Study guide
10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring
Colorado Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: State Laws, Regulations & CCWP Certification
1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting
2 Chapter 2: Source Water & Drinking Water Treatment Processes
2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle
3 Chapter 3: Disinfection & Chemical Addition
3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices
4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance
4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management
5 Chapter 5: Wastewater Treatment Principles & Biological Processes
5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects
6 Chapter 6: Advanced Wastewater Treatment & Solids Management
6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84
7 Chapter 7: Water Distribution Systems
7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems
8 Chapter 8: Wastewater Collection Systems
8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment
9 Chapter 9: Pumps, Motors & Utility Mechanics
9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control
10 Chapter 10: Laboratory Analysis & Water Quality Monitoring
10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)
11 Chapter 11: Operator Mathematics & Applied Calculations
11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance
12 Chapter 12: Safety, Emergency Operations & Compliance
12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties
10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring
Key Takeaways Explain This Topic AI
Bench-scale jar testing simulates plant-scale rapid mix, tapered flocculation, and sedimentation to establish optimum coagulant dosages, polymer aids, and process pH.
Standard jar testing employs 2-liter square B-Ker jars to prevent liquid vortexing and utilizes a tapered flocculation profile (e.g., 50 RPM, 30 RPM, 15 RPM) following a 1-minute rapid mix.
Supernatant evaluation requires sampling 2 cm below the water surface, measuring settled turbidity, residual alkalinity, pH, and Natural Organic Matter (NOM/UV-254) removal.
Coagulant overdosing causes charge reversal, colloidal restabilization, high residual dissolved metals, excessive chemical sludge volume, and severe alkalinity depletion.
Streaming Current Detectors (SCD) provide real-time electrokinetic monitoring of colloidal charge in rapid-mix effluent to automate chemical feed pacing, calibrated against jar tests.
Last updated: August 2026
Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring
Surface water sources throughout Colorado exhibit dramatic seasonal water quality swings—ranging from pristine, near-freezing winter mountain runoff with low turbidity ( < 1.0 NTU < 1.0\text{ NTU} < 1.0 NTU ) and low alkalinity, to violent spring snowmelts and summer flash storms carrying extreme suspended sediment loads ( > 500 NTU > 500\text{ NTU} > 500 NTU ) and elevated Total Organic Carbon (TOC). Bench-scale jar testing and online Streaming Current Monitoring are the two primary tools operators utilize to optimize chemical coagulation, maintain finished water clarity, and ensure compliance with the Disinfectants and Disinfection Byproducts Rule (DBPR) .
1. Purpose & Physical Chemistry of Coagulation Optimization
Naturally occurring suspended colloids (clays, silts, organic humic acids, and microorganisms) carry net negative surface electrical charges . These like charges generate mutual electrostatic repulsive forces, preventing particles from aggregating and keeping them in stable suspension indefinitely. [ Negatively Charged Colloids (Zeta Potential: -15 to -30 mV) ]
- | (Electrostatic Repulsion Prevents Settling)
- v
- +-------------------------------------------------------------------+
- | Primary Coagulant Injection (Alum Al3+, Ferric Fe3+, or PAC) |
- +-------------------------------------------------------------------+
- |
- +---------------------------------------+---------------------------------------+
- | |
- v (Charge Neutralization) v (Sweep-Floc Enmeshment)
- [ Trivalent Cations Neutralize Negative Charges ] [ Insoluble Metal Hydroxide Precipitates Al(OH)3 / Fe(OH)3 ]
- [ Zeta Potential Approaches 0 mV ] [ Physically Enmesh & Sweep Colloidal Particles Downward ]
- | |
- +---------------------------------------+---------------------------------------+
- v
- [ Rapid Floc Growth & Aggregation ]
- [ Dense, Rapidly Settling Macrofloc]
- Primary Coagulation Mechanisms
Charge Neutralization: Positively charged trivalent metal cations ( Al 3 + \text{Al}^{3+} Al 3 + , Fe 3 + \text{Fe}^{3+} Fe 3 + ) or cationic polymers adsorb directly onto the negatively charged colloidal surfaces, compressing the electrical double layer and reducing the zeta potential from − 15 to − 30 mV -15\text{ to } -30\text{ mV} − 15 to − 30 mV toward zero (the isoelectric point). Once repulsions are neutralized, van der Waals attractive forces pull particles together into microflocs.
