Study guide

11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates

Key Takeaways Explain This Topic AI

Hydraulic Retention Time (HRT or Detention Time) measures the theoretical residence time of water in a basin: HRT (hours) = (Volume in gal × 24 hr/day) / Flow (gpd).

Clarifier Surface Overflow Rate (SOR) represents the upward hydraulic loading per unit of basin surface area: SOR (gpd/sq ft) = Flow (gpd) / Surface Area (sq ft).

Weir Overflow Rate (WOR) assesses linear hydraulic takeoff: WOR (gpd/linear ft) = Flow (gpd) / Total Weir Length (linear ft), where peripheral circular weir length equals π × Diameter.

Filter Hydraulic Loading Rate (HLR) measures filtration velocity: HLR (gpm/sq ft) = Flow (gpm) / Filter Surface Area (sq ft), with conventional filters operating at 2–4 gpm/sq ft and high-rate filters at 4–6 gpm/sq ft.

Backwash Rise Rate translates volumetric backwash flow into vertical upflow velocity: Rise Rate (inches/min) = (Backwash Rate in gpm/sq ft × 12 in/ft) / 7.48 gal/cu ft.

Last updated: August 2026

Hydraulic Loading, Retention & Clarification Mechanics

Sedimentation basins, clarifiers, flocculators, and filters depend on specific hydraulic flow regimes to achieve optimal particle settling and filtration efficiency. If flow rates exceed hydraulic design criteria, retention times drop, fluid velocities rise, and floc particles are carried over into effluent launders or driven deep into filter media. Certified operators in Colorado must regularly calculate Hydraulic Retention Time (HRT) , Surface Overflow Rate (SOR) , Weir Overflow Rate (WOR) , and Filter Hydraulic Loading Rates (HLR) to diagnose process upsets and adjust operational unit sequencing.

Hydraulic Retention Time (HRT) / Detention Time

Hydraulic Retention Time (also termed Detention Time ) represents the theoretical average time that a given parcel of water or wastewater resides within a treatment vessel. It is fundamentally calculated as volume divided by flow rate: Retention Time = Basin Volume Volumetric Flow Rate \mathbf{\text{Retention Time} = \frac{\text{Basin Volume}}{\text{Volumetric Flow Rate}}} Retention Time = Volumetric Flow Rate Basin Volume ​ +-------------------------------------------------------------------------+

  • | DETENTION TIME FORMULA VARIATIONS |
  • +-------------------------------------------------------------------------+
  • | 1. Detention Time in Days: |
  • | DT (days) = Volume (gal) / Flow Rate (gpd) |
  • | DT (days) = Volume (MG) / Flow Rate (MGD) |
  • | |
  • | 2. Detention Time in Hours: |
  • | DT (hours) = [Volume (gal) × 24 hr/day] / Flow Rate (gpd) |
  • | DT (hours) = [Volume (MG) × 24 hr/day] / Flow Rate (MGD) |
  • | |
  • | 3. Detention Time in Minutes: |
  • | DT (min) = [Volume (gal) × 1,440 min/day] / Flow Rate (gpd) |
  • | DT (min) = Volume (gal) / Flow Rate (gpm) |
  • +-------------------------------------------------------------------------+
  • Typical Industry Hydraulic Retention Standards
  • Treatment Unit Process Typical Design HRT Range Primary Purpose
  • Rapid Mix Chamber 15 to 60 seconds (0.25–1.0 min) Instantaneous dispersion of primary coagulants
  • Flocculation Basins 20 to 45 minutes Gentle particle collisions to build settleable floc
  • Primary Clarifiers 1.5 to 2.5 hours Gravity settling of raw settleable organic solids
  • Secondary Clarifiers 2.0 to 4.0 hours Separation of biological mixed liquor suspended solids
  • Chlorine Contact Basin 15 to 30 minutes (at peak hourly flow) Pathogen inactivation ( C T CT CT compliance)
  • Aerobic Digester 15 to 25 days Volatile solids reduction and pathogen stabilization
  • Clarifier Surface Overflow Rate (SOR) / Hydraulic Loading Rate

