Study guide
1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T)
Colorado Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: State Laws, Regulations & CCWP Certification
1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting
2 Chapter 2: Source Water & Drinking Water Treatment Processes
2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle
3 Chapter 3: Disinfection & Chemical Addition
3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices
4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance
4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management
5 Chapter 5: Wastewater Treatment Principles & Biological Processes
5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects
6 Chapter 6: Advanced Wastewater Treatment & Solids Management
6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84
7 Chapter 7: Water Distribution Systems
7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems
8 Chapter 8: Wastewater Collection Systems
8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment
9 Chapter 9: Pumps, Motors & Utility Mechanics
9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control
10 Chapter 10: Laboratory Analysis & Water Quality Monitoring
10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)
11 Chapter 11: Operator Mathematics & Applied Calculations
11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance
12 Chapter 12: Safety, Emergency Operations & Compliance
12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties
1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T)
Key Takeaways Explain This Topic AI
Applicants must hold a high school diploma or GED; substituting for it requires six additional months of qualifying experience plus 1.0 training unit in an approved entry-level course.
Regulation 100 section 100.14.5(j) requires prior certification in the class immediately below: Class C needs Class D or S, Class B needs Class C, Class A needs Class B, and the numbered distribution and collection classes follow the same pattern.
Minimum experience is 1 month for Class S, D, or 1; 2 years for Class C or 2; 3 years for Class B or 3; and 4 years for Class A or 4, with no minimum for Class T.
Education, military training, and training units may substitute for up to 50 percent of the experience requirement, with 30 semester hours or 45 quarter hours equal to one year and 30 training units equal to four months.
Certification by examination costs a $50 CCWP application fee plus a $104 PSI exam fee, the passing score is 70 percent, and a failed candidate may retest within the 100-day eligibility period.
Last updated: August 2026
The Colorado Certification Matrix
Colorado credentials are built so operators demonstrate both classroom knowledge and hands-on operational judgment. Under Regulation 100, section 100.14 , an applicant must satisfy education, experience, prior-certification, and regulatory-training criteria before CDPHE's contractor will approve them to sit for an examination.
Each discipline advances through four tiers, and the letter or number tracks the facility classification it authorizes:
- Water Treatment: Class D (entry) → Class C → Class B → Class A
- Domestic Wastewater Treatment: Class D → Class C → Class B → Class A
Industrial Wastewater Treatment: Class D → Class C → Class B → Class A (same letters as domestic — not Roman numerals)
- Water Distribution: Class 1 (entry) → Class 2 → Class 3 → Class 4
- Wastewater Collection: Class 1 → Class 2 → Class 3 → Class 4
- Hybrid small-system certificates: Class S water, Class S wastewater, and Class T
- The four eligibility gates
Section 100.14.5(c) states plainly that to qualify to sit for an examination an applicant must meet all four of the following:
Approved mandatory regulatory training (MRT) completed before the application is submitted. Each completion is valid for three years .
Minimum education requirements.
Minimum experience or cross-experience requirements.
Prior certification requirements.
Education
Applicants must be high school graduates or hold a GED . An applicant who lacks either may substitute experience and relevant training, but section 100.14.5(e)(ii) requires both an additional six months of qualifying experience and completion of 1.0 training unit in a course approved as a substitute for entry-level experience requirements.
Prior certification and experience
This is the single table most heavily tested on the Colorado regulatory items. Prior certification must be in the same certification category as the exam being applied for.
- Certification class Prior certification required Minimum experience
- Class T None No minimum experience requirement
- Class S, Class D, or Class 1 None 1 month
- Class C Class D or Class S 2 years
- Class 2 Class 1 or Class S 2 years
- Class B Class C 3 years
- Class 3 Class 2 3 years
- Class A Class B 4 years
- Class 4 Class 3 4 years
Two nuances trip people up. First, section 100.14.5(f)(vi) says the experience you rely on does not have to have been obtained at the level of the examination you are applying for — there is no rule requiring, say, "two years inside a Class B plant" before a Class A exam. The gate is the prior certificate , not where the hours were logged. Second, for Class D, Class 1, Class S, and Class T, section 100.14.5(k) allows the one-month experience requirement to be met either under the supervision of a certified ORC or through successful completion of an approved training course or course of study — but any course used that way may not also be used to renew that same certificate.
How experience is counted
Section 100.14.5(f) governs the arithmetic:
No more than one year of experience is credited for any one calendar year, regardless of how many facilities you work at.
At facilities that do not need a full-time operator, an operator working less than half time is credited half-time experience; half time or more is credited as full time.
Time across multiple facilities is aggregated when deciding full-time versus half-time credit.
Seasonal facility experience is credited only for the portion of the year the facility operates.
