Study guide

11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI)

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI)

Key Takeaways Explain This Topic AI

The Food-to-Microorganism (F/M) ratio evaluates biological organic loading: F/M = (lbs BOD applied/day) / (lbs MLVSS under aeration), with typical conventional activated sludge operating between 0.2 to 0.5 day⁻¹.

Mean Cell Residence Time (MCRT or SRT) represents the average duration in days that biological solids remain in the system: MCRT = Total System MLSS (lbs) / (Daily WAS MLSS lbs + Daily Effluent TSS lbs).

To establish a target MCRT, operators calculate required Waste Activated Sludge (WAS) mass and convert it into daily wasting flow: Q_WAS (MGD) = WAS Demand (lbs/day) / (WAS_TSS mg/L × 8.34).

Sludge Volume Index (SVI) characterizes mixed liquor settleability: SVI (mL/g) = (Settled Sludge Volume in 30 min in mL/L × 1,000) / MLSS (mg/L).

An SVI between 80 to 150 mL/g signifies good settling and compactibility, while values above 150 mL/g indicate filamentous bulking and values below 80 mL/g indicate fast-settling pin floc.

Last updated: August 2026

Biological Process Control & Activated Sludge Stoichiometry

In the activated sludge process, certified wastewater operators control a living biological ecosystem. Heterotrophic and autotrophic bacteria consume dissolved organic matter (measured as Biochemical Oxygen Demand, BOD ) and nutrients (ammonia nitrogen and phosphorus). To maintain process stability, achieve nitrification, and prevent solids loss in secondary clarifiers, operators calculate and regulate three foundational process control parameters: the Food-to-Microorganism (F/M) ratio , the Mean Cell Residence Time (MCRT) (or Solids Retention Time, SRT), and the Sludge Volume Index (SVI) .

The Food-to-Microorganism (F/M) Ratio

The Food-to-Microorganism (F/M) ratio quantifies the ratio of organic food entering the aeration basin each day relative to the mass of active microorganisms maintained under aeration: F / M = Food (lbs BOD/day applied) Microorganisms (lbs MLVSS under aeration) \mathbf{F/M = \frac{\text{Food (lbs BOD/day applied)}}{\text{Microorganisms (lbs MLVSS under aeration)}}} F/M = Microorganisms (lbs MLVSS under aeration) Food (lbs BOD/day applied) ​ F / M = Influent Flow (MGD) × Primary Effluent BOD (mg/L) × 8.34 lbs/gal Aeration Basin Volume (MG) × MLVSS (mg/L) × 8.34 lbs/gal = Q × BOD V aer × MLVSS \mathbf{F/M = \frac{\text{Influent Flow (MGD)} \times \text{Primary Effluent BOD (mg/L)} \times 8.34\text{ lbs/gal}}{\text{Aeration Basin Volume (MG)} \times \text{MLVSS (mg/L)} \times 8.34\text{ lbs/gal}} = \frac{Q \times \text{BOD}}{V_{\text{aer}} \times \text{MLVSS}}} F/M = Aeration Basin Volume (MG) × MLVSS (mg/L) × 8.34 lbs/gal Influent Flow (MGD) × Primary Effluent BOD (mg/L) × 8.34 lbs/gal ​ = V aer ​ × MLVSS Q × BOD ​

Why MLVSS is Used: While Mixed Liquor Suspended Solids ( M L S S MLSS M L SS ) measures all suspended solids in the aeration basin, only the volatile fraction— Mixed Liquor Volatile Suspended Solids ( M L V S S MLVSS M L V SS ) —represents living biological mass. In municipal wastewater plants, M L V S S MLVSS M L V SS typically comprises 70 % 70\% 70% to 85 % 85\% 85% of total M L S S MLSS M L SS . +-----------------------------------------------------------------------------------------+