Sweep-Floc Enmeshment: At coagulant dosages exceeding the solubility limit of metal hydroxides (typical at pH 6.5 – 8.0 \text{pH } 6.5\text{--}8.0 pH 6.5 – 8.0 ), amorphous, sticky precipitates of aluminum hydroxide ( Al(OH) 3 \text{Al(OH)}_3 Al(OH) 3 ) or ferric hydroxide ( Fe(OH) 3 \text{Fe(OH)}_3 Fe(OH) 3 ) precipitate out of solution, physically entrapping and sweeping suspended colloids downward.
Interparticle Polymer Bridging: High-molecular-weight long-chain synthetic polymers bind simultaneously to multiple colloidal particles, building large, tough macroflocs that resist hydraulic shear.
Primary Objectives of Jar Testing
Establish the optimum primary coagulant dosage (Alum Al 2 ( SO 4 ) 3 ⋅ 14 H 2 O \text{Al}_2(\text{SO}_4)_3\cdot 14\text{H}_2\text{O} Al 2 ( SO 4 ) 3 ⋅ 14 H 2 O , Ferric Chloride FeCl 3 \text{FeCl}_3 FeCl 3 , Polyaluminum Chloride PAC).
Determine the necessity, type, and dosage of coagulant aids or filter aids (cationic, anionic, or non-ionic polymers).
Identify the optimum coagulation pH window (typically pH 5.8 to 6.8 for alum; pH 5.0 to 8.5 for ferric salts).
Evaluate chemical addition sequencing (e.g., adding lime/caustic before vs. after coagulant; polymer injection delay timing).
Determine Total Organic Carbon (TOC) / DBP precursor removal efficiency under EPA Stage 1 DBPR Enhanced Coagulation requirements.
Loading diagram... Bench-Scale Jar Testing & Coagulation Optimization Protocol
- 2. Standard Jar Test Equipment & Chemical Stock Preparation
- Jar Test Apparatus Specifications
Gang-Stirrer Mechanism: A 6-paddle synchronized drive unit with an electronic digital RPM readout and programmable multi-step timer (such as a Phipps & Bird jar tester).
2-Liter Square B-Ker Jars: Square acrylic or glass jars are vastly superior to round laboratory beakers. The square corners act as internal baffles , eliminating bulk fluid vortexing and ensuring uniform energy dissipation ( G G G -values) that accurately models full-scale hydraulic rapid mix and flocculation basins.
Subsurface Sampling Ports: Fixed sampling stopcocks positioned 2.0 cm 2.0\text{ cm} 2.0 cm below the water surface (approx. 10 cm 10\text{ cm} 10 cm above the container bottom) allow operators to withdraw supernatant without disturbing settled floc.
Preparing Liquid Chemical Working Stocks
To accurately dose milligram-per-liter concentrations into bench-top jars, operators prepare fresh working stock solutions from commercial treatment chemicals:
1.0% Working Stock Solution ( 10,000 mg/L 10{,}000\text{ mg/L} 10 , 000 mg/L ): Dissolve 10.0 g 10.0\text{ g} 10.0 g of dry chemical (or 10.0 mL 10.0\text{ mL} 10.0 mL of liquid chemical) in deionized water and dilute to 1,000 mL 1{,}000\text{ mL} 1 , 000 mL .
1.0 mL 1.0\text{ mL} 1.0 mL of 1.0 % stock 1.0\%\text{ stock} 1.0% stock in a 1.0 L 1.0\text{ L} 1.0 L jar = 10.0 mg/L 10.0\text{ mg/L} 10.0 mg/L dosage .
