Study guide
4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation
Colorado Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: State Laws, Regulations & CCWP Certification
1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting
2 Chapter 2: Source Water & Drinking Water Treatment Processes
2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle
3 Chapter 3: Disinfection & Chemical Addition
3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices
4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance
4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management
5 Chapter 5: Wastewater Treatment Principles & Biological Processes
5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects
6 Chapter 6: Advanced Wastewater Treatment & Solids Management
6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84
7 Chapter 7: Water Distribution Systems
7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems
8 Chapter 8: Wastewater Collection Systems
8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment
9 Chapter 9: Pumps, Motors & Utility Mechanics
9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control
10 Chapter 10: Laboratory Analysis & Water Quality Monitoring
10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)
11 Chapter 11: Operator Mathematics & Applied Calculations
11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance
12 Chapter 12: Safety, Emergency Operations & Compliance
12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties
4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation
Key Takeaways Explain This Topic AI
A PLC executes control logic locally while SCADA supervises, archives, and displays, so a well-designed plant keeps running on local logic when SCADA communication is lost.
The 4 to 20 milliamp standard uses a live zero so that a broken wire reads 0 mA and is recognized as a fault rather than as a valid zero measurement.
Compound loop control combines flow pacing with residual feedback trim, which is why it is the standard arrangement for disinfection.
Chemical usage expressed as pounds per million gallons is the honest efficiency metric because it normalizes for changes in plant flow.
Operating log errors are corrected with a single line through the entry plus the correct value, initials, and date, never by erasing, and falsifying records is grounds for certificate revocation under Regulation 100 section 100.13.
Last updated: August 2026
Process control is a job task, not a philosophy
The WPI Treatment Process outline is unusually explicit about control and records. It requires operators to interact with SCADA systems including data communication integration, PLC programming and maintenance, and the human machine interface; to determine and adjust plant flows to meet system demands; to troubleshoot malfunctions in plant process and equipment; to identify trends and abnormal operation by interpreting data from gauges, meters, charts, and graphs; to maintain records of operation including laboratory results, equipment logs, intake and production, maintenance management reports, and water quality sampling results; and to make appropriate changes in plant processes to optimize performance and efficiency.
The control hierarchy
Layer What it is Operator's relationship
Field devices Sensors and final control elements: turbidimeters, chlorine analyzers, pressure and level transmitters, flow meters, valve actuators, VFDs Calibrate, verify, and replace
PLC (programmable logic controller) Ruggedized industrial computer running the control logic in a scan cycle; executes interlocks and sequences Understand the logic; know what each interlock does
HMI (human machine interface) Operator-facing graphic screens, alarms, setpoints, trends Daily working surface
SCADA (supervisory control and data acquisition) The system that collects data from all PLCs and remote sites, archives it as a historian, and presents it Trending, reporting, remote sites
Telemetry / RTU Radio, cellular, fiber, or leased line links to remote tanks, wells, and lift stations Verify communication health
The essential distinction for the exam: a PLC executes control , while SCADA supervises, collects, and displays . If communication to SCADA is lost, a properly designed PLC keeps the plant running on local logic. If the PLC fails, the process stops or falls back to manual.
Analog signals are usually 4 to 20 milliamps , where 4 mA is zero and 20 mA is full scale. Choosing 4 mA rather than 0 mA as the zero point is deliberate: a broken wire reads 0 mA, which the system recognizes as a fault rather than as a legitimate zero. Discrete signals are simple on/off contacts. Loop calibration verifies the whole path, from the sensed value through the transmitter, wiring, and input card to the number displayed on the HMI.
Control modes
Manual. The operator sets the output directly.
Flow-paced. Chemical feed is slaved to plant flow so dose in mg/L stays constant as flow changes. This is the default for coagulant and fluoride.
Residual (feedback) control. A chlorine analyzer measures the residual and the controller trims the feed to hold a setpoint. Feedback alone reacts slowly because of transport delay.
Compound loop. Flow pacing sets the base feed and residual feedback trims it. This is the standard for disinfection because it combines fast feed-forward with accurate correction.
Cascade and ratio control for interlinked processes.
