Study guide

5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc

Key Takeaways Explain This Topic AI

Sludge bulking is characterized by an SVI > 150–200 mL/g, triggered either by filamentous overgrowth (low DO, low F/M, nutrient deficiency, low pH, or septic sulfides) or non-filamentous zoogloeal slime overproduction.

Emergency filamentous bulking control is achieved via targeted RAS chlorination at 2 to 5 lb Cl2 per 1,000 lb MLSS-day directly into the RAS line, selectively destroying exposed filament sheaths without lysing floc cores.

Nocardioform and Microthrix parvicella foaming generates thick, brown, greasy foam fueled by high MCRT, elevated FOG, and warm temperatures, remedied by increasing WAS rates, eliminating scum recycling, and applying surface hypochlorite sprays.

Rising sludge in secondary clarifiers is caused by biological denitrification (NO3- reduced to N2 gas bubbles lifting settled blankets), distinguished from bulking by rapid initial settling followed by floating within 1–2 hours; remedied by increasing RAS rates.

Young sludge manifests as white billowy foam and straggler floc (high F/M, low MCRT), whereas old sludge exhibits pin floc, ashing, and dark greasy foam (low F/M, high MCRT).

Last updated: August 2026

Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc

Activated sludge is a dynamic biological ecosystem vulnerable to chemical, hydraulic, and microbiological upsets. When an upset occurs, secondary clarifiers lose solids separation capability, resulting in severe permit violations for Total Suspended Solids (TSS), Biochemical Oxygen Demand (BOD), and nutrients. A certified operator in responsible charge must possess the diagnostic acuity to rapidly distinguish between filamentous bulking, non-filamentous zoogloeal slime, biological foaming, denitrification rising sludge, and pin floc, implementing precise corrective interventions.

1. Activated Sludge Troubleshooting Master Matrix +---------------------------------------------------------------------------------------------------------+

  • | ACTIVATED SLUDGE UPSET DIAGNOSTIC MATRIX |
  • +---------------------------------------------------------------------------------------------------------+
  • | Symptom / Observation | SVI Range | Microscopic Diagnosis | Primary Cause | Corrective Action |

+-------------------------+--------------+-----------------------------+---------------------+-------------------------+

| Filamentous Bulking | > 150-300+ | Filaments bridging between | Low DO, low F/M, | Identify trigger; |

| (Slow settling blanket) | mL/g | flocs (S. natans, Type 021N)| low N/P, septic H2S | RAS Cl2 @ 2-5 lb/1k lb |

  • | Zoogloeal Bulking | > 200 mL/g | Amorphous slime jelly; | High soluble BOD | Balance N & P nutrients |
  • | (Viscous, jelly-like) | | excessive bound EPS water | with severe N/P def.| (target 100:5:1 BOD:N:P)|
  • | Nocardia Foaming | Variable | Actinomycetes branching | High MCRT, high | Increase WAS; skim scum;|
  • | (Thick brown foam) | (80-150) | filaments with waxy walls | FOG, warm water | surface Cl2 spray |
  • | Young Sludge Foam | Normal to | Flagellates & amoebae; | Low MCRT (<2 d), | Decrease WAS; build up |
  • | (White, billowy foam) | High | small, weak loose floc | high F/M (>0.5) | MLSS inventory |
  • | Rising Sludge | Normal SVI | Stalked ciliates; settled | Denitrification in | Increase RAS rate; |

| (Clumping after settle) | (<120 mL/g) | sludge floats after 1-2 hr | clarifier (NO3->N2) | reduce aerator DO |

  • | Pin Floc / Ashing | < 80 mL/g | Rotifers & nematodes; | Old sludge (high | Increase WAS; reduce |
  • | (Hazy, tiny floc specks)| | tiny, dense sheared flocs | MCRT), over-aeration| aeration turbulence |
  • +---------------------------------------------------------------------------------------------------------+
  • 2. Filamentous and Non-Filamentous Sludge Bulking