1.0 mL 1.0\text{ mL} 1.0 mL of 1.0 % stock 1.0\%\text{ stock} 1.0% stock in a 2.0 L 2.0\text{ L} 2.0 L jar = 5.0 mg/L 5.0\text{ mg/L} 5.0 mg/L dosage .
0.1% Working Stock Solution ( 1,000 mg/L 1{,}000\text{ mg/L} 1 , 000 mg/L ): Used for low-dose polymer aids ( 1.0 mL 1.0\text{ mL} 1.0 mL in 2.0 L = 0.50 mg/L 2.0\text{ L} = 0.50\text{ mg/L} 2.0 L = 0.50 mg/L ). Polymer working stocks must be prepared daily to prevent polymer strand degradation. Chemical Dose (mg/L) = Stock Volume Added (mL) × Stock Concentration (mg/mL) Jar Water Volume (L) \text{Chemical Dose (mg/L)} = \frac{\text{Stock Volume Added (mL)} \times \text{Stock Concentration (mg/mL)}}{\text{Jar Water Volume (L)}} Chemical Dose (mg/L) = Jar Water Volume (L) Stock Volume Added (mL) × Stock Concentration (mg/mL)
Worked Example 9.5.1: Dosing Calculation for 2-Liter Jar Test
An operator prepares a 1.0 % 1.0\% 1.0% liquid alum working stock solution ( 10.0 mg/mL 10.0\text{ mg/mL} 10.0 mg/mL ). What volume of stock solution must be pipetted into a 2.0 L 2.0\text{ L} 2.0 L square B-Ker jar to achieve an alum dosage of 35.0 mg/L 35.0\text{ mg/L} 35.0 mg/L ?
Step 1: Calculate total mass of alum required: Required Mass = 35.0 mg/L × 2.0 L = 70.0 mg \text{Required Mass} = 35.0\text{ mg/L} \times 2.0\text{ L} = 70.0\text{ mg} Required Mass = 35.0 mg/L × 2.0 L = 70.0 mg
Step 2: Calculate volume of 1.0% working stock ( 10.0 mg/mL 10.0\text{ mg/mL} 10.0 mg/mL ): Stock Volume = 70.0 mg 10.0 mg/mL = 7.0 mL \text{Stock Volume} = \frac{70.0\text{ mg}}{10.0\text{ mg/mL}} = 7.0\text{ mL} Stock Volume = 10.0 mg/mL 70.0 mg = 7.0 mL
3. Step-by-Step Jar Testing Protocol
Raw Water Sampling & Characterization: Collect a fresh 15 – 20 L 15\text{--}20\text{ L} 15 – 20 L grab sample of raw surface water. Measure and record baseline water quality parameters: temperature ( ∘ C ^\circ\text{C} ∘ C ), turbidity (NTU), pH, total alkalinity ( mg/L as CaCO 3 \text{mg/L as }\text{CaCO}_3 mg/L as CaCO 3 ), and UV-254 absorbance ( cm − 1 \text{cm}^{-1} cm − 1 ). Do not allow the sample to warm up to room temperature , as temperature directly alters water viscosity and coagulation kinetics.
Rapid Mix Stage: Fill six 2.0 L 2.0\text{ L} 2.0 L square jars with exactly 2.0 L 2.0\text{ L} 2.0 L of raw water. Lower paddles and start rapid mix at 100 to 120 RPM (velocity gradient G ≈ 300 – 1000 s − 1 G \approx 300\text{--}1000\text{ s}^{-1} G ≈ 300 – 1000 s − 1 ). Simultaneously inject the incremental coagulant doses into jars 1 through 6 using calibrated syringes (e.g., Jar 1: Control 0 mg/L 0\text{ mg/L} 0 mg/L ; Jar 2: 10 mg/L 10\text{ mg/L} 10 mg/L ; Jar 3: 20 mg/L 20\text{ mg/L} 20 mg/L ; Jar 4: 30 mg/L 30\text{ mg/L} 30 mg/L ; Jar 5: 40 mg/L 40\text{ mg/L} 40 mg/L ; Jar 6: 50 mg/L 50\text{ mg/L} 50 mg/L ). Maintain rapid mix for exactly 1 minute (60 seconds) .
