Study guide
4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation
Colorado Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: State Laws, Regulations & CCWP Certification
1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting
2 Chapter 2: Source Water & Drinking Water Treatment Processes
2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle
3 Chapter 3: Disinfection & Chemical Addition
3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices
4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance
4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management
5 Chapter 5: Wastewater Treatment Principles & Biological Processes
5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects
6 Chapter 6: Advanced Wastewater Treatment & Solids Management
6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84
7 Chapter 7: Water Distribution Systems
7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems
8 Chapter 8: Wastewater Collection Systems
8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment
9 Chapter 9: Pumps, Motors & Utility Mechanics
9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control
10 Chapter 10: Laboratory Analysis & Water Quality Monitoring
10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)
11 Chapter 11: Operator Mathematics & Applied Calculations
11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance
12 Chapter 12: Safety, Emergency Operations & Compliance
12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties
4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation
Key Takeaways Explain This Topic AI
All-vacuum gas chlorination places the vacuum regulator on the container so that any downstream line break draws air in and closes the regulator instead of releasing gas.
Chlorine gas is about 2.5 times heavier than air, so chlorine rooms are at grade with floor-level ventilation, exterior access, a door window, and the ventilation switch outside.
A ton container's upper valve withdraws gas and the lower valve withdraws liquid, and continuous gas withdrawal above roughly 400 lbs per day per ton container causes frosting and feed loss.
Sodium hypochlorite loses strength with heat, light, and time, raises treated water pH, off-gasses oxygen, and generates chlorate as it decomposes.
Onsite hypochlorite generation produces about 0.8 percent product and liberates explosive hydrogen, so forced dilution ventilation and cell acid cleaning are the defining operating requirements.
Last updated: August 2026
Three ways to put chlorine in water
Regulation 100 classifies gas chlorine , onsite hypochlorite generation , and sodium or calcium hypochlorite as separate treatment types with different facility classes, because the equipment and the hazards genuinely differ. WPI's Equipment Operation and Maintenance outline lists the "chlorine disinfection system" as an inspect, maintain, and operate item. This section is about the hardware; the chemistry and CT calculations appear in the disinfection chapter.
Gas chlorine systems
Chlorine gas is shipped as a liquefied gas under pressure in 150-pound cylinders and 1-ton containers. Because chlorine gas is about 2.5 times heavier than air , a release settles into low areas: basements, pits, trenches, and valve vaults. That single fact governs the entire building design.
The vacuum principle
Modern systems are all-vacuum downstream of the container, and this is the most important safety concept in the subject. A vacuum regulator mounted directly on the container valve holds the gas at pressure only inside the container. Everything past the regulator, including all the tubing running through the plant, is under vacuum created by the ejector . If a vacuum line breaks, air is drawn in and the regulator closes , so no gas escapes. Pressurized gas piping outside the chlorine room is not acceptable practice.
The flow path is:
Container valve with a fusible plug that melts near 158 to 165 degrees Fahrenheit to relieve pressure in a fire.
Vacuum regulator / pressure-reducing valve , with an inlet lead gasket that is replaced at every container change.
Rotameter and rate valve , manual or automatic.
Ejector (injector) , where a motive water stream through a venturi creates the vacuum and dissolves the gas.
Diffuser at the application point.
Withdrawal rates and reevaporation
Chlorine withdrawn as a gas absorbs heat of vaporization from the liquid, chilling the container. Exceeding the withdrawal rate causes frosting , then a falling withdrawal rate, then loss of feed. Rule-of-thumb maximum continuous gas withdrawal at about 70 degrees Fahrenheit is roughly 40 lbs per day per 150-lb cylinder and 400 lbs per day per ton container . Larger demands require liquid withdrawal through an evaporator , which supplies external heat. Never apply direct heat, torches, or steam to a container.
A ton container has two valves on the end, arranged vertically when properly positioned: the upper valve draws gas , the lower valve draws liquid . Orienting the container so the valves are one above the other is not cosmetic; it determines what you get.
Chlorine room requirements
Located at grade with direct exterior access , never below grade.
Ventilation at floor level , roughly one complete air change per minute, with the switch outside the door and a window in the door so you can look in before entering.