Sludge Bulking occurs when mixed liquor suspended solids fail to compact and settle cleanly in secondary clarifiers, leading to high sludge blankets and solids washout over effluent weirs ( S V I > 150 to 300 + mL/g SVI > 150\text{ to }300+\text{ mL/g} S V I > 150 to 300 + mL/g ). Microscopic Architecture of Settling Floc:

Healthy Floc (SVI 80-150): Filamentous Bulking (SVI > 200):

  • +-----------------------+ +--------------------------------+
  • | ( Bacterial ) | | --\--- ( Bacterial ) --/---- | <-- Long filaments
  • | ( Colonies ) | | --- ( Colonies ) ----- | extend into bulk
  • | [Moderate Filaments] | | --/--- [ Overgrowth] --\---- | liquid, bridging
  • +-----------------------+ +--------------------------------+ and preventing
  • (Tightly knitted matrix) (Diffuse, loose, uncompactable) compaction
  • Filamentous Bulking Triggers and Identifiers

Filamentous bacteria provide the structural backbone for floc; however, when environmental conditions favor filaments over floc-forming bacteria, filaments extend outward into the bulk liquid, physically preventing flocs from consolidating:

Low Dissolved Oxygen ( D O < 1.5 mg/L DO < 1.5\text{ mg/L} D O < 1.5 mg/L ) : Sphaerotilus natans , Type 1701 , Haliscomenobacter hydrossis .

Low Food-to-Microorganism Ratio ( F / M < 0.15 day − 1 F/M < 0.15\text{ day}^{-1} F / M < 0.15 day − 1 ) : Type 0041 , Type 0675 , Type 0092 (organisms adapted to scavenge ultra-low substrate concentrations).

Nutrient Deficiency (Nitrogen or Phosphorus) : Type 021N , Thiothrix I & II ( B O D 5 : N : P < 100 : 5 : 1 BOD_5 : N : P < 100 : 5 : 1 BO D 5 ​ : N : P < 100 : 5 : 1 ).

Septic Influent / High Sulfides ( H 2 S H_2S H 2 ​ S ) : Thiothrix , Beggiatoa , Type 021N (contain intracellular sulfur granules visible under phase-contrast microscopy).

Low Aeration pH ( p H < 6.5 pH < 6.5 p H < 6.5 ) : Fungal overgrowth ( Geotrichum , yeasts).

Non-Filamentous (Zoogloeal / Viscous) Bulking

Non-filamentous bulking is caused by floc-forming bacteria ( Zoogloea ramigera ) overproducing vast quantities of hydrated Extracellular Polymeric Substances (EPS) (mucilage or bio-slime). The excessive bound water gives the mixed liquor a jelly-like consistency that will not settle or dewater. It is triggered by high concentrations of readily biodegradable soluble sugars paired with severe nitrogen or phosphorus starvation.

Emergency Remediation: RAS Chlorination Protocol

While identifying and correcting the underlying operational cause is mandatory for long-term control, severe bulking with imminent solids washout requires emergency RAS chlorination : Daily Chlorine Dose (lb C l 2 /day) = Dosage (2 to 5 lb C l 2 ) 1 , 000 lb MLSS × Total System MLSS Mass (1,000 lbs) \text{Daily Chlorine Dose (lb } Cl_2\text{/day)} = \frac{\text{Dosage (2 to 5 lb } Cl_2\text{)}}{1,000\text{ lb MLSS}} \times \text{Total System MLSS Mass (1,000 lbs)} Daily Chlorine Dose (lb C l 2 ​ /day) = 1 , 000 lb MLSS Dosage (2 to 5 lb C l 2 ​ ) ​ × Total System MLSS Mass (1,000 lbs)

Injection Point : Chlorine (sodium hypochlorite or chlorine gas) must be injected directly into the RAS pipeline or at the point where RAS discharges into the aeration basin inlet. This ensures high local chlorine concentration where filaments protruding from the floc are selectively destroyed.