A PID controller acts on proportional (present error), integral (accumulated error), and derivative (rate of change) terms. Operators rarely retune loops but must recognize the symptoms: a loop that hunts and oscillates usually has too much gain or too little integral time; a loop that drifts and never reaches setpoint has too little gain or a stuck final element.
Alarm management
Alarms only work if they mean something. Practical rules:
Every alarm should have a defined operator response . An alarm with no action is noise.
Distinguish priority levels — critical (loss of disinfection, turbidity exceedance, tank overflow), high, and advisory.
Alarm flooding during an upset — dozens of alarms at once — hides the initiating event. Grouping and suppression logic exist for this.
Deadbands and time delays prevent chatter from a sensor sitting at the threshold.
Critical alarms need independent hardwired backup where practical, not just a SCADA point: a low chlorine residual alarm that depends on the same failed analyzer is worthless.
Alarm response must be documented , because a regulator reviewing an exceedance will ask when the alarm annunciated and what was done.
Cyber security
The WPI Security, Safety, and Administrative Procedures outline lists "perform cyber security according to industry standards." Water utilities have been the target of real intrusions, several through remote access on control systems. Baseline expectations:
Segment the control network from the business network and from the internet; no direct internet exposure of PLCs or HMIs.
Remove default passwords and use unique credentials per person, never a shared operator login.
Multi-factor authentication on all remote access, and remove access immediately when staff leave.
Patch HMI and historian workstations; keep an offline, tested backup of PLC programs and HMI configurations .
Control removable media ; USB drives are a common infection path.
Assume manual operation may be necessary. Every plant should be able to run on local control and manual valves. This is also required thinking under the America's Water Infrastructure Act risk and resilience assessment and emergency response plan.
Trending: reading the plant, not the snapshot
Identifying trends and abnormal operation by interpreting gauges, meters, charts, and graphs is a listed job task, and it is the skill that separates an operator from a button-pusher. A single reading tells you a value; a trend tells you a direction and a rate .
Trends worth watching daily:
Filter headloss versus run time — a steepening slope means the coagulant dose or raw quality has changed.
Individual filter effluent turbidity per run — the ripening peak height and the end-of-run tail.
Chlorine demand , computed as dose minus residual, which rises with organics, ammonia, temperature, and biofilm.
Raw versus settled turbidity , the direct measure of pretreatment performance.
Clearwell level versus production and demand , which shows whether the plant rate matches the system.
Motor amperage and pump discharge pressure for each pump, which drift before they fail.
Chemical usage in pounds per million gallons , which is the honest efficiency metric and normalizes for flow.
A worked example of trend reading: over three weeks, filter run length falls from 60 hours to 34 hours, raw turbidity is unchanged, but settled turbidity has risen from 1.1 to 2.4 NTU and alum usage is unchanged. Because settled water has degraded while raw water and dose are steady, the problem is in coagulation chemistry rather than in the filters. A likely cause is a change in raw water pH or alkalinity moving the coagulation out of its optimum range, and the diagnostic step is a jar test across pH , not a longer backwash.
Records of operation
Records are both a regulatory obligation and the raw material for troubleshooting. A complete plant record set includes:
Daily operating log — flows, levels, chemical doses and usage, residuals, turbidity, pH, temperature, staff on duty, and narrative notes on anything unusual.
Laboratory bench sheets — raw data with analyst initials, date, time, method, and instrument identification, retained as the source behind reported values.
Equipment logs and work orders — runtime hours, maintenance performed, parts installed, calibration results.
Intake and production records — raw water withdrawn and finished water produced, which also supports water rights accounting in Colorado.
Water quality sampling results — with sample siting plan, chain of custody, and laboratory reports.
Monthly reports to CDPHE , submitted for drinking water systems by the deadline in Regulation 11.
Maintenance management reports and notes.
Three rules govern all of them. Record at the time of the observation , not later from memory. Never erase or overwrite : correct an error with a single line through it, the correct value, your initials, and the date. And record what actually happened , including the upset, because falsifying an operating record is a criminal act under Colorado law and is grounds for revocation of your certificate under Regulation 100 section 100.13.