Study guide

8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects

Key Takeaways Explain This Topic AI

Chemical grouting seals leaking joints but adds no structural strength, so it is the wrong choice when the pipe walls themselves are failing.

Cured-in-place pipe blinds every lateral connection, so each must be reinstated with a robotic cutter and verified by CCTV before the line returns to service.

Pipe bursting replaces at the same or larger diameter while sliplining always loses diameter and requires excavating laterals.

The frame-to-chimney joint is the most common manhole leakage point, and cone and barrel deterioration is usually sulfuric acid attack from hydrogen sulfide.

Inflow sources such as picked covers, cross connections, and roof and foundation drains give the largest immediate flow reduction for the lowest cost, while infiltration requires lining or replacement over long lengths.

Last updated: August 2026

Fixing pipe without digging it up

WPI lists rehabilitating and repairing the collection system — lift stations, manholes (collar, risers, cone, barrel, invert), sewer lines (pipe bursting, pipe lining, pipe repair), taps (top hat, grouting, protruding laterals) , and eliminating infiltration, inflow, and exfiltration — as an explicit job task, and separately lists repairing and replacing lines including force mains, combined sewers, sanitary sewers, and storm drains.

Choosing a method

The CCTV inspection and the PACP condition codes determine the method. The question is always the same: is the host pipe structurally sound enough to line , or must it be replaced ?

Method Description Best for Limits

Cured-in-place pipe (CIPP) Resin-saturated felt or fiberglass liner inverted or winched in, then cured with hot water, steam, or UV light Structurally deteriorated but round pipe; the workhorse Reduces diameter slightly; laterals must be reinstated by robotic cutter; styrene and heat handling

Sliplining A smaller-diameter new pipe pushed or pulled inside the old, annulus grouted Simple, low cost, long runs Significant diameter loss ; laterals must be excavated

Pipe bursting A bursting head fractures the old pipe outward while pulling in new HDPE Replacement with same or larger diameter Needs insertion and receiving pits; risks to nearby utilities from ground displacement

Fold-and-form / deformed liner Thermoplastic liner folded, inserted, then reverted to round with heat and pressure Round pipe, moderate deterioration Similar constraints to CIPP

Spiral wound Interlocking strip wound in place Large diameter, live flow Diameter loss

Spot repair / sectional liner Short liner or point repair at a single defect Isolated defects Not a system solution

Chemical grouting Gel injected at a joint or crack through a packer Leak sealing only , not structural Does not restore structure; may be temporary

Open cut replacement Excavate and replace Collapsed pipe, grade problems, upsizing Cost, traffic, restoration

The distinction that appears most often on exams: chemical grouting stops leakage but adds no structural strength , while CIPP and pipe bursting restore or replace structure . Grouting a joint in a pipe whose walls are failing solves the wrong problem.

Manhole rehabilitation

Manholes are a large and often underestimated source of inflow and of hydrogen sulfide damage. Components in the WPI list — collar, risers, cone, barrel, invert — each fail differently:

Frame and cover. A picked or vented cover in a low spot admits enormous stormwater inflow. Solid, gasketed covers and internal inflow dishes are cheap, high-return fixes.

Frame-to-chimney (collar) joint. The most common leakage point, since traffic loading works the frame against the cone. Repaired with chimney seals of rubber or with cementitious or urethane products.

Adjusting rings (risers). Deteriorated brick or damaged rings admit water and destabilize the frame.

Cone and barrel. Concrete attacked by sulfuric acid from hydrogen sulfide, especially above the water line. Repaired by cementitious lining, epoxy or polyurethane coating, or a full liner.

Invert and bench. Eroded or reshaped inverts cause turbulence, solids deposition, and odor. Rebuilt with grout to restore a smooth channel.

Lateral and tap defects

Taps are listed specifically. Common defects and their fixes:

Protruding (hammer) tap — a lateral driven too far into the main, catching debris and forming a chronic blockage point. Cut back with a robotic cutter.

Broken or offset connection — repaired with a top hat or T-liner , a CIPP element that seals the main-to-lateral junction from inside.

Root intrusion at the connection — cut, then sealed by grouting or a lateral liner, because cutting alone guarantees regrowth.

After CIPP lining a main , every lateral is blind until it is reinstated by a robotic cutter working from inside the lined pipe. Missing a reinstatement backs up a customer, so reinstatement is verified by CCTV before the line goes back in service.

Eliminating infiltration, inflow, and exfiltration

Rehabilitation only pays if it targets the right defects. Infiltration enters through defective joints, cracks, and lateral connections below the groundwater table; inflow enters directly through manhole covers, cross connections with storm drains, roof and foundation drains, and area drains. Exfiltration is sewage leaking out, which is a groundwater contamination issue rather than a treatment cost.

The practical rule: inflow sources are usually cheaper to fix and yield larger immediate reductions — sealing manhole covers, disconnecting downspouts, correcting cross connections — while infiltration requires lining, grouting, or replacement over long lengths. A sewer system evaluation survey that pairs flow monitoring with smoke testing, dye testing, and CCTV is what ranks the work.

Private property is where much of the flow comes from. Defective laterals, foundation drains, and sump pumps discharging to the sanitary sewer often account for more of the wet-weather response than the public main does, and a rehabilitation program that ignores private-side sources routinely underdelivers.

Loading diagram... Selecting a Rehabilitation Method from the Condition Assessment