Study guide

9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation

Key Takeaways Explain This Topic AI

Compressed air condenses water in the receiver, so draining it prevents internal corrosion and keeps water out of instrument air lines that would freeze in unheated Colorado spaces.

A conveyor must be locked out before any clearing, adjustment, or guard removal, because reaching into a jammed screw conveyor has cost operators limbs.

A hoist used for non-entry confined space rescue must carry a personnel rating, which is different from a material handling rating.

The mechanical interlock in an automatic transfer switch makes simultaneous utility and generator connection impossible, preventing lethal backfeed onto utility lines.

Running a standby diesel repeatedly at no load causes wet stacking, so periodic testing must be under real or simulated load long enough to reach operating temperature.

Last updated: August 2026

The supporting equipment WPI lists by name

The Wastewater Treatment equipment outline closes with ancillary equipment: air compressors, conveyors, valves, hoists and cranes, pipes and fittings , and auxiliary power: generator . The Water Treatment outline lists air compressors , blowers , emergency systems , and power generation systems , and the collection outline lists chain pull hoists and overhead cranes and fans (forced air, air extraction) . This section covers that supporting equipment.

Air compressors

Plant air does more work than most operators realize: it operates pneumatic valve actuators and instruments , supplies air scour and bubbler level systems , drives air-operated diaphragm pumps , powers tools , and provides air for blow-down and cleaning .

Type Principle Notes

Reciprocating (piston) Piston compresses air in a cylinder Common in small plants; single or two stage; needs a receiver

  • Rotary screw Meshing helical rotors Continuous duty, quieter, higher capacity
  • Rotary vane Sliding vanes in an offset rotor Compact, moderate duty
  • Centrifugal High-speed impeller Large constant-duty applications

Operating essentials:

Drain the receiver. Compressing air condenses water, which collects in the tank. Water in the receiver causes internal corrosion and carries into instrument air lines where it destroys positioners and freezes in cold weather. Automatic drains are installed and their operation is verified; manual drains are opened daily.

Air dryers and filters. Instrument air requires a refrigerated or desiccant dryer to reach a dew point below the coldest ambient temperature the lines will see. In Colorado, an instrument air line running through an unheated gallery will plug with ice if the dryer fails.

Safety relief valve. A receiver is a pressure vessel. The relief valve is tested, never blocked or adjusted upward, and the receiver is inspected per code.

Inlet filter cleanliness directly affects capacity and energy use.

Unloading and cycling. Compressors that cycle continuously are oversized or the system is leaking. Compressed air leaks are the most expensive utility leak in a plant, because the energy to make the air is many times the value of the air itself.

Never use compressed air to clean clothing or skin. Air injected under the skin causes embolism.

Conveyors, hoists, and cranes

Conveyors move screenings, grit, and dewatered cake. Belt, screw (auger), and shaftless screw designs are common. Guarding at nip points is mandatory, and a conveyor is a machine that must be locked out before any clearing, adjustment, or guard removal — reaching into a jammed screw conveyor has cost operators limbs.

Hoists and cranes are listed by WPI in both the treatment and collection outlines because operators routinely lift submersible pumps, mixers, and screen assemblies. Requirements:

Rated capacity marked on the hoist and never exceeded, and load ratings for slings and hardware known.

Periodic inspection of hooks (for throat opening and twist), chains and wire rope (for broken wires, kinks, and corrosion), brakes, and limit switches, with records.

Never work or walk under a suspended load , and use tag lines to control it.

Portable davit and jib arms at lift stations must be installed in a base rated for the load, and the base itself inspected.

Retrieval-rated equipment for confined space rescue is a different rating than material handling; a hoist used for non-entry rescue must be rated for personnel.

Valves and piping

Beyond the process valves covered elsewhere, plant service piping includes air, water, chemical, and sludge lines. Practical items:

Label and color-code every line by contents and direction of flow so no one guesses.

Sludge lines need cleanouts, generous radius bends, and provision for flushing; they plug.

Chemical lines need double containment or containment routing where a leak would be hazardous.

Expansion provisions on hot blower discharge piping.

Freeze protection on any line that can sit stagnant in an unheated space.

Standby power

Auxiliary power is listed as its own equipment item, and for good reason: a wastewater plant or lift station without power spills, and a water plant without power loses pressure and its disinfection barrier.

Components: the engine-generator set, the fuel system , the automatic transfer switch (ATS) , load banks or shed logic, and cooling and exhaust.

Automatic transfer switch operation is the concept most often tested. On loss of utility power the ATS senses the failure, waits a short confirmation delay, signals the generator to start, waits for the generator to reach rated voltage and frequency, then transfers the load. On restoration of utility power it waits a longer stabilization delay, transfers back, and runs the generator unloaded for a cool-down period before shutting it down. A properly interlocked transfer switch makes it physically impossible to connect the generator to the utility , which prevents backfeeding — energizing a supposedly dead utility line and killing a lineworker.

Exercise and testing. A generator that has never run under load is not standby power. Standard practice is a weekly no-load or brief run plus a monthly or quarterly test under real or simulated load long enough to reach operating temperature. Running a diesel repeatedly at no load causes wet stacking , the accumulation of unburned fuel in the exhaust, which fouls injectors and turbochargers.

Fuel management. Diesel degrades and grows microbial contamination at the fuel-water interface. Tanks are kept full to limit condensation, treated with biocide and stabilizer, tested periodically, and polished or turned over on a schedule. Day tanks and their level alarms are checked, and fuel supply for an extended outage — Colorado blizzards and wildfires have produced multi-day outages — is part of the emergency response plan.

Routine checks: coolant and oil level, block heater operation (critical in Colorado winters), battery condition and charger operation, belts and hoses, air intake, exhaust integrity and carbon monoxide risk in enclosed spaces, fuel level, and the run-hours log.

Loading diagram... Ancillary Equipment and Standby Power