Tapered Flocculation Stage: Immediately reduce paddle speeds to simulate the diminishing velocity gradients of plant flocculation stages:
Step 1 (High Energy): 50 RPM 50\text{ RPM} 50 RPM for 5 minutes (promotes initial microfloc particle collisions).
Step 2 (Medium Energy): 30 RPM 30\text{ RPM} 30 RPM for 10 minutes (builds macrofloc bridges).
Step 3 (Low Energy): 15 RPM 15\text{ RPM} 15 RPM for 5 minutes (floc maturation and compaction without hydraulic shear).
Total Flocculation Time: 20 minutes 20\text{ minutes} 20 minutes .
Quiescent Settling Stage: Stop the motor, raise the paddles smoothly above the water level without agitating the vessels, and allow quiescent settling for 15 to 30 minutes .
Observation & Supernatant Sampling:
Visual Observations: Note the time of initial pin-floc formation (typically < 1 – 2 minutes < 1\text{--}2\text{ minutes} < 1 – 2 minutes for ideal doses), floc size (fine, pin-point, medium, or large feathery floc), and settling velocity (rate of floc blanket drop in inches per minute; > 2.0 – 4.0 in/min > 2.0\text{--}4.0\text{ in/min} > 2.0 – 4.0 in/min indicates excellent settling).
Supernatant Analytical Testing: Open the sampling stopcock ( 2.0 cm 2.0\text{ cm} 2.0 cm sub-surface) and discard the first 20 mL 20\text{ mL} 20 mL line purge. Collect 150 mL 150\text{ mL} 150 mL of supernatant and measure settled turbidity (NTU), residual pH, residual alkalinity, and UV-254 absorbance.
- 4. Interpreting Results & The Risks of Overdosing Supernatant Turbidity (NTU)
- ^
- | Underdosing Zone Optimum Dosing Zone Overdosing / Restabilization Zone
- | (Incomplete Destabilization)| (Charge Neutralization) | (Charge Reversal & Metal Precipitate Rise)
- |
- | \ /
- | \ /
- | \ /
- | \_________________________________________________/
- +--------------------------------------------------------------------------------------------->
- 0 10 20 30 40 50 60 70 80 90 100 Coagulant Dose (mg/L)
- [ Optimum Dose: 30-40 mg/L ]
- Identifying the True Optimum Coagulant Dose
The optimum coagulant dosage is the lowest chemical dose that:
Consistently achieves target settled water turbidity (typically ≤ 1.0 – 2.0 NTU \le 1.0\text{--}2.0\text{ NTU} ≤ 1.0 – 2.0 NTU , ensuring finished filtered water will meet the ≤ 0.30 NTU \le 0.30\text{ NTU} ≤ 0.30 NTU standard);
Produces dense, rapidly settling floc ( > 2 in/min > 2\text{ in/min} > 2 in/min ) within the allocated basin detention time;
Satisfies mandatory TOC removal requirements under EPA Stage 1 DBPR Enhanced Coagulation; and
Leaves adequate buffering alkalinity in the finished water (minimum ≥ 20 – 30 mg/L as CaCO 3 \ge 20\text{--}30\text{ mg/L as }\text{CaCO}_3 ≥ 20 – 30 mg/L as CaCO 3 ) to prevent corrosive finished water.
Consequences of Coagulant Overdosing
Charge Reversal & Colloidal Restabilization: Excess positive coagulant cations saturate colloidal surfaces, reversing particle charge from negative to positive. Particles re-disperse, causing settled turbidity to rise sharply.
