Study guide

8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains

Key Takeaways Explain This Topic AI

Wastewater lift stations provide mechanical energy to convey sewage across topographic divides, requiring a minimum duplex configuration with N+1 redundancy where one pump can discharge 100% of peak hourly flow.

Wet well effective volume must be sized to maintain pump cycle times between 6 and 10 minutes (6 to 10 starts per hour), preventing motor stator overheating while avoiding wastewater stagnation and septicity.

Non-clog wastewater pumps utilize single-vane, vortex (recessed), or chopper/grinder impellers capable of passing minimum 3.0-inch spherical solids and macerating stringy debris.

Level control systems combine primary continuous sensors (ultrasonic, hydrostatic pressure transducers) with redundant mechanical float switches for high alarm, lag start, lead start, and stop levels.

Force mains must maintain flow velocities between 3.0 ft/s (solids scouring) and 8.0 ft/s (surge/erosion prevention) and feature dedicated wastewater air release/vacuum valves at all topographic summits.

Last updated: August 2026

Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains

Wastewater lift stations (pumping stations) and pressurized force mains are vital components of modern municipal infrastructure, overcoming topographic ridges, deep low-lying collection basins, and flat coastal or valley gradients. Lift stations collect incoming gravity flow and pump it under positive pressure through a force main to a downstream gravity interceptor or directly to a wastewater treatment facility.

1. Lift Station Configurations & Redundancy Standards

Municipal lift stations are classified into several primary structural and mechanical arrangements: +-------------------------------------------------------------------------+

  • | LIFT STATION CONFIGURATION TYPES |
  • +-------------------------------------------------------------------------+
  • | 1. Submersible Wet Well Stations: |
  • | - Most common modern design (for flows from 50 gpm to > 10,000 gpm). |
  • | - Submersible non-clog pumps and explosion-proof motors (Class I, |
  • | Division 1, Groups C & D) are submerged directly in wastewater. |
  • | - Dual stainless steel guide rail systems and auto-coupling discharge|
  • | base elbows allow pump extraction without personnel entering well. |
  • | |
  • | 2. Wet Well / Dry Pit (Dry Well) Stations: |
  • | - Wastewater collects in an isolated wet well; non-submersible pumps |
  • | reside in an adjacent dry underground chamber below liquid level. |
  • | - Flooded suction eliminates priming issues and allows clean, dry |
  • | maintenance; higher capital construction cost and flooding risk. |
  • | |
  • | 3. Suction-Lift (Self-Priming Above-Ground) Stations: |
  • | - Pumps and drive motors sit in an above-ground enclosure directly |
  • | above the wet well. Accessible maintenance without confined space |
  • | entry; limited to dynamic suction lifts < 15 to 20 feet. |
  • +-------------------------------------------------------------------------+
  • Reliability & Redundancy Standards ( N + 1 N+1 N + 1 Requirement)

Duplex Pumping Standard: Municipal lift stations must be equipped with a minimum of two (2) independent pumping units (duplex configuration) .

N + 1 N+1 N + 1 Capacity Rule: With the largest single pump out of service for repair or overhaul, the remaining pump(s) must be capable of discharging 100% of the maximum design peak hourly wastewater flow ( Q p e a k Q_{peak} Q p e ak ​ ) .

Auxiliary Standby Power: An on-site diesel emergency standby generator with an automatic transfer switch (ATS) or a dual-feed electrical utility grid connection is mandatory to prevent sanitary sewer overflows during municipal power blackouts.

Loading diagram... Submersible Lift Station Profile: Level Setpoints, Guide Rails & Force Main Valves

2. Wet Well Design, Sizing & Cycle Times

Wet wells must be sized carefully to balance two competing operational hazards:

Excessive Motor Cycling: Short cycle times cause electric motor windings to overheat from high inrush starting current, degrading insulation and tripping thermal overloads.

Excessive Wastewater Stagnation: Oversized wet wells create high hydraulic detention times, allowing solids to settle and wastewater to turn septic, generating deadly hydrogen sulfide ( H 2 S \text{H}_2\text{S} H 2 ​ S ) gas and severe odors.

Wet Well Sizing Equation

The required effective wet well volume (the liquid storage volume between the Lead Pump Start level and the Pump Stop level) is calculated using the standard minimum cycle time formula: T = 4 × V Q T = \frac{4 \times V}{Q} T = Q 4 × V ​ V = T × Q 4 V = \frac{T \times Q}{4} V = 4 T × Q ​

Where:

V V V = Effective wet well volume between Lead Start and Stop elevations (gallons)

Q Q Q = Rated discharge pumping capacity of a single pump operating alone (gallons per minute, gpm \text{gpm} gpm )

T T T = Minimum total pump cycle time from start-to-start (minutes)

Maximum motor starts per hour ( S S S ): Typically 6 to 10 starts per hour ( T = 60 / S T = 60 / S T = 60/ S , so T = 6 to 10 minutes T = 6\text{ to }10\text{ minutes} T = 6 to 10 minutes for standard induction motors up to 50 HP).