Target Dosing : 2.0 to 5.0 lbs of C l 2 Cl_2 C l 2 ​ per 1,000 lbs of MLSS in the total system inventory per day .

Frequency of Exposure : The entire system biomass inventory should pass the chlorination point 2 to 3 times per day (governed by the RAS recycle rate).

Monitoring : Microscopic examination must be conducted daily. Dosing must cease immediately once filament sheaths are empty or fragmented. Over-chlorination causes deflocculation, milky-white effluent turbidity, and complete destruction of autotrophic nitrifiers.

3. Biological Foaming: Nocardia vs. Young Sludge Foam +-----------------------------------------------------------------------------------------+

  • | BIOLOGICAL FOAM COMPARISON MATRIX |
  • +-----------------------------------------------------------------------------------------+
  • | Foam Property | Nocardioform / Microthrix Foam | Young Sludge / Surfactant Foam|
  • +---------------------+------------------------------------+-------------------------------+
  • | Visual Appearance | Thick, viscous, dark tan/chocolate | Light, billowy, white, soapy, |
  • | | brown; stable, greasy crust | frothy; collapses easily |
  • | Sludge Age (MCRT) | High MCRT (typically > 8 to 15 d) | Low MCRT (< 1 to 3 days) |
  • | Organic Loading F/M | Low F/M (< 0.2 day⁻¹) | High F/M (> 0.5 day⁻¹) |
  • | Primary Cause | High FOG; mycolic acid cell walls; | Detergents, plant startup, |
  • | | recycling clarifier scum | severe hydraulic washout |
  • | Corrective Action | Increase WAS; skim & discard foam; | Decrease WAS; build up MLSS |
  • | | spray 50 mg/L Cl2 surface solution | inventory; apply water sprays |
  • +-----------------------------------------------------------------------------------------+
  • Nocardioform Actinomycetes Foaming

Nocardia , Gordonia , and Microthrix parvicella possess hydrophobic cell walls packed with mycolic acids (waxy lipids). These bacteria attach to air bubbles generated by fine-bubble diffusers and float to the surface, forming a persistent, thick, chocolate-brown grease layer that covers aeration basins and secondary clarifiers:

Eliminating Scum Recycling : Surface scum contains billions of viable Nocardia cells per milliliter. Never recycle skimmer scum to the head of the plant . Scum must be physically harvested and hauled for disposal.

Surface Spray Chlorination : Spraying a dilute chlorine solution ( 50 to 100 mg/L free C l 2 Cl_2 C l 2 ​ ) directly onto the aeration surface foam layer chemically oxidizes actinomycetes without intoxicating the sub-surface mixed liquor.

4. Rising Sludge (Secondary Clarifier Denitrification)

Rising Sludge is a physical phenomenon where sludge settles properly in the secondary clarifier but subsequently floats to the surface in large sheets or clumps within 1 to 4 hours. The Denitrification Flotation Mechanism:

  • Aeration Basin: NH4+ (Ammonia) + 2 O2 ---> NO3- (Nitrate) [Biological Nitrification]
  • |
  • v
  • Secondary Clarifier: [ Thick Sludge Blanket ] (DO drops to 0.0 mg/L)
  • Facultative Heterotrophs reduce NO3- ---> N2 (Insoluble Nitrogen Gas)
  • |
  • v
  • N2 gas bubbles attach to floc ---> Sludge blanket floats to surface
  • Diagnostic Distinction from Bulking

The Settleometer Test : In a 30-minute settleometer test, rising sludge displays excellent initial settling ( S S V 30 SSV_{30} SS V 30 ​ yields a healthy S V I < 120 mL/g SVI < 120\text{ mL/g} S V I < 120 mL/g ). However, after 45 to 120 minutes of standing quiescently on the laboratory bench, the entire settled sludge mass floats to the top of the cylinder propelled by tiny rising nitrogen gas bubbles.

