Study guide
6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64)
Colorado Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: State Laws, Regulations & CCWP Certification
1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting
2 Chapter 2: Source Water & Drinking Water Treatment Processes
2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle
3 Chapter 3: Disinfection & Chemical Addition
3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices
4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance
4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management
5 Chapter 5: Wastewater Treatment Principles & Biological Processes
5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects
6 Chapter 6: Advanced Wastewater Treatment & Solids Management
6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84
7 Chapter 7: Water Distribution Systems
7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems
8 Chapter 8: Wastewater Collection Systems
8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment
9 Chapter 9: Pumps, Motors & Utility Mechanics
9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control
10 Chapter 10: Laboratory Analysis & Water Quality Monitoring
10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)
11 Chapter 11: Operator Mathematics & Applied Calculations
11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance
12 Chapter 12: Safety, Emergency Operations & Compliance
12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties
6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64)
Key Takeaways Explain This Topic AI
Mechanical dewatering transforms liquid digested sludge (2%–5% solids) into a transportable semi-solid cake (15%–35% solids), drastically reducing hauling and disposal volumes.
Belt filter presses (BFPs) operate across three zones (gravity drainage, wedge, and high-pressure shear rollers), producing 15%–25% cake solids with lower energy consumption than centrifuges.
Solid bowl decanter centrifuges utilize high rotational G-forces (1,000–3,000 Gs) and differential scroll conveyor speeds to generate 20%–30% cake solids with enclosed odor control.
Colorado Regulation 64 (5 CCR 1002-64) and EPA Part 503 govern biosolids recycling, distinguishing Class A (Exceptional Quality, undetectable pathogens, unrestricted use) from Class B (significant pathogen reduction, strict site and harvesting restrictions).
Vector Attraction Reduction (VAR) mandates must be satisfied through one of 10 EPA/Reg 64 compliance options, such as achieving at least 38% Volatile Solids Reduction (VSR) or direct subsurface soil injection within 8 hours.
Last updated: August 2026
Dewatering Equipment & Biosolids Management (Colorado Regulation 64)
Liquid digested sludge typically contains 95 % – 98 % 95\%\text{--}98\% 95% – 98% water ( 2.0 % – 5.0 % 2.0\%\text{--}5.0\% 2.0% – 5.0% dry solids). Hauling liquid sludge to land application sites or landfills is economically unsustainable due to enormous transportation volumes. Mechanical dewatering extracts free, capillary, and interstitial water from stabilized solids, transforming liquid sludge into a handleable, semi-solid "cake" containing 15 % – 35 % 15\%\text{--}35\% 15% – 35% dry solids .
Once dewatered and stabilized, sewage sludge residuals are legally classified as biosolids and regulated under the federal EPA 40 CFR Part 503 rule and Colorado's state-specific Regulation 64: Biosolids Regulation (5 CCR 1002-64) . Certified operators must master both mechanical dewatering operations and stringent environmental compliance standards governing pathogen reduction, vector attraction reduction, and heavy metal concentrations.
