Study guide

11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency

Key Takeaways Explain This Topic AI

Static hydraulic head and gauge pressure are directly convertible: Pressure (psi) = Head (ft) / 2.31 = Head (ft) × 0.433 psi/ft.

Total Dynamic Head (TDH) represents the total equivalent energy the pump must impart: TDH = Static Head + Friction Head Losses (h_f) + Minor Losses (h_m) + Velocity Head (V²/2g).

Water Horsepower (WHP) represents theoretical useful hydraulic work: WHP = [Flow (gpm) × TDH (ft) × Specific Gravity] / 3,960.

Brake Horsepower (BHP) accounts for pump mechanical/hydraulic efficiency: BHP = WHP / Pump Efficiency, while Motor Horsepower (MHP) accounts for driver electrical efficiency: MHP = BHP / Motor Efficiency.

Overall Wire-to-Water Efficiency is the product of pump and motor efficiencies (η_overall = η_pump × η_motor), enabling direct calculation of electrical energy consumption (kW) and annual utility power costs.

Last updated: August 2026

Hydraulics, Head Calculations & Pumping Mechanics

Water distribution and wastewater collection networks rely on pumps to overcome elevation differences (static head) and pipe wall friction resistance (dynamic head). In Colorado, where dramatic elevation changes across mountainous terrain create extreme pressure variations, operators must master hydraulic head conversions, evaluate pressure zones, calculate Water Horsepower (WHP) and Brake Horsepower (BHP) , and audit Wire-to-Water Efficiency to minimize municipal electrical energy expenditures.

Static Head, Pressure & Elevation Relationships

Hydrostatic pressure is created by the weight of water acting over a unit surface area. Because a 1.0 foot 1.0\text{ foot} 1.0 foot column of water with a base of 1.0 square inch 1.0\text{ square inch} 1.0 square inch weighs exactly 0.4333 lbs 0.4333\text{ lbs} 0.4333 lbs : 1 vertical foot of water head = 0.4333 psi ≈ 0.433 psi \mathbf{1\text{ vertical foot of water head} = 0.4333\text{ psi} \approx 0.433\text{ psi}} 1 vertical foot of water head = 0.4333 psi ≈ 0.433 psi 1 psi of pressure = 1 0.4333 = 2.308 feet of water head ≈ 2.31 feet of head \mathbf{1\text{ psi of pressure} = \frac{1}{0.4333} = 2.308\text{ feet of water head} \approx 2.31\text{ feet of head}} 1 psi of pressure = 0.4333 1 ​ = 2.308 feet of water head ≈ 2.31 feet of head +-------------------------------------------------------------------------+

  • | PRESSURE & HEAD CONVERSION FORMULAS |
  • +-------------------------------------------------------------------------+
  • | Pressure (psi) = Head (ft) / 2.31 ft/psi OR Head (ft) × 0.433 psi/ft|
  • | Head (ft) = Pressure (psi) × 2.31 ft/psi OR Pressure (psi) / 0.433|
  • +-------------------------------------------------------------------------+
  • Pressure Zone Calculations in Mountainous Terrain

When water flows downhill from a storage tank at elevation Z tank Z_{\text{tank}} Z tank ​ to a lower distribution node at elevation Z node Z_{\text{node}} Z node ​ , the static pressure generated at the lower node is proportional to the elevation drop: Δ Static Head (ft) = Z tank − Z node \Delta \text{Static Head (ft)} = Z_{\text{tank}} - Z_{\text{node}} Δ Static Head (ft) = Z tank ​ − Z node ​ P static ( psi ) = Z tank − Z node 2.31 ft/psi P_{\text{static}} (\text{psi}) = \frac{Z_{\text{tank}} - Z_{\text{node}}}{2.31\text{ ft/psi}} P static ​ ( psi ) = 2.31 ft/psi Z tank ​ − Z node ​ ​

Colorado Operational Reality: A drop of 231 feet 231\text{ feet} 231 feet generates 100 psi 100\text{ psi} 100 psi of static water pressure. In mountainous communities where elevation differentials exceed 400 – 600 feet 400\text{–}600\text{ feet} 400 – 600 feet , line pressures can exceed 175 – 250 psi 175\text{–}250\text{ psi} 175 – 250 psi , necessitating pressure-reducing valve (PRV) stations to prevent water main ruptures and residential plumbing failures.