Bulking Sludge : Fails to settle from the start ( S V I > 200 mL/g SVI > 200\text{ mL/g} S V I > 200 mL/g ) and does not require gas flotation to remain suspended.

Operational Remedies for Rising Sludge

Increase RAS Pumping Rate : Accelerate the return rate to evacuate settled solids from the clarifier floor before the blanket detention time exceeds 1.5 to 2.0 hours .

Reduce Aeration Basin DO : If nitrification is not required by the plant permit, lower aeration basin DO to < 1.5 mg/L < 1.5\text{ mg/L} < 1.5 mg/L to suppress autotrophic nitrifiers and reduce effluent nitrate concentrations.

Upstream Anoxic Zone : Create an un-aerated anoxic selector basin ahead of the aeration tank to denitrify recycled nitrates into nitrogen gas safely within the biological train before reaching the clarifier.

5. Pin Floc, Straggler Floc, and Ashing

Pin Floc (Pin-Point Floc) : Tiny, dense, discrete spherical particles (1/32 to 1/16 inch) that settle rapidly to the bottom of a settleometer but leave a turbid, hazy supernatant. Pin floc is caused by old sludge (high MCRT, very low F/M) where starved bacteria undergo endogenous decay, combined with excessive aeration turbulence shearing the fragile flocs. Remedy : Increase WAS rate to lower sludge age, and reduce aeration blower output.

Straggler Floc : Large, fluffy, loose, buoyant, feathery floc particles floating in the upper water column. Caused by young sludge (low MCRT, high F/M) with incomplete bio-flocculation. Remedy : Decrease WAS rate to increase biomass maturity.

Ashing : A fine, dusty, gray-brown floating particulate film on the surface of secondary clarifiers. Caused by low-level denitrification in old sludge or high concentrations of floating dead cell debris. Remedy : Optimize surface skimmer operation and increase daily wasting.

  • 6. Toxic Shock Loads and Hydraulic Storm Washouts
  • Toxic Shock Protocols

When industrial chemical slugs (heavy metals, high solvents, extreme acidic/caustic pH, or cyanides) enter the biological train:

Diagnostic Symptoms : Specific Oxygen Uptake Rate (SOUR) plunges by > 50%; DO in the aeration tank spikes sharply (microbes stop breathing); protozoa round up, cease ciliary movement, and die; effluent turns turbid and milky.

Immediate Corrective Actions : Divert incoming flow to emergency equalization basins; isolate healthy offline aeration trains; increase RAS recycle from un-impacted clarifiers; add supplemental powdered activated carbon (PAC) if organic toxins are suspected; re-seed the aerator with healthy mixed liquor from a neighboring utility.

Peak Wet-Weather Hydraulic Washout (Step Feed Aeration)

During severe snowmelt runoff or tropical storm inflow and infiltration (I&I), secondary clarifier surface overflow rates can exceed 2,500 gpd/sq ft , risking the complete loss of the plant's biomass inventory over the effluent weirs. Normal Plug Flow Mode: Raw Feed ===> [ Pass 1 ] ===> [ Pass 2 ] ===> [ Pass 3 ] ===> Clarifier

  • ^ (High Solids Loading to Clarifier)
  • |--- RAS
  • Step Feed Storm Mode: Raw Feed ------+-------------> [ Pass 2 ]
  • +---------------------------> [ Pass 3 ]
  • RAS =========> [ Pass 1 ] (Stores 70% of Plant Biomass under Low Flow)

Step Feed Mode : The operator diverts raw influent wastewater away from the head of the basin, introducing it directly into Pass 2 or Pass 3. RAS continues entering Pass 1 alone. This operating mode shifts 60% to 75% of the total biomass inventory into Pass 1 (acting as a concentrated biological storage reactor under zero raw flow), dramatically reducing the solids loading rate (SLR) applied to the secondary clarifier and preventing clarifier blanket washout.

Loading diagram... Activated Sludge Troubleshooting Decision Tree