The Surface Overflow Rate (SOR) —also termed the Hydraulic Surface Loading Rate —measures the volume of water applied daily per square foot of clarifier surface area: SOR (gpd/sq ft) = Influent Flow Rate (gpd) Basin Surface Area (sq ft) = Flow (MGD) × 1 , 000 , 000 Surface Area (sq ft) \mathbf{\text{SOR (gpd/sq ft)} = \frac{\text{Influent Flow Rate (gpd)}}{\text{Basin Surface Area (sq ft)}} = \frac{\text{Flow (MGD)} \times 1,000,000}{\text{Surface Area (sq ft)}}} SOR (gpd/sq ft) = Basin Surface Area (sq ft) Influent Flow Rate (gpd) ​ = Surface Area (sq ft) Flow (MGD) × 1 , 000 , 000 ​ +-------------------------------------------------------------------------+

  • | CLARIFIER SURFACE AREA FORMULAS |
  • +-------------------------------------------------------------------------+
  • | Circular Clarifier: Surface Area (sq ft) = 0.785 × Diameter² (ft²) |
  • | Rectangular Clarifier: Surface Area (sq ft) = Length (ft) × Width (ft) |
  • +-------------------------------------------------------------------------+
  • Physical Significance of SOR

Under Hazen's Theory of Ideal Sedimentation , a settling particle will be successfully captured if its downward settling velocity ( v s v_s v s ​ ) equals or exceeds the upward hydraulic surface overflow velocity ( v o = SOR v_o = \text{SOR} v o ​ = SOR ). The depth of the basin influences retention time but has no theoretical effect on the critical particle settling velocity cutoff; only surface area determines the overflow velocity threshold. Typical secondary clarifier SOR design values range from 400 to 800 gpd/sq ft under average flow conditions and up to 1,000 to 1,200 gpd/sq ft during peak hydraulic events.

Weir Overflow Rate (WOR) & Launder Hydraulics

Clarifier effluent is collected across perimeter or inboard v-notch weirs. The Weir Overflow Rate (WOR) (or Weir Loading Rate) measures the volume of clarified effluent passing over each linear foot of weir crest per day: WOR (gpd/linear ft) = Influent Flow Rate (gpd) Total Active Weir Length (linear ft) \mathbf{\text{WOR (gpd/linear ft)} = \frac{\text{Influent Flow Rate (gpd)}}{\text{Total Active Weir Length (linear ft)}}} WOR (gpd/linear ft) = Total Active Weir Length (linear ft) Influent Flow Rate (gpd) ​ +-------------------------------------------------------------------------+

  • | WEIR LENGTH DETERMINATION RULES |
  • +-------------------------------------------------------------------------+
  • | 1. Peripheral Circular Weir (single outer edge): |
  • | Length (ft) = π × Diameter = 3.1416 × D |
  • | |
  • | 2. Inboard Double-Sided Circular Launder (weir on both walls): |
  • | Length (ft) = (π × D_inner) + (π × D_outer) ≈ 2 × π × D_centerline |
  • | |
  • | 3. Rectangular Clarifier End / Finger Weirs: |
  • | Length (ft) = Sum of all active weir crest edges |
  • +-------------------------------------------------------------------------+

Regulatory Standards: Both CDPHE Design Criteria and the Ten States Standards generally mandate that Weir Overflow Rates not exceed 10,000 to 15,000 gpd/linear foot for standard plants, or 20,000 gpd/linear foot for larger facilities with inboard launders. Excessive WOR generates high localized exit velocities that pull settled sludge up into the effluent trough (scouring/pin floc carryover).

Granular Media Filter Loading Rate & Backwash Rise Rate

Granular media filters (sand, dual-media anthracite/sand, mixed-media) treat water downward during filtration and expand upward during backwash cycles.