Alkalinity Depletion & pH Crash: Every 1.0 mg/L 1.0\text{ mg/L} 1.0 mg/L of commercial alum consumes approximately 0.50 mg/L 0.50\text{ mg/L} 0.50 mg/L of natural alkalinity (as CaCO 3 \text{CaCO}_3 CaCO 3 ). Severe overdosing consumes all buffering capacity, dropping process pH below 5.5 5.5 5.5 .
Dissolved Metal Breakthrough: At pH < 5.8 \text{pH } < 5.8 pH < 5.8 , aluminum solubility increases exponentially, passing soluble aluminum through media filters into the distribution system (causing post-precipitation turbidity, consumer complaints, and water heater scaling).
Excessive Sludge Volume: Generates massive volumes of gelatinous, difficult-to-dewater metal hydroxide sludge, overwhelming solids handling facilities.
5. Streaming Current Detectors (SCD / SCM) for Online Control
While bench jar testing provides vital process optimization data, it is a batch test that cannot respond instantaneously to sudden raw water flash-turbidity events. An online Streaming Current Detector (SCD) (or Streaming Current Monitor, SCM) provides continuous, real-time electrokinetic measurement of colloidal charge immediately downstream of chemical injection. [ Sample Water from Rapid Mix Effluent ]
- |
- v
- +-----------------------------------------+
- | SCD Annular Cylinder / Sample Chamber |
- | |
- | +-----------------------------------+ |
- | | Reciprocating Piston (Oscillating)| |
- | +-----------------------------------+ |
- | |
- | Electrostatic Counter-Ions Sheared Off |
- | From Cylinder Wall During Fluid Motion |
- +-----------------------------------------+
- |
- v
- [ Electrodes Capture Displaced Charges ]
- |
- v (Alternating Current Signal)
- [ Microprocessor Amplifies & Rectifies ]
- |
- v
- [ Digital Display: Streaming Current Units (SCU) ]
- |
- v (4-20 mA Feedback Loop)
- [ Coagulant Chemical Metering Pump Adjustment ]
- Operating Principle of the Streaming Current Detector
Sample water from the rapid mix basin effluent is continuously pumped through the SCD sensing chamber.
Negatively charged colloidal particles temporarily adhere to the stationary walls of an annular Teflon cylinder.
A motorized Teflon piston reciprocates up and down inside the cylinder at a high frequency ( 4 to 5 cycles/second 4\text{ to } 5\text{ cycles/second} 4 to 5 cycles/second ). As the piston moves, it creates high fluid shear velocities along the cylinder walls, stripping mobile positive counter-ions away from the adsorbed colloids.
This continuous displacement of electrical charges generates a minute alternating electrical current (streaming current, microamperes) between two electrodes located at opposite ends of the cylinder.
The instrument amplifies and rectifies this signal, displaying a dimensionless output in Streaming Current Units (SCU) (typically spanning − 100 to + 100 SCU -100\text{ to } +100\text{ SCU} − 100 to + 100 SCU ).
Closed-Loop Chemical Feed Control & Calibration
Direct Correlation with Zeta Potential: Streaming current is directly proportional to the zeta potential of coagulated water. Negative SCU readings indicate underdosing (incomplete charge neutralization), while positive SCU readings indicate overdosing (charge reversal).
Automated Feedback Control: The SCD output ( 4 – 20 mA 4\text{--}20\text{ mA} 4 – 20 mA ) interfaces directly with the plant supervisory control and data acquisition ( SCADA ) system and coagulant chemical metering pumps. If raw water turbidity spikes, the streaming current drops negative, prompting the PID controller to automatically increase coagulant pump speed until the process returns to its established setpoint.
Calibration Against Jar Tests: The SCD is an empirical indicator, not an absolute meter. Operators must establish the target SCD setpoint by conducting a bench-scale jar test , determining the optimal dose, and setting the SCD controller to maintain the streaming current value produced by that optimal dose.