1. Mechanical Dewatering Technologies +-----------------------------------------------------------------------------------------+
- | MECHANICAL DEWATERING EQUIPMENT COMPARISON |
- +-----------------------------------------------------------------------------------------+
- | Parameter | Belt Filter Press (BFP) | Decanter Centrifuge | Plate & Frame Press|
- +-------------------+-------------------------+----------------------+--------------------+
- | Typical Cake % TS | 15% - 25% dry solids | 20% - 30% dry solids | 35% - 50% dry solids|
- | Power Consumption | Low (2 - 10 HP) | High (25 - 150 HP) | Moderate |
- | Odor / Aerosols | Open (Higher odor/mist) | Enclosed (Excellent) | Open during cake drop|
- | Operation Mode | Continuous | Continuous | Batch cycle |
- | Conditioning Aid | Cationic Polymer | Cationic Polymer | Lime + FeCl3 / Poly|
- | Washwater Demand | High (80-120 psi continuous)| Low (Periodic flush)| Moderate |
- +-----------------------------------------------------------------------------------------+
- Belt Filter Presses (BFP)
A Belt Filter Press dewaters flocculated sludge by sandwiching it between two tensioned, porous woven fabric belts travelling over a sequence of rollers:
Gravity Drainage Zone : Sludge pre-conditioned with cationic polymer is distributed onto the porous lower belt. In this zone, 50 % – 70 % 50\%\text{--}70\% 50% – 70% of free water drains away by simple gravity within 1 – 2 minutes 1\text{--}2\text{ minutes} 1 – 2 minutes , thickening the sludge from 3 % 3\% 3% to 6 % – 10 % 6\%\text{--}10\% 6% – 10% solids. Plastic chicanes (furrowing plows) continuously roll the sludge to open drainage channels. If poorly conditioned, sludge blinds the fabric and "washes out" past the sides.
Low-Pressure Wedge Zone : The upper and lower belts converge at a gentle angle. The sludge is subjected to gradual, low-pressure mechanical compression, forming a consolidated sludge "sandwich" without forcing liquid sludge out the edges.
High-Pressure Shear Zone : The sandwiched belts wrap in an S-pattern around a serpentine series of rollers of progressively decreasing diameters (large primary drum → \rightarrow → medium rollers → \rightarrow → small high-pressure rollers). As roller diameter ( r r r ) decreases, compressive pressure ( P = T / r P = T / r P = T / r , where T T T is belt tension) increases. Concurrently, the outer belt travels a slightly longer path than the inner belt, inducing high mechanical shear forces that rip open trapped water pockets. Dewatered cake discharges at doctor blades at 15 % – 25 % total solids 15\%\text{--}25\%\text{ total solids} 15% – 25% total solids .
Operational Variables :
Belt Speed : Faster belt speeds increase hydraulic throughput but reduce cake dryness and solids capture.
Belt Tension : Adjusted pneumatically/hydraulically ( 20 – 60 psi 20\text{--}60\text{ psi} 20 – 60 psi ); higher tension squeezes more water but risks blinding or belt extrusion.
Belt Wash Systems : High-pressure spray nozzles ( 80 – 120 psi 80\text{--}120\text{ psi} 80 – 120 psi ) continuously clean the return belts to prevent fabric blinding.
Solid Bowl Decanter Centrifuges
A decanter centrifuge dewaters sludge using centrifugal sedimentation acceleration:
Mechanical Structure : Comprises a horizontal, rapidly rotating cylindrical-conical steel bowl and an internal helical scroll conveyor. The bowl rotates at 1 , 500 – 3 , 500 RPM 1,500\text{--}3,500\text{ RPM} 1 , 500 – 3 , 500 RPM , generating a centrifugal field of 1 , 000 – 3 , 000 Gs 1,000\text{--}3,000\text{ Gs} 1 , 000 – 3 , 000 Gs (gravities).
Differential Speed ( Δ N \Delta N Δ N ) : The internal scroll conveyor rotates in the same direction as the outer bowl but at a slightly slower or faster speed, creating a differential speed ( Δ N \Delta N Δ N ) of 1 – 20 RPM 1\text{--}20\text{ RPM} 1 – 20 RPM driven by a planetary gearbox or backdrive motor.
Separation & Conveyance : Dense sludge solids are thrown against the inner bowl wall and conveyed by the scroll up the conical "beach" (drying deck) toward solids discharge ports, discharging at 20 % – 30 % solids 20\%\text{--}30\%\text{ solids} 20% – 30% solids . Clarified liquid ( centrate ) flows in the opposite direction, discharging over adjustable endplate weir plates.
Process Adjustments :
Pool Depth (Liquid Ring Depth) : Adjusted via eccentric weir plates. Deep pool increases clarification detention time (clearer centrate) but shortens beach drying length (wetter cake). Shallow pool maximizes beach exposure (drier cake) but increases centrate turbidity.