  • | ACTIVATED SLUDGE PROCESS MODES & OPERATING RANGES |
  • +-----------------------------------------------------------------------------------------+
  • | Process Mode | Typical F/M Ratio (day⁻¹) | Typical MCRT / Sludge Age (days)|
  • +---------------------------+---------------------------+---------------------------------+
  • | Extended Aeration / Oxidation Ditch | 0.05 to 0.15 | 15 to 30 days (low wasting) |
  • | Conventional Activated Sludge | 0.20 to 0.50 | 5 to 15 days (nitrifying: 10-20)|
  • | High-Rate Activated Sludge | 0.50 to 1.50 | 1 to 4 days (non-nitrifying) |
  • | Contact Stabilization | 0.20 to 0.60 | 5 to 10 days |
  • +-----------------------------------------------------------------------------------------+
  • Operational Implications of F/M Imbalance

High F/M Ratio ( > 0.5 day − 1 >0.5\text{ day}^{-1} > 0.5 day − 1 in conventional): Microorganisms have excess food relative to biomass. Bacteria reproduce rapidly in the log-growth phase, producing excessive extracellular slime, un-flocculated "straggler floc," turbid effluent, and high oxygen demand.

Low F/M Ratio ( < 0.2 day − 1 <0.2\text{ day}^{-1} < 0.2 day − 1 in conventional): Microorganisms enter the endogenous respiration (starvation) phase. Cells auto-oxidize, producing small, dense, easily shearable "pin floc" and elevated effluent turbidity with low BOD.

Mean Cell Residence Time (MCRT) & Solids Retention Time (SRT)

Mean Cell Residence Time (MCRT) —also termed Solids Retention Time (SRT) or Sludge Age —is the average time, in days, that a biological cell remains within the activated sludge system before being wasted or lost in the effluent: M C R T ( days ) = Total MLSS Inventory in System (lbs) Total Solids Lost per Day (lbs/day) = Aeration Basin MLSS (lbs) WAS TSS (lbs/day) + Effluent TSS (lbs/day) \mathbf{MCRT (\text{days}) = \frac{\text{Total MLSS Inventory in System (lbs)}}{\text{Total Solids Lost per Day (lbs/day)}} = \frac{\text{Aeration Basin MLSS (lbs)}}{\text{WAS TSS (lbs/day)} + \text{Effluent TSS (lbs/day)}}} MCRT ( days ) = Total Solids Lost per Day (lbs/day) Total MLSS Inventory in System (lbs) ​ = WAS TSS (lbs/day) + Effluent TSS (lbs/day) Aeration Basin MLSS (lbs) ​ M C R T = V aer ( MG ) × MLSS (mg/L) × 8.34 [ Q WAS ( MGD ) × WAS TSS ( mg/L ) × 8.34 ] + [ Q eff ( MGD ) × Eff TSS ( mg/L ) × 8.34 ] \mathbf{MCRT = \frac{V_{\text{aer}} (\text{MG}) \times \text{MLSS (mg/L)} \times 8.34}{[Q_{\text{WAS}} (\text{MGD}) \times \text{WAS}_{\text{TSS}} (\text{mg/L}) \times 8.34] + [Q_{\text{eff}} (\text{MGD}) \times \text{Eff}_{\text{TSS}} (\text{mg/L}) \times 8.34]}} MCRT = [ Q WAS ​ ( MGD ) × WAS TSS ​ ( mg/L ) × 8.34 ] + [ Q eff ​ ( MGD ) × Eff TSS ​ ( mg/L ) × 8.34 ] V aer ​ ( MG ) × MLSS (mg/L) × 8.34 ​

(Note: If clarifier solids inventory is included per specific exam problem instructions, add Clarifier Volume × \times × Clarifier Core TSS × 8.34 \times 8.34 × 8.34 to the numerator).