Total Dynamic Head (TDH)

Total Dynamic Head (TDH) is the total equivalent vertical height against which a pump must work during active operation. It includes static elevation differences, dynamic pipe friction losses, minor fitting restrictions, and kinetic velocity head: TDH (ft) = Total Static Head + Friction Head Loss ( h f ) + Minor Fitting Losses ( h m ) + Velocity Head ( V 2 2 g ) \mathbf{\text{TDH (ft)} = \text{Total Static Head} + \text{Friction Head Loss } (h_f) + \text{Minor Fitting Losses } (h_m) + \text{Velocity Head } \left(\frac{V^2}{2g}\right)} TDH (ft) = Total Static Head + Friction Head Loss ( h f ​ ) + Minor Fitting Losses ( h m ​ ) + Velocity Head ( 2g V 2 ​ ) +-------------------------------------------------------------------------+

  • | TOTAL STATIC HEAD DEFINITIONS |
  • +-------------------------------------------------------------------------+
  • | 1. Flooded Suction Condition (water level ABOVE pump centerline): |
  • | Total Static Head = Static Discharge Head - Static Suction Head |
  • | |
  • | 2. Suction Lift Condition (water level BELOW pump centerline): |
  • | Total Static Head = Static Discharge Head + Static Suction Lift |
  • +-------------------------------------------------------------------------+
  • Calculating TDH from Pressure Gauge Readings

In operating pump stations, operators determine TDH directly from calibrated suction and discharge pressure gauges: TDH (ft) = [ P discharge ( psi ) − P suction ( psi ) ] × 2.31 ft/psi + Δ Z gauges ( ft ) \mathbf{\text{TDH (ft)} = [P_{\text{discharge}} (\text{psi}) - P_{\text{suction}} (\text{psi})] \times 2.31\text{ ft/psi} + \Delta Z_{\text{gauges}} (\text{ft})} TDH (ft) = [ P discharge ​ ( psi ) − P suction ​ ( psi )] × 2.31 ft/psi + Δ Z gauges ​ ( ft )

(Note: If the suction gauge is under vacuum/suction lift reading in inches of mercury, convert vacuum to equivalent negative feet of head: 1 in Hg = 1.13 ft of water 1\text{ in Hg} = 1.13\text{ ft of water} 1 in Hg = 1.13 ft of water ).

The Horsepower Cascade: Water, Brake & Motor Horsepower

Energy transfer from the electrical power grid to the moving water occurs across three progressive stages, with mechanical and electrical friction causing energy losses at each transition: +-------------------------------------------------------------------------+

  • | THE HORSEPOWER CASCADE |
  • +-------------------------------------------------------------------------+
  • | |
  • | [ Electrical Grid ] |
  • | │ |
  • | ▼ (Motor Efficiency: 88% - 96%) |
  • | [ Motor Horsepower (MHP) / Input HP ] |
  • | │ |
  • | ▼ (Pump Efficiency: 70% - 86%) |
  • | [ Brake Horsepower (BHP) / Shaft HP ] |
  • | │ |
  • | ▼ (Hydraulic Energy Delivered) |
  • | [ Water Horsepower (WHP) ] |
  • | |
  • +-------------------------------------------------------------------------+
  • 1. Water Horsepower (WHP)

Water Horsepower represents the theoretical useful work imparted directly into the liquid stream to lift and move the fluid: W H P = Flow Rate (gpm) × TDH (ft) × Specific Gravity 3 , 960 \mathbf{WHP = \frac{\text{Flow Rate (gpm)} \times \text{TDH (ft)} \times \text{Specific Gravity}}{3,960}} WHP = 3 , 960 Flow Rate (gpm) × TDH (ft) × Specific Gravity ​

