarifier will violate its permit, because the permit is written on effluent TSS , and every pound of solids that leaves over the weir is both a violation and a loss of inventory.
Three simultaneous duties
Clarification — produce a low-solids overflow.
Thickening — concentrate the settled sludge so the return stream carries solids back at 4,000 to 12,000 mg/L rather than at mixed liquor concentration.
Sludge storage — hold a working blanket that buffers flow variation.
Design and loading parameters
- Parameter Formula Typical range
- Surface overflow rate (SOR) Flow (gpd) / surface area (sq ft) 400 to 800 gpd/sq ft at average flow
- Solids loading rate (SLR) lbs solids per day / surface area 20 to 30 lbs/day/sq ft
- Weir overflow rate Flow (gpd) / weir length (ft) 10,000 to 20,000 gpd/ft
- Hydraulic detention time Volume / flow 2 to 4 hours
Sludge blanket depth Measured with a core sampler or blanket detector 1 to 3 ft, roughly 1/4 to 1/3 of side water depth
Two of these deserve emphasis. Surface overflow rate is the upflow velocity in disguise : a particle settles out only if its settling velocity exceeds the rate at which water rises to the weir. Raise the flow and you raise the upflow velocity, and the slower-settling particles are carried out. Solids loading rate , not SOR, is usually what limits an activated sludge clarifier, because the unit must thicken as well as clarify. Note also that when you calculate SOR and SLR, SOR uses influent flow only, while SLR must include the RAS flow , because returned solids pass through the tank too.
Worked example. A circular secondary clarifier is 75 ft in diameter, receiving 2.4 MGD of plant flow plus 1.2 MGD of RAS, with MLSS of 2,800 mg/L.
- Area = 0.785 x 75² = 0.785 x 5,625 = 4,416 sq ft
- SOR = 2,400,000 gpd / 4,416 sq ft = 543 gpd/sq ft (RAS excluded)
- Solids load = (2.4 + 1.2) MGD x 2,800 mg/L x 8.34 = 3.6 x 2,800 x 8.34 = 84,067 lbs/day
- SLR = 84,067 / 4,416 = 19.0 lbs/day/sq ft
Both are within normal range, so a settling problem at this plant would point to sludge quality rather than to hydraulic overload.
Circular versus rectangular
Circular clarifiers feed through a center column into a flocculating center well, flow radially outward, and are swept by a rotating rake to a center hopper. Some use a suction (Tow-Bro or riser pipe) mechanism that withdraws sludge across the full radius rather than plowing it to the center, which reduces the time solids spend in the tank.
Rectangular clarifiers use chain-and-flight or traveling bridge collectors moving sludge to a hopper at one end. They share common walls, so they are efficient on land, and they are less prone to density currents at high side water depth.
The inlet baffle or flocculating center well is critical in either geometry: it dissipates inlet energy so the incoming mixed liquor does not shoot across the tank, and it gives floc particles a chance to collide and grow.
Density currents and short-circuiting
Mixed liquor entering a clarifier is denser than the clear water in the tank. It sinks, travels along the floor, hits the far wall, and rises — a density current . If it rises near the weir, it carries solids over. Countermeasures are deeper side water depth, inboard weir placement with a Stamford or peripheral baffle that deflects the rising current back toward the center, and adequate inlet energy dissipation.
Short-circuiting from wind, temperature differences, uneven weirs, or a poorly placed inlet reduces the effective detention time. An unlevel weir is one of the most common and most correctable causes: water preferentially runs over the low spot, creating a high local overflow rate. Weirs are checked with a level and adjusted, and they are kept clean of algae, which both plugs the notches and sloughs into the effluent.
Reading the clarifier
The surface of a secondary clarifier is the most informative diagnostic view in a wastewater plant.
- Observation Interpretation
- Clear water with a crisp blanket Healthy operation
- Fine, dispersed particles in the effluent (pin floc) Over-aged sludge, excessive sludge age; increase wasting
Cloudy, turbid supernatant with no discrete particles Young sludge, low sludge age, or toxic shock; decrease wasting
Large chunks of sludge rising to the surface Denitrification in the blanket — nitrate reduced to nitrogen gas that floats the floc
Blanket climbing steadily toward the weir Solids loading exceeds thickening capacity, or RAS rate is too low, or SVI has risen
- Dark brown greasy foam accumulating Nocardia or excessive sludge age
- White billowing foam Young sludge, low MLSS, or surfactant
- Ashing — small dark particles floating Denitrification or old sludge fragments
Rising sludge from denitrification is the classic exam item and it is often confused with bulking. In a bulking event the sludge settles slowly but does not float; the SVI is high and the blanket rises gradually. In rising sludge, well-settled sludge sits on the bottom, and after some time in the anoxic blanket, denitrifying organisms convert nitrate to nitrogen gas which becomes trapped in the floc and floats discrete chunks to the surface. The distinguishing evidence is that the floating clumps still look like good floc and the settleometer shows a normal SVI. Remedies are to increase the RAS rate to shorten sludge residence time in the blanket, reduce sludge blanket depth, increase wasting to lower sludge age, or provide an intentional anoxic zone upstream so denitrification happens where it is wanted.
Return activated sludge rate
RAS is the operator's primary lever on the clarifier. Too low, and solids accumulate in the blanket until it reaches the weir. Too high, and the clarifier is hydraulically overloaded, the sludge is returned thin, and the aeration basin retention time falls.
Common approaches to setting RAS:
Percentage of influent flow , typically 20 to 100 percent, adjusted as flow changes.
Settleometer-based (SSV method): RAS percentage is estimated from the 30-minute settled sludge volume, since RAS % ≈ SSV30 / (1,000 − SSV30) x 100.
Sludge blanket control: adjust RAS to hold a target blanket depth.
Solids mass balance: return enough solids to hold the target MLSS.
Worked example. A settleometer shows SSV30 of 280 mL/L. The estimated RAS rate is 280 / (1,000 − 280) x 100 = 280 / 720 x 100 = 38.9 percent of influent flow.
Secondary clarifier maintenance
Inspect and adjust weir levelness annually and after any structural work; clean weirs and troughs of algae routinely.
Check rake or flight mechanism torque ; a rising torque alarm means the blanket is too deep or debris is jammed.
Inspect chain, flight, and sprocket wear on rectangular units and drive gear oil on circular units.
Verify the scum skimmer, beach, and scum box are removing rather than recirculating floatables.
Confirm the RAS and WAS pump flow meters are accurate — every process control calculation depends on them.
Dewater and inspect the basin on a multi-year cycle for corrosion, concrete condition, and baffle integrity.