Calculating Target Waste Activated Sludge (WAS) Pumping Rate

To maintain a designated target MCRT, the operator rearranges the formula to solve for the required daily Waste Activated Sludge ( W A S WAS W A S ) mass and volumetric pumping rate ( Q WAS Q_{\text{WAS}} Q WAS ​ ): Target Daily Solids Loss (lbs/day) = Total System MLSS (lbs) Target MCRT (days) \text{Target Daily Solids Loss (lbs/day)} = \frac{\text{Total System MLSS (lbs)}}{\text{Target MCRT (days)}} Target Daily Solids Loss (lbs/day) = Target MCRT (days) Total System MLSS (lbs) ​ Required Daily WAS Mass (lbs/day) = Target Daily Solids Loss (lbs/day) − Effluent TSS Loss (lbs/day) \text{Required Daily WAS Mass (lbs/day)} = \text{Target Daily Solids Loss (lbs/day)} - \text{Effluent TSS Loss (lbs/day)} Required Daily WAS Mass (lbs/day) = Target Daily Solids Loss (lbs/day) − Effluent TSS Loss (lbs/day) Q WAS ( MGD ) = Required Daily WAS Mass (lbs/day) WAS Concentration (mg/L) × 8.34 lbs/gal = Required WAS (lbs/day) WAS TSS × 8.34 \mathbf{Q_{\text{WAS}} (\text{MGD}) = \frac{\text{Required Daily WAS Mass (lbs/day)}}{\text{WAS Concentration (mg/L)} \times 8.34\text{ lbs/gal}} = \frac{\text{Required WAS (lbs/day)}}{\text{WAS}_{\text{TSS}} \times 8.34}} Q WAS ​ ( MGD ) = WAS Concentration (mg/L) × 8.34 lbs/gal Required Daily WAS Mass (lbs/day) ​ = WAS TSS ​ × 8.34 Required WAS (lbs/day) ​ WAS Pumping Rate (gpm) = Q WAS ( MGD ) × 1 , 000 , 000 gal/MG 1 , 440 min/day \text{WAS Pumping Rate (gpm)} = \frac{Q_{\text{WAS}} (\text{MGD}) \times 1,000,000\text{ gal/MG}}{1,440\text{ min/day}} WAS Pumping Rate (gpm) = 1 , 440 min/day Q WAS ​ ( MGD ) × 1 , 000 , 000 gal/MG ​

Colorado Temperature Factor: In Colorado's cold winter climate, wastewater temperatures drop below 10 ∘ C 10^\circ\text{C} 1 0 ∘ C . Because nitrifying autotrophs ( Nitrosomonas and Nitrobacter ) exhibit suppressed metabolic kinetics at low temperatures, operators must increase MCRT (often to 15–25 days) to retain adequate nitrifiers and maintain permit compliance for ammonia ( N H 3 -N NH_3\text{-N} N H 3 ​ -N ).

Sludge Volume Index (SVI) & Settleability Testing

The Sludge Volume Index (SVI) is a standard empirical laboratory indicator that defines the settling and compaction characteristics of mixed liquor suspended solids. It represents the volume in milliliters occupied by one gram of mixed liquor solids after 30 minutes of quiescent settling in a 1 , 000 mL 1,000\text{ mL} 1 , 000 mL settleometer cylinder: S V I ( mL/g ) = Settled Sludge Volume in 30 minutes (mL/L) × 1 , 000 mg/g Aeration MLSS Concentration (mg/L) = S S V 30 × 1 , 000 MLSS \mathbf{SVI (\text{mL/g}) = \frac{\text{Settled Sludge Volume in 30 minutes (mL/L)} \times 1,000\text{ mg/g}}{\text{Aeration MLSS Concentration (mg/L)}} = \frac{SSV_{30} \times 1,000}{\text{MLSS}}} SVI ( mL/g ) = Aeration MLSS Concentration (mg/L) Settled Sludge Volume in 30 minutes (mL/L) × 1 , 000 mg/g ​ = MLSS SS V 30 ​ × 1 , 000 ​ +-----------------------------------------------------------------------------------------+