Filter Hydraulic Loading Rate (HLR)

Filter loading rate evaluates flow applied per square foot of media surface area and is expressed in gallons per minute per square foot ( gpm/sq ft \text{gpm/sq ft} gpm/sq ft ) : Filter Loading Rate (gpm/sq ft) = Operating Flow Rate (gpm) Filter Surface Area (sq ft) = Flow (gpm) Length (ft) × Width (ft) \mathbf{\text{Filter Loading Rate (gpm/sq ft)} = \frac{\text{Operating Flow Rate (gpm)}}{\text{Filter Surface Area (sq ft)}} = \frac{\text{Flow (gpm)}}{\text{Length (ft)} \times \text{Width (ft)}}} Filter Loading Rate (gpm/sq ft) = Filter Surface Area (sq ft) Operating Flow Rate (gpm) ​ = Length (ft) × Width (ft) Flow (gpm) ​

Conventional Rapid Sand Filters: 2.0 to 3.0 gpm/sq ft 2.0\text{ to }3.0\text{ gpm/sq ft} 2.0 to 3.0 gpm/sq ft

High-Rate Dual/Mixed Media Filters: 4.0 to 6.0 gpm/sq ft 4.0\text{ to }6.0\text{ gpm/sq ft} 4.0 to 6.0 gpm/sq ft

Membrane Microfiltration: 0.5 to 1.5 gpm/sq ft 0.5\text{ to }1.5\text{ gpm/sq ft} 0.5 to 1.5 gpm/sq ft (expressed as flux in gfd)

Filter Backwash Rise Rate

During backwash, clean treated water is pumped upward at high rates ( 15 to 22 gpm/sq ft 15\text{ to }22\text{ gpm/sq ft} 15 to 22 gpm/sq ft ) to fluidize the media bed and release trapped solids. The upward vertical velocity is termed the Rise Rate and is expressed in inches per minute ( in/min \text{in/min} in/min ) : Rise Velocity (ft/min) = Backwash Rate (gpm/sq ft) 7.48 gal/cu ft \text{Rise Velocity (ft/min)} = \frac{\text{Backwash Rate (gpm/sq ft)}}{7.48\text{ gal/cu ft}} Rise Velocity (ft/min) = 7.48 gal/cu ft Backwash Rate (gpm/sq ft) ​ Rise Rate (in/min) = Backwash Rate (gpm/sq ft) × 12 in/ft 7.48 gal/cu ft = Backwash Rate (gpm/sq ft) × 1.604 \mathbf{\text{Rise Rate (in/min)} = \frac{\text{Backwash Rate (gpm/sq ft)} \times 12\text{ in/ft}}{7.48\text{ gal/cu ft}} = \text{Backwash Rate (gpm/sq ft)} \times 1.604} Rise Rate (in/min) = 7.48 gal/cu ft Backwash Rate (gpm/sq ft) × 12 in/ft ​ = Backwash Rate (gpm/sq ft) × 1.604 Rise Rate (in/min) = Total Backwash Flow (gpm) × 12 in/ft Filter Area (sq ft) × 7.48 gal/cu ft \text{Rise Rate (in/min)} = \frac{\text{Total Backwash Flow (gpm)} \times 12\text{ in/ft}}{\text{Filter Area (sq ft)} \times 7.48\text{ gal/cu ft}} Rise Rate (in/min) = Filter Area (sq ft) × 7.48 gal/cu ft Total Backwash Flow (gpm) × 12 in/ft ​

  • Step-by-Step Worked Exam Calculations
  • Worked Example 1: Rectangular Primary Clarifier HRT & SOR

Problem: A rectangular primary sedimentation basin has interior dimensions of 80.0 ft length 80.0\text{ ft length} 80.0 ft length , 25.0 ft width 25.0\text{ ft width} 25.0 ft width , and a water depth of 12.0 ft 12.0\text{ ft} 12.0 ft . The plant flow rate entering this clarifier is 2.40 MGD 2.40\text{ MGD} 2.40 MGD . Calculate:

The hydraulic retention time (HRT) in hours.