Gas detection with audible and visual alarm inside and outside the room.
Separate room from the ejector, controls, and other chemical storage; never store ammonia in the same room .
Emergency repair kits : Kit A for 150-lb cylinders, Kit B for ton containers, Kit C for tank cars.
Self-contained breathing apparatus stored outside the chlorine room, inspected monthly, with trained users.
Containers secured upright with chains, and valve protection hoods in place whenever not connected.
Leak detection with a household ammonia solution on a swab, which produces a white cloud of ammonium chloride at a leak. Never use water , because chlorine plus moisture forms hydrochloric and hypochlorous acids that accelerate corrosion and make the leak worse.
Facilities storing chlorine gas above threshold quantities also fall under the EPA Risk Management Program and OSHA Process Safety Management , and under the America's Water Infrastructure Act risk and resilience assessment requirements.
Sodium hypochlorite
Liquid bleach at 10 to 15 percent available chlorine is the most common alternative and eliminates the toxic gas hazard entirely. It brings its own problems:
It decomposes. Strength falls with time, heat, light, and metal contamination. Decomposition roughly doubles for each 18 degrees Fahrenheit rise. Product delivered at 12.5 percent may be 10 percent within weeks in a hot room. Store cool, dark, and turn over inventory , and test the strength of what you actually have rather than what the label says.
It off-gasses oxygen , causing vapor lock in feed pumps. Tanks need vents; feed pumps need degassing heads or peristaltic designs.
It raises pH. Sodium hypochlorite is strongly alkaline, so it raises the treated water pH, which reduces the fraction of disinfectant present as hypochlorous acid and therefore reduces disinfection efficiency at a given residual.
Decomposition produces chlorate , an emerging contaminant of concern that increases with storage time, temperature, and higher product strength.
It is corrosive and reacts violently with acid. Dedicated containment, dedicated fill connections, and PPE at every connection break.
Calcium hypochlorite is a dry solid at about 65 to 70 percent available chlorine, supplied as granules or tablets. It stores far longer than liquid, but it is a powerful oxidizer : contact with organic material, oil, grease, or rags can start a fire, and contact with even small amounts of water in a closed container can generate heat and gas. Store it dry, separate from organics and acids, in its original container.
Onsite hypochlorite generation
An onsite generation (OSG) system electrolyzes a brine solution to produce a dilute sodium hypochlorite of roughly 0.8 percent available chlorine. Because there is no shipment or storage of hazardous chlorine, OSG removes the gas hazard and the strength-decay problem of bulk bleach.
Components are a water softener (essential, because hardness scales the electrolytic cell), a brine tank and saturator , a rectifier converting AC to low-voltage DC, the electrolytic cell , a hypochlorite storage tank , and hydrogen dilution and venting .
Two operational realities dominate:
Hydrogen gas is a by-product. Electrolysis of brine liberates hydrogen, which is explosive between roughly 4 and 75 percent in air. The system must have forced dilution air and continuous venting to the outside , with no ignition sources and interlocks that stop generation on ventilation failure. Hydrogen accumulation in an OSG room is the principal hazard of the technology.
The cell must be acid cleaned. Even with softening, calcium and magnesium scale accumulates on the electrodes and reduces output. Periodic acid cleaning per the manufacturer's procedure restores capacity, and falling output at constant current is the indicator.
Because the product is only about 0.8 percent, the volume fed is roughly 15 times that of 12.5 percent bulk bleach, so feed pumps and piping are correspondingly larger.
Comparing the three
- Gas chlorine Sodium hypochlorite Onsite generation
- Strength 100 percent 10 to 15 percent about 0.8 percent
- Effect on pH Lowers pH slightly Raises pH Slight
- Principal hazard Toxic gas release Corrosive liquid, chlorate Hydrogen gas
- Storage stability Indefinite Degrades in weeks Generated on demand
- Regulatory burden RMP, PSM, SCBA, repair kits Containment, PPE Electrical, ventilation
- Reg 100 class at less than 350 gpm C D C
Whichever system a plant uses, the operator's daily checks are the same in spirit: verify the residual being produced, verify the feed equipment is delivering the rate it is set to, verify the safety systems (ventilation, detection, alarms, SCBA, eyewash) are functional, and record what you found.