  • | SVI DIAGNOSTIC INTERPRETATION TABLE |
  • +-----------------------------------------------------------------------------------------+
  • | SVI Range (mL/g) | Settling Characteristic | Probable Cause / Operational Status |
  • +------------------+-----------------------------+----------------------------------------+
  • | < 80 mL/g | Rapid settling, compact | Old sludge, over-oxidized, pin floc, |
  • | | but leaves turbid supernatant| high ash content, low F/M ratio. |
  • +------------------+-----------------------------+----------------------------------------+
  • | 80 to 150 mL/g | Excellent settling rate, | Healthy activated sludge, clear liquor,|
  • | | uniform blanket, compact | balanced F/M, optimal floc structure. |
  • +------------------+-----------------------------+----------------------------------------+
  • | > 150 to 200+ mL/g| Slow settling, bulky, | Young sludge (under-oxidized), or |
  • | | poor compaction, high blanket| filamentous bulking (low DO/nutrients).|
  • +-----------------------------------------------------------------------------------------+
  • Return Activated Sludge (RAS) Flow Rate Optimization

Return Activated Sludge (RAS) recycles concentrated settled biomass from clarifier underflows back to the aeration basin headworks. The required RAS flow rate ( Q RAS Q_{\text{RAS}} Q RAS ​ ) can be paced using the 30-minute settleometer ratio or a clarifier solids mass balance:

Settleometer Ratio Method RAS Rate (%) = S S V 30 1 , 000 − S S V 30 × 100 % \mathbf{\text{RAS Rate (\%)} = \frac{SSV_{30}}{1,000 - SSV_{30}} \times 100\%} RAS Rate (%) = 1 , 000 − SS V 30 ​ SS V 30 ​ ​ × 100%

Mass Balance Method Q RAS × RAS TSS = ( Q inf + Q RAS ) × MLSS Q_{\text{RAS}} \times \text{RAS}_{\text{TSS}} = (Q_{\text{inf}} + Q_{\text{RAS}}) \times \text{MLSS} Q RAS ​ × RAS TSS ​ = ( Q inf ​ + Q RAS ​ ) × MLSS Q RAS = Q inf × ( MLSS RAS TSS − MLSS ) \mathbf{Q_{\text{RAS}} = Q_{\text{inf}} \times \left(\frac{\text{MLSS}}{\text{RAS}_{\text{TSS}} - \text{MLSS}}\right)} Q RAS ​ = Q inf ​ × ( RAS TSS ​ − MLSS MLSS ​ )

  • Step-by-Step Worked Exam Calculations
  • Worked Example 1: Food-to-Microorganism (F/M) Ratio

Problem: A municipal wastewater facility treats an influent flow of 3.00 MGD 3.00\text{ MGD} 3.00 MGD . Primary effluent entering the aeration basins has a BOD concentration of 180 mg/L 180\text{ mg/L} 180 mg/L . The total aeration basin volume is 1.20 MG 1.20\text{ MG} 1.20 MG . The mixed liquor suspended solids ( M L S S MLSS M L SS ) is 2 , 500 mg/L 2,500\text{ mg/L} 2 , 500 mg/L with an organic volatile content ( M L V S S MLVSS M L V SS ) of 75.0 % 75.0\% 75.0% . Calculate the F/M ratio.

Step 1: Calculate daily food applied (lbs BOD/day). Food = 3.00 MGD × 180 mg/L × 8.34 lbs/gal = 4 , 503.6 lbs BOD/day \text{Food} = 3.00\text{ MGD} \times 180\text{ mg/L} \times 8.34\text{ lbs/gal} = \mathbf{4,503.6\text{ lbs BOD/day}} Food = 3.00 MGD × 180 mg/L × 8.34 lbs/gal = 4 , 503.6 lbs BOD/day