Differential Scroll Speed ( Δ N \Delta N Δ N ) : Lowering Δ N \Delta N Δ N increases solids residence time on the beach, producing a drier cake, but increases gearbox torque.
2. Polymer Conditioning Chemistry & Optimization
Bacterial cell surfaces and sludge particles carry net negative surface charges (zeta potential of − 10 to − 30 mV -10\text{ to } -30\text{ mV} − 10 to − 30 mV ) that cause particles to repel each other, keeping them in stable colloidal suspension.
Cationic Synthetic Polymers : Long-chain polyacrylamides containing positively charged quaternary ammonium functional groups are dosed into the sludge feed. The polymer destabilizes the colloids by charge neutralization and binds multiple flocs together through interparticle bridging , creating large, robust, fast-draining macro-flocs.
Polymer Solution Preparation & Aging : Concentrated liquid emulsion polymer must be diluted with clean water and subjected to high initial mixing shear to invert the emulsion, followed by a 30 – 60 minute 30\text{--}60\text{ minute} 30 – 60 minute low-shear aging / hydration period to allow long polymer chains to fully uncoil without shearing. Over-shearing with high-speed impellers fractures the polymer chains, destroying flocculation effectiveness.
3. Biosolids Standards: EPA Part 503 & Colorado Regulation 64
Colorado Regulation 64 (5 CCR 1002-64) establishes state requirements for the beneficial use of biosolids. Biosolids are classified based on Pathogen Reduction , Vector Attraction Reduction (VAR) , and Heavy Metal Concentrations . +-----------------------------------------------------------------------------------------+
- | BIOSOLIDS CLASSIFICATION & USE MATRIX |
- +-----------------------------------------------------------------------------------------+
- | Class Level | Pathogen Criteria | Permitted End Uses & Restrictions |
- +---------------+--------------------------------+----------------------------------------+
- | **Class A** | Pathogens below detectable | **Unrestricted Public Distribution**: |
- | **(EQ - | limits: | Bagged retail fertilizer, home gardens,|
- | Exceptional | • Fecal Coliform < 1,000 MPN/g | lawns, golf courses, city parks, and |
- | Quality)** | dry solids, OR | unrestricted agricultural application. |
- | | • Salmonella < 3 MPN / 4g | Zero site or harvesting restrictions. |
- | | dry solids. (PFRP required) | |
- +---------------+--------------------------------+----------------------------------------+
- | **Class B** | Significant pathogen reduction | **Restricted Agricultural / Forestry**:|
- | | • Fecal Coliform geometric | Strict site access restrictions, |
- | | mean < 2,000,000 MPN/g dry | mandatory grazing wait times (30 days),|
- | | solids (PSRP required). | crop harvesting delays (14-38 months), |
- | | | and mandatory setback buffer zones. |
- +-----------------------------------------------------------------------------------------+
- Processes to Further Reduce Pathogens (PFRP) for Class A
To achieve Class A status, sludge must satisfy one of the approved PFRP operational methods:
Composting : Within-vessel or static aerated pile maintained at ≥ 55 ∘ C \ge 55^\circ\text{C} ≥ 5 5 ∘ C ( 131 ∘ F 131^\circ\text{F} 13 1 ∘ F ) for 3 consecutive days ; or windrow composting maintained at ≥ 55 ∘ C \ge 55^\circ\text{C} ≥ 5 5 ∘ C for 15 consecutive days with at least 5 complete pile turnings .
Heat Drying : Biosolids dried with direct or indirect hot gases to reduce moisture to ≤ 10 % \le 10\% ≤ 10% , with particle temperatures exceeding 80 ∘ C 80^\circ\text{C} 8 0 ∘ C ( 176 ∘ F 176^\circ\text{F} 17 6 ∘ F ) .