Proof of the 3,960 Constant: One horsepower is defined as 33 , 000 foot-pounds per minute 33,000\text{ foot-pounds per minute} 33 , 000 foot-pounds per minute . Because one gallon of water weighs 8.34 lbs 8.34\text{ lbs} 8.34 lbs : Constant = 33 , 000 ft-lbs/min 8.34 lbs/gal = 3 , 956.83 ≈ 3 , 960 \text{Constant} = \frac{33,000\text{ ft-lbs/min}}{8.34\text{ lbs/gal}} = 3,956.83 \approx \mathbf{3,960} Constant = 8.34 lbs/gal 33 , 000 ft-lbs/min ​ = 3 , 956.83 ≈ 3 , 960

2. Brake Horsepower (BHP)

Brake Horsepower represents the mechanical shaft power that the electric motor must deliver to the pump shaft coupling, accounting for hydraulic and mechanical friction inside the pump volute and impeller: B H P = Water Horsepower (WHP) Pump Efficiency (as decimal) = Flow (gpm) × TDH (ft) 3 , 960 × η pump \mathbf{BHP = \frac{\text{Water Horsepower (WHP)}}{\text{Pump Efficiency (as decimal)}} = \frac{\text{Flow (gpm)} \times \text{TDH (ft)}}{3,960 \times \eta_{\text{pump}}}} BHP = Pump Efficiency (as decimal) Water Horsepower (WHP) ​ = 3 , 960 × η pump ​ Flow (gpm) × TDH (ft) ​

3. Motor Horsepower (MHP) / Electrical Input Power

Motor Horsepower (or Electrical Input Horsepower) is the power drawn by the motor from electrical power feeds, accounting for electrical resistance, magnetic losses, and winding heat: M H P = Brake Horsepower (BHP) Motor Efficiency (as decimal) = Flow (gpm) × TDH (ft) 3 , 960 × η pump × η motor \mathbf{MHP = \frac{\text{Brake Horsepower (BHP)}}{\text{Motor Efficiency (as decimal)}} = \frac{\text{Flow (gpm)} \times \text{TDH (ft)}}{3,960 \times \eta_{\text{pump}} \times \eta_{\text{motor}}}} MHP = Motor Efficiency (as decimal) Brake Horsepower (BHP) ​ = 3 , 960 × η pump ​ × η motor ​ Flow (gpm) × TDH (ft) ​

Wire-to-Water Efficiency & Energy Economics

Wire-to-Water Efficiency ( η overall \eta_{\text{overall}} η overall ​ ) is the total combined efficiency of the pumping system, calculated as the ratio of useful hydraulic power output ( W H P WHP W H P ) to total electrical power input: η overall = η pump × η motor = Water Horsepower (WHP) Motor Horsepower (MHP) × 100 % \mathbf{\eta_{\text{overall}} = \eta_{\text{pump}} \times \eta_{\text{motor}} = \frac{\text{Water Horsepower (WHP)}}{\text{Motor Horsepower (MHP)}} \times 100\%} η overall ​ = η pump ​ × η motor ​ = Motor Horsepower (MHP) Water Horsepower (WHP) ​ × 100%