The Surface Overflow Rate (SOR) in gpd/sq ft.

Step 1: Calculate basin surface area and total liquid volume. Surface Area = 80.0 ft × 25.0 ft = 2 , 000.0 sq ft \text{Surface Area} = 80.0\text{ ft} \times 25.0\text{ ft} = 2,000.0\text{ sq ft} Surface Area = 80.0 ft × 25.0 ft = 2 , 000.0 sq ft Volume (cu ft) = 2 , 000.0 sq ft × 12.0 ft = 24 , 000.0 cu ft \text{Volume (cu ft)} = 2,000.0\text{ sq ft} \times 12.0\text{ ft} = 24,000.0\text{ cu ft} Volume (cu ft) = 2 , 000.0 sq ft × 12.0 ft = 24 , 000.0 cu ft Volume (gal) = 24 , 000.0 cu ft × 7.48 gal/cu ft = 179 , 520 gallons \text{Volume (gal)} = 24,000.0\text{ cu ft} \times 7.48\text{ gal/cu ft} = 179,520\text{ gallons} Volume (gal) = 24 , 000.0 cu ft × 7.48 gal/cu ft = 179 , 520 gallons

Step 2: Calculate Hydraulic Retention Time (HRT) in hours. HRT (hours) = 179 , 520 gal × 24 hr/day 2 , 400 , 000 gpd = 4 , 308 , 480 2 , 400 , 000 = 1.795 hours ≈ 1.80 hours (or 107.7 min) \text{HRT (hours)} = \frac{179,520\text{ gal} \times 24\text{ hr/day}}{2,400,000\text{ gpd}} = \frac{4,308,480}{2,400,000} = \mathbf{1.795\text{ hours}} \approx \mathbf{1.80\text{ hours}}\text{ (or } 107.7\text{ min)} HRT (hours) = 2 , 400 , 000 gpd 179 , 520 gal × 24 hr/day ​ = 2 , 400 , 000 4 , 308 , 480 ​ = 1.795 hours ≈ 1.80 hours (or 107.7 min)

Step 3: Calculate Surface Overflow Rate (SOR). SOR (gpd/sq ft) = 2 , 400 , 000 gpd 2 , 000.0 sq ft = 1 , 200 gpd/sq ft \text{SOR (gpd/sq ft)} = \frac{2,400,000\text{ gpd}}{2,000.0\text{ sq ft}} = \mathbf{1,200\text{ gpd/sq ft}} SOR (gpd/sq ft) = 2 , 000.0 sq ft 2 , 400 , 000 gpd ​ = 1 , 200 gpd/sq ft

Worked Example 2: Circular Clarifier SOR & Weir Overflow Rate

Problem: A circular secondary clarifier with a diameter of 75.0 ft 75.0\text{ ft} 75.0 ft treats a peak secondary flow of 3.50 MGD 3.50\text{ MGD} 3.50 MGD . Clarified effluent discharges over a peripheral weir running the full circumference of the tank. Calculate:

The Surface Overflow Rate (SOR) in gpd/sq ft.

The Weir Overflow Rate (WOR) in gpd/linear ft.

Step 1: Calculate surface area. A = 0.785 × ( 75.0 ft ) 2 = 0.785 × 5 , 625 ft 2 = 4 , 415.63 sq ft A = 0.785 \times (75.0\text{ ft})^2 = 0.785 \times 5,625\text{ ft}^2 = 4,415.63\text{ sq ft} A = 0.785 × ( 75.0 ft ) 2 = 0.785 × 5 , 625 ft 2 = 4 , 415.63 sq ft