Thermophilic Aerobic Digestion : Liquid sludge agitated and aerated at 55 ∘ C– 60 ∘ C 55^\circ\text{C}\text{--}60^\circ\text{C} 5 5 ∘ C – 6 0 ∘ C for at least 10 days mean cell residence time.
High-Temperature Pasteurization : Maintained at ≥ 70 ∘ C \ge 70^\circ\text{C} ≥ 7 0 ∘ C ( 158 ∘ F 158^\circ\text{F} 15 8 ∘ F ) for at least 30 continuous minutes .
Processes to Significantly Reduce Pathogens (PSRP) for Class B
Anaerobic Digestion : Digested for 15 days at 35 ∘ C– 55 ∘ C 15\text{ days at } 35^\circ\text{C}\text{--}55^\circ\text{C} 15 days at 3 5 ∘ C – 5 5 ∘ C or 60 days at 20 ∘ C 60\text{ days at } 20^\circ\text{C} 60 days at 2 0 ∘ C .
Aerobic Digestion : Digested for 40 days at 20 ∘ C 40\text{ days at } 20^\circ\text{C} 40 days at 2 0 ∘ C or 60 days at 15 ∘ C 60\text{ days at } 15^\circ\text{C} 60 days at 1 5 ∘ C .
Lime Stabilization : Sufficient lime added to raise pH to ≥ 12.0 for 2 hours \ge 12.0\text{ for 2 hours} ≥ 12.0 for 2 hours of contact.
Mandatory Colorado Regulation 64 Class B Site Restrictions
Livestock Grazing : Animals shall not graze on land for 30 days following application.
Food Crops : Crops with harvested parts touching the ground (melons, squash) shall not be harvested for 14 months ; crops with harvested parts below ground (carrots, potatoes) shall not be harvested for 20 to 38 months .
Public Access : High-exposure public land restricted for 1 year ; low-exposure land restricted for 30 days .
Setback Buffer Distances : Minimum of 500 feet from domestic drinking water wells; 100 feet from surface streams/rivers; 200 feet from occupied residential dwellings.
Vector Attraction Reduction (VAR) Options
Vectors (flies, mosquitoes, rodents) transmit pathogens from biosolids to humans. Facilities must document compliance with one of the 10 approved VAR Options :
Option 1 (Volatile Solids Reduction) : Achieve at least 38 % Volatile Solids Reduction (VSR) 38\%\text{ Volatile Solids Reduction (VSR)} 38% Volatile Solids Reduction (VSR) across anaerobic or aerobic digestion.
Option 4 (Specific Oxygen Uptake Rate / SOUR) : SOUR ≤ 1.5 mg O 2 / hr ⋅ g total solids \le 1.5\text{ mg } O_2 / \text{hr}\cdot\text{g total solids} ≤ 1.5 mg O 2 / hr ⋅ g total solids at 20 ∘ C 20^\circ\text{C} 2 0 ∘ C for aerobically digested sludge.
Option 6 (Alkaline Stabilization) : pH raised to ≥ 12.0 \ge 12.0 ≥ 12.0 for 2 hours 2\text{ hours} 2 hours and maintained at ≥ 11.5 \ge 11.5 ≥ 11.5 for an additional 22 hours 22\text{ hours} 22 hours without further lime addition.
Option 9 (Subsurface Injection) : Liquid biosolids injected below the soil surface within 8 hours of discharge with zero significant liquid remaining on the surface.
Option 10 (Soil Incorporation) : Biosolids applied to surface incorporated/plowed into soil within 6 hours .
Heavy Metal Limits (Regulation 64 / EPA Part 503)
Nine trace heavy metals are strictly regulated: Arsenic (As), Cadmium (Cd), Copper (Cu), Lead (Pb), Mercury (Hg), Molybdenum (Mo), Nickel (Ni), Selenium (Se), and Zinc (Zn) . Biosolids exceeding Ceiling Concentrations (Table 1) cannot be land applied under any circumstance. To qualify as Exceptional Quality (Class A EQ), biosolids must meet the strict monthly average Pollutant Concentrations (Table 3) .