The experience cut-off date is the date the application is submitted.
Section 100.14.5(g) directs reviewers to weigh whether the work required technical knowledge, whether it was actual on-site operating experience affecting water quality or quantity, and whether it involved responsible charge. Section 100.14.5(h) bars double-counting : experience or training already credited toward one requirement cannot be credited again toward another.
Substituting education and cross-experience +-------------------------------------------------------------------------+
- | THE 50 PERCENT RULE (Sections 100.14.6(a) and (c)) |
- +-------------------------------------------------------------------------+
- | At least FIFTY PERCENT of any experience requirement must be met by |
- | actual on-site operating experience -- EXCEPT that Class D, Class 1, |
- | and Class S applicants may satisfy the experience requirement entirely |
- | with academic credits or training units under 100.14.5(k). |
- | |
- | Class C / Class 2 (24 months): max 12 months substituted |
- | Class B / Class 3 (36 months): max 18 months substituted |
- | Class A / Class 4 (48 months): max 24 months substituted |
- +-------------------------------------------------------------------------+
Academic credit conversion (section 100.14.6(a)(i)):
- 15 semester hours = one-half academic year = 6 months of experience
- 15 quarter hours = one-third academic year = 4 months of experience
- 30 semester hours or 45 quarter hours = one academic year = 1 year of experience
- 300 contact hours, or 30 training units , = 15 quarter hours = 4 months of experience
That last line matters: a training unit is 10 contact hours, so 30 TUs equals four months , which works out to 7.5 TUs per month of experience credit — not one month for 3 TUs.
Military training (section 100.14.6(a)(ii)): relevant military specialty training may cover up to 50 percent of the requirement; one week of training equals 40 contact hours, and 240 contact hours equals 15 semester hours, that is, 6 months of experience.
Field of study (section 100.14.6(a)(iii)): a technically oriented program the Board finds directly relevant to water or wastewater operation may cover up to 50 percent ; a degree program in any field of study may cover up to 25 percent . Credit is granted by the number of academic years the program requires, converted with the table above.
Cross-experience (section 100.14.6(c)): water treatment experience may substitute for up to 50 percent of wastewater treatment experience and vice versa; distribution experience may substitute for up to 50 percent of collection experience and vice versa. Cross-experience is available only for Class C, B, and A and Class 2, 3, and 4 applications, and at least 50 percent of the requirement must still be on-site experience in the category being applied for.
Worked eligibility evaluation
An operator holding a valid Class B water treatment certificate applies for the Class A water treatment exam. Records show 30 months of full-time operating experience and a completed associate degree of 62 semester hours in water quality technology.
Prior certification: Class A requires Class B. Satisfied.
Experience required: 48 months.
Education credit: 62 semester hours ÷ 30 semester hours per year = 2.06 years, so 24 months of credit is available on the conversion table.
The 50 percent cap: 48 months × 0.50 = 24 months maximum substitution. The degree credit is capped at exactly 24 months.
Total: 30 months on-site + 24 months education = 54 months , but at least 24 months must be on-site and the applicant has 30. Both tests pass.
Conclusion: the applicant is eligible to sit for the Class A water treatment examination.
Application, examination, and retesting
Create a CCWP Portal account at portal.coloradocwp.com and obtain an operator ID number . Training providers upload training units against that ID.
Enter education, experience, and MRT records in the portal and obtain a green check on every eligibility criterion.
Initiate the application and pay the $50 application and administration fee (section 100.17.1). Review takes roughly 10 business days.
On approval, create or log in to a PSI account and schedule the exam, then pay the $104 exam fee to PSI (section 100.17.2). You may test at a PSI test center or by remote proctoring if your equipment qualifies.
Sit the WPI standardized exam : 100 scored multiple-choice questions, up to 10 unscored pre-test items, a three-hour limit, and a formula and conversion table supplied on screen.
Scoring. Section 100.14.5(c) sets the minimum passing score at 70 percent . Section 100.15.1(d) entitles examinees to an analysis of performance showing the level of knowledge demonstrated for each topic tested , which is the most useful diagnostic available if you must retake.
Retesting. Section 100.15.1(e) allows an applicant who fails to retest within the 100-day eligibility period , and no additional application and administration fee is charged during that window — although a new exam fee applies to each attempt. There is no mandatory 30-day waiting period in Regulation 100.
Certificates from other entities. Section 100.14.5(d) lets the Board's contractor issue a certificate without examination, case by case, to an applicant in good standing elsewhere who has passed a Colorado-approved exam for that category and class with a minimum pass rate of 70 percent, meets Colorado education and experience minimums, earned the qualifying experience in the jurisdiction where they hold the certificate, and completed Colorado's MRT. The application fee for this route is $150 .