Step 2: Calculate MLVSS concentration and microbial inventory. MLVSS (mg/L) = 2 , 500 mg/L × 0.750 = 1 , 875 mg/L \text{MLVSS (mg/L)} = 2,500\text{ mg/L} \times 0.750 = 1,875\text{ mg/L} MLVSS (mg/L) = 2 , 500 mg/L × 0.750 = 1 , 875 mg/L Microorganisms = 1.20 MG × 1 , 875 mg/L × 8.34 lbs/gal = 18 , 765.0 lbs MLVSS \text{Microorganisms} = 1.20\text{ MG} \times 1,875\text{ mg/L} \times 8.34\text{ lbs/gal} = \mathbf{18,765.0\text{ lbs MLVSS}} Microorganisms = 1.20 MG × 1 , 875 mg/L × 8.34 lbs/gal = 18 , 765.0 lbs MLVSS

Step 3: Calculate the F/M ratio. F/M = 4 , 503.6 lbs BOD/day 18 , 765.0 lbs MLVSS = 0.240 lb BOD/day per lb MLVSS ≈ 0.24 day − 1 \text{F/M} = \frac{4,503.6\text{ lbs BOD/day}}{18,765.0\text{ lbs MLVSS}} = \mathbf{0.240\text{ lb BOD/day per lb MLVSS}} \approx \mathbf{0.24\text{ day}^{-1}} F/M = 18 , 765.0 lbs MLVSS 4 , 503.6 lbs BOD/day ​ = 0.240 lb BOD/day per lb MLVSS ≈ 0.24 day − 1

Operational Check: A value of 0.24 day − 1 0.24\text{ day}^{-1} 0.24 day − 1 falls perfectly within the conventional activated sludge design window ( 0.20 to 0.50 day − 1 0.20\text{ to }0.50\text{ day}^{-1} 0.20 to 0.50 day − 1 ).

Worked Example 2: Sludge Volume Index (SVI) Determination

Problem: An operator collects a grab sample of mixed liquor from the aeration basin discharge. The laboratory test reveals an M L S S MLSS M L SS concentration of 2 , 800 mg/L 2,800\text{ mg/L} 2 , 800 mg/L . A 30-minute settleometer test performed in a 1 , 000 mL 1,000\text{ mL} 1 , 000 mL cylinder yields a settled sludge volume ( S S V 30 SSV_{30} SS V 30 ​ ) of 260 mL/L 260\text{ mL/L} 260 mL/L . Calculate the SVI and diagnose settling performance.

Step 1: Apply the SVI formula. SVI = S S V 30 (mL/L) × 1 , 000 mg/g MLSS (mg/L) = 260 mL/L × 1 , 000 mg/g 2 , 800 mg/L = 260 , 000 2 , 800 = 92.86 mL/g ≈ 92.9 mL/g \text{SVI} = \frac{SSV_{30}\text{ (mL/L)} \times 1,000\text{ mg/g}}{\text{MLSS (mg/L)}} = \frac{260\text{ mL/L} \times 1,000\text{ mg/g}}{2,800\text{ mg/L}} = \frac{260,000}{2,800} = \mathbf{92.86\text{ mL/g}} \approx \mathbf{92.9\text{ mL/g}} SVI = MLSS (mg/L) SS V 30 ​ (mL/L) × 1 , 000 mg/g ​ = 2 , 800 mg/L 260 mL/L × 1 , 000 mg/g ​ = 2 , 800 260 , 000 ​ = 92.86 mL/g ≈ 92.9 mL/g

Step 2: Diagnosis. An SVI of 92.9 mL/g 92.9\text{ mL/g} 92.9 mL/g is within the optimal 80 to 150 mL/g 80\text{ to }150\text{ mL/g} 80 to 150 mL/g range, indicating robust, well-settling floc with good compaction and clear supernatant.