4. Worked Dewatering & Polymer Calculation
A belt filter press dewaters 40 , 000 gallons/day 40,000\text{ gallons/day} 40 , 000 gallons/day of digested sludge at 3.0 % 3.0\% 3.0% total dry solids ( 0.03 0.03 0.03 ) . The dewatering press achieves a cake solids concentration of 20.0 % 20.0\% 20.0% dry solids ( 0.20 0.20 0.20 ) with a solids capture rate of 95.0 % 95.0\% 95.0% ( 0.95 0.95 0.95 ) . Liquid emulsion polymer is fed at a dosage of 18.0 lbs of active polymer per dry ton of sludge solids 18.0\text{ lbs of active polymer per dry ton of sludge solids} 18.0 lbs of active polymer per dry ton of sludge solids .
Step 1: Calculate Total Dry Sludge Solids Processed per Day Total Wet Sludge Mass = 40 , 000 gal × 8.34 lbs/gal = 333 , 600 lbs liquid sludge/day \text{Total Wet Sludge Mass} = 40,000\text{ gal} \times 8.34\text{ lbs/gal} = 333,600\text{ lbs liquid sludge/day} Total Wet Sludge Mass = 40 , 000 gal × 8.34 lbs/gal = 333 , 600 lbs liquid sludge/day Dry Solids Processed = 333 , 600 lbs × 0.03 = 10 , 008 lbs dry solids/day \text{Dry Solids Processed} = 333,600\text{ lbs} \times 0.03 = 10,008\text{ lbs dry solids/day} Dry Solids Processed = 333 , 600 lbs × 0.03 = 10 , 008 lbs dry solids/day Dry Tons Processed = 10 , 008 lbs/day 2 , 000 lbs/ton = 5.004 dry tons/day \text{Dry Tons Processed} = \frac{10,008\text{ lbs/day}}{2,000\text{ lbs/ton}} = 5.004\text{ dry tons/day} Dry Tons Processed = 2 , 000 lbs/ton 10 , 008 lbs/day = 5.004 dry tons/day
Step 2: Calculate Wet Cake Produced per Day Dry Solids Captured in Cake = 10 , 008 lbs × 0.95 = 9 , 507.6 lbs dry solids \text{Dry Solids Captured in Cake} = 10,008\text{ lbs} \times 0.95 = 9,507.6\text{ lbs dry solids} Dry Solids Captured in Cake = 10 , 008 lbs × 0.95 = 9 , 507.6 lbs dry solids Wet Cake Mass Produced = 9 , 507.6 lbs dry solids 0.20 cake solids concentration = 47 , 538 lbs wet cake/day \text{Wet Cake Mass Produced} = \frac{9,507.6\text{ lbs dry solids}}{0.20\text{ cake solids concentration}} = 47,538\text{ lbs wet cake/day} Wet Cake Mass Produced = 0.20 cake solids concentration 9 , 507.6 lbs dry solids = 47 , 538 lbs wet cake/day Wet Cake Volume = 47 , 538 lbs 2 , 000 lbs/ton = 23.77 wet tons cake/day \text{Wet Cake Volume} = \frac{47,538\text{ lbs}}{2,000\text{ lbs/ton}} = 23.77\text{ wet tons cake/day} Wet Cake Volume = 2 , 000 lbs/ton 47 , 538 lbs = 23.77 wet tons cake/day
Step 3: Calculate Daily Active Polymer Requirement Active Polymer Required = 5.004 dry tons/day × 18.0 lbs active / dry ton = 90.07 lbs active polymer/day \text{Active Polymer Required} = 5.004\text{ dry tons/day} \times 18.0\text{ lbs active / dry ton} = 90.07\text{ lbs active polymer/day} Active Polymer Required = 5.004 dry tons/day × 18.0 lbs active / dry ton = 90.07 lbs active polymer/day