Electrical Power Consumption & Cost Calculations

Electric utilities meter power in Kilowatts (kW) and bill consumption in Kilowatt-hours (kWh) . The standard conversion is 1 Horsepower (HP) = 0.746 Kilowatts (kW) 1\text{ Horsepower (HP)} = 0.746\text{ Kilowatts (kW)} 1 Horsepower (HP) = 0.746 Kilowatts (kW) : Power Demand (kW) = MHP (Input HP) × 0.746 kW/HP = BHP × 0.746 η motor \mathbf{\text{Power Demand (kW)} = \text{MHP (Input HP)} \times 0.746\text{ kW/HP} = \frac{\text{BHP} \times 0.746}{\eta_{\text{motor}}}} Power Demand (kW) = MHP (Input HP) × 0.746 kW/HP = η motor ​ BHP × 0.746 ​ Energy Consumed (kWh) = Power Demand (kW) × Operating Time (hours) \text{Energy Consumed (kWh)} = \text{Power Demand (kW)} \times \text{Operating Time (hours)} Energy Consumed (kWh) = Power Demand (kW) × Operating Time (hours) Operating Cost ($) = Energy Consumed (kWh) × Electricity Rate ($/kWh) \mathbf{\text{Operating Cost (\$)} = \text{Energy Consumed (kWh)} \times \text{Electricity Rate (\$/kWh)}} Operating Cost ($) = Energy Consumed (kWh) × Electricity Rate ($/kWh)

  • Step-by-Step Worked Exam Calculations
  • Worked Example 1: Pressure & Hydraulic Head in Mountain Distribution

Problem: An elevated storage tank in a Colorado foothills distribution system has a top water surface elevation of 6 , 450.0 ft 6,450.0\text{ ft} 6 , 450.0 ft . A pressure gauge on a fire hydrant at a valley road intersection has an elevation of 6 , 219.0 ft 6,219.0\text{ ft} 6 , 219.0 ft . Calculate the static water pressure in psi at the hydrant when the storage tank is completely full.

Step 1: Calculate the total static head in feet. Static Head (ft) = 6 , 450.0 ft − 6 , 219.0 ft = 231.0 ft \text{Static Head (ft)} = 6,450.0\text{ ft} - 6,219.0\text{ ft} = 231.0\text{ ft} Static Head (ft) = 6 , 450.0 ft − 6 , 219.0 ft = 231.0 ft

Step 2: Convert static head to pressure in psi. P (psi) = 231.0 ft 2.31 ft/psi = 100.0 psi P\text{ (psi)} = \frac{231.0\text{ ft}}{2.31\text{ ft/psi}} = \mathbf{100.0\text{ psi}} P (psi) = 2.31 ft/psi 231.0 ft ​ = 100.0 psi ( Alternatively: P = 231.0 ft × 0.4333 psi/ft = 100.09 psi ) \left(\text{Alternatively: } P = 231.0\text{ ft} \times 0.4333\text{ psi/ft} = 100.09\text{ psi}\right) ( Alternatively: P = 231.0 ft × 0.4333 psi/ft = 100.09 psi )

Worked Example 2: Complete Pumping Horsepower Cascade

Problem: A potable water booster pump delivers 1 , 800 gpm 1,800\text{ gpm} 1 , 800 gpm against a Total Dynamic Head of 220 ft 220\text{ ft} 220 ft . The pump manufacturer performance curve indicates a pump efficiency of 82.0 % 82.0\% 82.0% ( 0.82 0.82 0.82 ). The pump is driven by a high-efficiency electric motor operating at 91.0 % 91.0\% 91.0% efficiency ( 0.91 0.91 0.91 ). Calculate:

Water Horsepower (WHP).

Brake Horsepower (BHP).

Motor Horsepower / Input Electrical Horsepower (MHP).

Overall Wire-to-Water Efficiency (%).

Step 1: Calculate Water Horsepower (WHP). WHP = 1 , 800 gpm × 220 ft 3 , 960 = 396 , 000 3 , 960 = 100.0 WHP \text{WHP} = \frac{1,800\text{ gpm} \times 220\text{ ft}}{3,960} = \frac{396,000}{3,960} = \mathbf{100.0\text{ WHP}} WHP = 3 , 960 1 , 800 gpm × 220 ft ​ = 3 , 960 396 , 000 ​ = 100.0 WHP

Step 2: Calculate Brake Horsepower (BHP). BHP = WHP η pump = 100.0 WHP 0.82 = 121.95 BHP ≈ 122.0 BHP \text{BHP} = \frac{\text{WHP}}{\eta_{\text{pump}}} = \frac{100.0\text{ WHP}}{0.82} = \mathbf{121.95\text{ BHP}} \approx \mathbf{122.0\text{ BHP}} BHP = η pump ​ WHP ​ = 0.82 100.0 WHP ​ = 121.95 BHP ≈ 122.0 BHP

