Study guide

8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

Key Takeaways Explain This Topic AI

A gravity sewer is a partially full open channel, so flow requires both a depth measurement and a velocity measurement combined as Q equals A times V.

Weirs and flumes only work under free-discharge conditions, so downstream submergence invalidates the depth-to-flow relationship entirely.

Parshall flumes are preferred in wastewater because they are self-cleaning, while the pool behind a weir plate silts in and changes the approach conditions.

A sharp flow peak that tracks rainfall closely indicates inflow, while a broad delayed rise persisting for days indicates infiltration from a rising groundwater table.

Gravity capacity from Manning's equation varies with the square root of slope, and a circular pipe carries its maximum flow at about 93 percent of full depth rather than exactly full.

Last updated: August 2026

Measuring flow in a pipe that is not full

WPI's Collection System Monitoring, Evaluation, and Adjustment content area is 14 percent of the Class I exam and opens with flow monitoring , and it separately lists monitor flow sensors and calibrate and adjust atmosphere testers . Collection flow monitoring is harder than pressure-pipe metering because a gravity sewer is a partially full open channel : to know the flow you must know both the depth and the velocity .

Area-velocity metering

The governing relation is continuity: Q = A x V .

Area is computed from the measured depth and the known pipe geometry.

Velocity is measured directly, most commonly by Doppler ultrasonic , which reflects sound off particles and bubbles in the flow and reads the frequency shift.

Depth is measured by submerged pressure transducer , downward-looking ultrasonic , or radar .

Area-velocity meters work in surcharged and backwater conditions where a depth-only device would be badly wrong, which is why they dominate sewer system evaluation surveys.

Worked example. A 15-inch sewer is flowing at a depth of 6.0 inches with a measured velocity of 2.4 ft/s. From a circular-pipe table, a d/D ratio of 6/15 = 0.40 corresponds to a flow area of about 0.374 of the full-pipe area .

  • Full pipe area = 0.785 x (15/12)² = 0.785 x 1.5625 = 1.227 sq ft
  • Flow area = 0.374 x 1.227 = 0.459 sq ft
  • Q = 0.459 sq ft x 2.4 ft/s = 1.10 cfs
  • In gpm: 1.10 x 448.8 = 494 gpm , or about 0.71 MGD
  • Primary devices: weirs and flumes

Where a permanent, accurate measurement is needed, a primary device creates a known depth-to-flow relationship, and only depth has to be measured.

Device Characteristics

Parshall flume Self-cleaning, low head loss, handles solids well; the standard for wastewater influent and effluent

  • Palmer-Bowlus flume Fits inside an existing manhole or pipe; used for temporary collection monitoring
  • V-notch (triangular) weir Very accurate at low flows ; head rises rapidly with flow
  • Rectangular weir Wider range; less sensitive at low flow
  • Cipolletti (trapezoidal) weir Trapezoidal, side slopes 4 vertical to 1 horizontal

Two rules govern weirs and flumes and both are commonly tested. First, the device must discharge freely ; if downstream water backs up and submerges the device, the depth-to-flow relationship is invalid and the reading is meaningless. Second, head is measured upstream of the crest or throat at the specified distance , not at the crest itself. For weirs, solids deposit in the pool behind the weir plate and change the approach conditions, so the pool is cleaned on a schedule — which is precisely why flumes are preferred in wastewater.

Capacity assessment

WPI lists performing adjustments on flow monitoring, force mains, gravity sewers, lift stations, manholes and cleanouts, and measuring and control systems. Behind those adjustments is a capacity question: is the pipe big enough for the flow it now receives?

Gravity capacity comes from Manning's equation :

Q = (1.486 / n) x A x R^(2/3) x S^(1/2)

where n is the roughness coefficient (about 0.013 for most sewer materials), A is flow area, R is hydraulic radius (area divided by wetted perimeter), and S is the slope in feet per foot. Two consequences an operator should carry:

Capacity depends on the square root of slope. Doubling slope increases capacity only about 41 percent.

A circular pipe carries its maximum flow at about 93 percent of full depth , not at exactly full, because the wetted perimeter grows faster than the area in the top of the pipe.

Design allowance for peak flow is what determines whether a system surcharges. A pipe sized for peak dry-weather flow will surcharge every time it rains if I&I is significant, which is why flow monitoring and capacity assessment are done together.

Interpreting flow data

Diurnal pattern. Normal dry-weather flow shows the familiar morning and evening peaks. A flat, featureless hydrograph in a residential basin means the meter is reading something other than sewage — often groundwater infiltration dominating the signal.

Rainfall response. Overlay flow on rainfall. A sharp, fast peak that recedes quickly is inflow — direct connections. A broad, delayed rise that persists for days is infiltration — groundwater entering through defects.

Base flow shift. A seasonal rise in the dry-weather minimum tracks the groundwater table and quantifies infiltration.

Surcharge. Depth exceeding the pipe crown means the reach is full and backing up; sustained surcharge is the direct precursor to an overflow or a basement backup.

Meter siting and maintenance

Site the meter in a straight reach , away from drops, junctions, and bends that create turbulence and non-uniform velocity profiles.

Avoid locations that silt in ; sediment over the sensor destroys both depth and velocity readings.

Confirm the pipe dimension and shape entered into the meter. An incorrect diameter propagates directly into every flow value.

Field verify with an independent method — a bucket-and-stopwatch at a drop, a dye-dilution measurement, or a manual depth reading compared with the logged value.

Clean the sensor on every visit; grease films change ultrasonic response.

Calibrate atmosphere testers used during meter site entries, which WPI lists as its own task, and treat every manhole as a permit-required confined space.

Loading diagram... Collection Flow Monitoring and Data Interpretation