Step 2: Calculate Surface Overflow Rate (SOR). SOR = 3 , 500 , 000 gpd 4 , 415.63 sq ft = 792.6 gpd/sq ft ≈ 793 gpd/sq ft \text{SOR} = \frac{3,500,000\text{ gpd}}{4,415.63\text{ sq ft}} = \mathbf{792.6\text{ gpd/sq ft}} \approx \mathbf{793\text{ gpd/sq ft}} SOR = 4 , 415.63 sq ft 3 , 500 , 000 gpd ​ = 792.6 gpd/sq ft ≈ 793 gpd/sq ft

Step 3: Calculate peripheral weir length. Weir Length (ft) = π × D = 3.1416 × 75.0 ft = 235.62 linear ft \text{Weir Length (ft)} = \pi \times D = 3.1416 \times 75.0\text{ ft} = 235.62\text{ linear ft} Weir Length (ft) = π × D = 3.1416 × 75.0 ft = 235.62 linear ft

Step 4: Calculate Weir Overflow Rate (WOR). WOR = 3 , 500 , 000 gpd 235.62 ft = 14 , 854.4 gpd/linear ft ≈ 14 , 854 gpd/linear ft \text{WOR} = \frac{3,500,000\text{ gpd}}{235.62\text{ ft}} = \mathbf{14,854.4\text{ gpd/linear ft}} \approx \mathbf{14,854\text{ gpd/linear ft}} WOR = 235.62 ft 3 , 500 , 000 gpd ​ = 14 , 854.4 gpd/linear ft ≈ 14 , 854 gpd/linear ft

Worked Example 3: Filter Hydraulic Loading & Backwash Rise Rate

Problem: A dual-media gravity filter cell measures 18.0 ft by 22.0 ft 18.0\text{ ft by } 22.0\text{ ft} 18.0 ft by 22.0 ft . During standard filtration, the cell processes 1 , 500 gpm 1,500\text{ gpm} 1 , 500 gpm . During backwash, the backwash supply pump delivers 6 , 000 gpm 6,000\text{ gpm} 6 , 000 gpm . Calculate:

The filter hydraulic loading rate in gpm/sq ft.

The backwash rise rate in inches per minute (in/min).

Step 1: Calculate filter surface area. A = 18.0 ft × 22.0 ft = 396.0 sq ft A = 18.0\text{ ft} \times 22.0\text{ ft} = 396.0\text{ sq ft} A = 18.0 ft × 22.0 ft = 396.0 sq ft

Step 2: Calculate filter loading rate (HLR). HLR (gpm/sq ft) = 1 , 500 gpm 396.0 sq ft = 3.79 gpm/sq ft \text{HLR (gpm/sq ft)} = \frac{1,500\text{ gpm}}{396.0\text{ sq ft}} = \mathbf{3.79\text{ gpm/sq ft}} HLR (gpm/sq ft) = 396.0 sq ft 1 , 500 gpm ​ = 3.79 gpm/sq ft

Step 3: Calculate backwash loading rate. Backwash Loading = 6 , 000 gpm 396.0 sq ft = 15.15 gpm/sq ft \text{Backwash Loading} = \frac{6,000\text{ gpm}}{396.0\text{ sq ft}} = 15.15\text{ gpm/sq ft} Backwash Loading = 396.0 sq ft 6 , 000 gpm ​ = 15.15 gpm/sq ft

Step 4: Calculate backwash rise rate in inches per minute. Rise Rate (in/min) = 15.15 gpm/sq ft × 12 in/ft 7.48 gal/cu ft = 181.80 7.48 = 24.3 in/min \text{Rise Rate (in/min)} = \frac{15.15\text{ gpm/sq ft} \times 12\text{ in/ft}}{7.48\text{ gal/cu ft}} = \frac{181.80}{7.48} = \mathbf{24.3\text{ in/min}} Rise Rate (in/min) = 7.48 gal/cu ft 15.15 gpm/sq ft × 12 in/ft ​ = 7.48 181.80 ​ = 24.3 in/min

Loading diagram... Clarification & Filtration Hydraulic Parameter Matrix