Step 3: Calculate Motor Horsepower (MHP). MHP = BHP η motor = 121.95 BHP 0.91 = 134.01 MHP ≈ 134.0 HP \text{MHP} = \frac{\text{BHP}}{\eta_{\text{motor}}} = \frac{121.95\text{ BHP}}{0.91} = \mathbf{134.01\text{ MHP}} \approx \mathbf{134.0\text{ HP}} MHP = η motor ​ BHP ​ = 0.91 121.95 BHP ​ = 134.01 MHP ≈ 134.0 HP

(Note: A utility engineer would specify a standard commercial 150 HP electric motor).

Step 4: Calculate overall Wire-to-Water Efficiency. η overall = 0.82 × 0.91 = 0.7462 = 74.6 % \eta_{\text{overall}} = 0.82 \times 0.91 = 0.7462 = \mathbf{74.6\%} η overall ​ = 0.82 × 0.91 = 0.7462 = 74.6% ( Verification: 100.0 WHP 134.01 MHP × 100 % = 74.62 % ) \left(\text{Verification: } \frac{100.0\text{ WHP}}{134.01\text{ MHP}} \times 100\% = 74.62\%\right) ( Verification: 134.01 MHP 100.0 WHP ​ × 100% = 74.62% )

Worked Example 3: Electrical Power Demand & Annual Energy Cost

Problem: The booster pump from Worked Example 2 ( Input Power = 134.01 HP \text{Input Power} = 134.01\text{ HP} Input Power = 134.01 HP ) runs for an average of 14.0 hours per day 14.0\text{ hours per day} 14.0 hours per day year-round. If the local municipal electric utility charges a blended energy rate of $ 0.11 per kWh \text{\textdollar}0.11\text{ per kWh} $ 0.11 per kWh , calculate:

The electrical power demand in kilowatts (kW).

The daily electrical energy consumption in kWh.

The total annual pumping electrical energy cost.

Step 1: Convert Motor Horsepower to electrical kilowatts (kW). Power (kW) = 134.01 HP × 0.746 kW/HP = 99.97 kW ≈ 100.0 kW \text{Power (kW)} = 134.01\text{ HP} \times 0.746\text{ kW/HP} = \mathbf{99.97\text{ kW}} \approx \mathbf{100.0\text{ kW}} Power (kW) = 134.01 HP × 0.746 kW/HP = 99.97 kW ≈ 100.0 kW

Step 2: Calculate daily energy consumption in kWh. Daily kWh = 99.97 kW × 14.0 hr/day = 1 , 399.58 kWh/day \text{Daily kWh} = 99.97\text{ kW} \times 14.0\text{ hr/day} = \mathbf{1,399.58\text{ kWh/day}} Daily kWh = 99.97 kW × 14.0 hr/day = 1 , 399.58 kWh/day

Step 3: Calculate daily and annual operating costs. Daily Cost = 1 , 399.58 kWh/day × $ 0.11 /kWh = $ 153.95 / d a y \text{Daily Cost} = 1,399.58\text{ kWh/day} \times \$0.11\text{/kWh} = \mathbf{\$153.95/day} Daily Cost = 1 , 399.58 kWh/day × $0.11 /kWh = $153.95/day Annual Cost = $ 153.95 / d a y × 365 days/year = $ 56 , 191.75 / y e a r ≈ $ 56 , 192 / y e a r \text{Annual Cost} = \$153.95/day \times 365\text{ days/year} = \mathbf{\$56,191.75/year} \approx \mathbf{\$56,192/year} Annual Cost = $153.95/ d a y × 365 days/year = $56 , 191.75/year ≈ $56 , 192/year

Loading diagram... Pumping System Energy & Horsepower Transformation Cascade