Worked Example 3: Target WAS Pumping Rate for MCRT Control

Problem: A plant operates an aeration basin with a total volume of 2.00 MG 2.00\text{ MG} 2.00 MG and maintains an M L S S MLSS M L SS of 2 , 400 mg/L 2,400\text{ mg/L} 2 , 400 mg/L . The plant effluent flow is 4.00 MGD 4.00\text{ MGD} 4.00 MGD with an effluent TSS of 12.0 mg/L 12.0\text{ mg/L} 12.0 mg/L . The target MCRT is 8.0 days 8.0\text{ days} 8.0 days . Clarifier underflow Waste Activated Sludge ( W A S WAS W A S ) concentration is 7 , 500 mg/L 7,500\text{ mg/L} 7 , 500 mg/L . Calculate:

Total system MLSS inventory under aeration.

Daily effluent solids loss.

Required daily WAS mass to maintain target MCRT.

Required WAS flow rate in MGD and Gallons per Day (GPD).

Step 1: Calculate total aeration MLSS inventory. System MLSS (lbs) = 2.00 MG × 2 , 400 mg/L × 8.34 = 40 , 032.0 lbs \text{System MLSS (lbs)} = 2.00\text{ MG} \times 2,400\text{ mg/L} \times 8.34 = \mathbf{40,032.0\text{ lbs}} System MLSS (lbs) = 2.00 MG × 2 , 400 mg/L × 8.34 = 40 , 032.0 lbs

Step 2: Calculate daily target total solids removal. Total Daily Loss Required = 40 , 032.0 lbs 8.0 days = 5 , 004.0 lbs/day \text{Total Daily Loss Required} = \frac{40,032.0\text{ lbs}}{8.0\text{ days}} = \mathbf{5,004.0\text{ lbs/day}} Total Daily Loss Required = 8.0 days 40 , 032.0 lbs ​ = 5 , 004.0 lbs/day

Step 3: Calculate daily effluent TSS loss. Effluent TSS Loss (lbs/day) = 4.00 MGD × 12.0 mg/L × 8.34 = 400.32 lbs/day \text{Effluent TSS Loss (lbs/day)} = 4.00\text{ MGD} \times 12.0\text{ mg/L} \times 8.34 = \mathbf{400.32\text{ lbs/day}} Effluent TSS Loss (lbs/day) = 4.00 MGD × 12.0 mg/L × 8.34 = 400.32 lbs/day

Step 4: Calculate net WAS mass needed per day. Required WAS (lbs/day) = 5 , 004.0 lbs/day − 400.32 lbs/day = 4 , 603.68 lbs/day \text{Required WAS (lbs/day)} = 5,004.0\text{ lbs/day} - 400.32\text{ lbs/day} = \mathbf{4,603.68\text{ lbs/day}} Required WAS (lbs/day) = 5 , 004.0 lbs/day − 400.32 lbs/day = 4 , 603.68 lbs/day

Step 5: Calculate WAS flow rate in MGD and GPD. Q WAS ( MGD ) = 4 , 603.68 lbs/day 7 , 500 mg/L × 8.34 lbs/gal = 4 , 603.68 62 , 550 = 0.0736 MGD Q_{\text{WAS}} (\text{MGD}) = \frac{4,603.68\text{ lbs/day}}{7,500\text{ mg/L} \times 8.34\text{ lbs/gal}} = \frac{4,603.68}{62,550} = \mathbf{0.0736\text{ MGD}} Q WAS ​ ( MGD ) = 7 , 500 mg/L × 8.34 lbs/gal 4 , 603.68 lbs/day ​ = 62 , 550 4 , 603.68 ​ = 0.0736 MGD WAS Flow (GPD) = 0.0736 MGD × 1 , 000 , 000 = 73 , 600 GPD (or 51.1 gpm) \text{WAS Flow (GPD)} = 0.0736\text{ MGD} \times 1,000,000 = \mathbf{73,600\text{ GPD}}\text{ (or } 51.1\text{ gpm)} WAS Flow (GPD) = 0.0736 MGD × 1 , 000 , 000 = 73 , 600 GPD (or 51.1 gpm)

Loading diagram... Activated Sludge Mass Balance & Process Control Control Loop