Note

Critical Hydraulic Principle: The maximum cycling frequency (shortest cycle time) occurs mathematically when the incoming gravity inflow rate ( Q i n Q_{in} Q in ​ ) is exactly 50% of the pump's discharge capacity ( Q i n = 0.5 × Q Q_{in} = 0.5 \times Q Q in ​ = 0.5 × Q ).

Self-Cleaning Wet Well Geometry

To prevent the buildup of stagnant organic sludge and grease rafts, modern wet wells incorporate steeply sloped bottom fillets (hopper bottoms) with floor slopes of 45 ∘ 45^\circ 4 5 ∘ to 60 ∘ 60^\circ 6 0 ∘ directing all settled grit directly into the pump suction bells.

3. Non-Clog Centrifugal Wastewater Pumps

Wastewater contains stringy rags, disposable wipes, plastic debris, grease, and fibrous solids that rapidly choke conventional clear-water pumps. Lift stations rely on specialized solids-handling impeller designs: +-------------------------------------------------------------------------+

  • | SOLIDS-HANDLING IMPELLER COMPARISON |
  • +-------------------------------------------------------------------------+
  • | 1. Enclosed / Semi-Open Non-Clog (Single or Two-Vane Impellers): |
  • | - Large internal waterways capable of passing a 3.0-inch (76 mm) |
  • | solid spherical sphere without lodging. |
  • | - High hydraulic efficiency (70%–85%); moderate rag-handling ability.|
  • | |
  • | 2. Vortex (Recessed) Impellers: |
  • | - Impeller is recessed completely outside the volute flow path. |
  • | - Creates a swirling liquid vortex that pulls rags, solids, and |
  • | slurry through the pump body without contacting impeller vanes. |
  • | - Lower hydraulic efficiency (45%–55%); virtually un-cloggable. |
  • | |
  • | 3. Chopper / Cutter / Grinder Pumps: |
  • | - High-hardness tool-steel cutting blades macerate rags, textiles, |
  • | and flushable wipes into a fine slurry prior to the impeller eye. |
  • | - Essential for low-pressure small-diameter sewer systems (1.5–2 in).|
  • +-------------------------------------------------------------------------+
  • 4. Level Control Technologies & Switching Logic

Reliable level sensing governs automated pump sequencing and emergency alarm annunciation:

Level Sensor Technology Operating Mechanism Maintenance Considerations

Ultrasonic Transducers Non-contact acoustic pulse reflection from liquid surface. Immune to fouling; requires false-echo filtering for foam, grease rafts, and ladder rungs.

Submersible Hydrostatic Transducers Piezoresistive diaphragm suspended near floor measures liquid head pressure ( 1 psi = 2.31 ft 1\text{ psi} = 2.31\text{ ft} 1 psi = 2.31 ft ). Highly accurate; must be installed inside a stilling well to prevent cable entanglement with rags.

Bubbler Tube Systems Constant metered compressed air purged through tube; backpressure equals liquid head. No electrical components in wet well; purge tube can clog with grease if air volume drops.

Mechanical Float Switches Tilting mercury-free mechanical microswitches inside chemical-resistant floats. Primary fail-safe backup for SCADA; requires regular pressure-washing to remove thick grease buildup.

Operational Switching Hierarchy

Level 4 (Top Elevation) — High Water Alarm: Activates visual flashing beacon, audible siren, and sends high-priority telemetry (SCADA / cellular dialer) alarms to on-call operators.

Level 3 — Lag Pump Start: Starts the second (standby) pump to operate simultaneously with the lead pump if incoming flows exceed single-pump capacity.

Level 2 — Lead Pump Start: Starts the designated duty pump. An automatic alternator circuit rotates duty cycles between Pump 1 and Pump 2 each cycle to equalize runtime and bearing wear.

Level 1 (Bottom Elevation) — Pumps Stop: Shuts down all running pumps. Must maintain sufficient liquid depth over the pump volute (minimum submergence) to prevent vortex cavitation and air-locking.

5. Force Main Design, Velocities & Surge Control

A force main is a pressurized discharge pipeline carrying wastewater under pressure from a pump station to a discharge point. +-------------------------------------------------------------------------+

  • | FORCE MAIN VELOCITY CRITERIA |
  • +-------------------------------------------------------------------------+
  • | Minimum Operating Velocity: 3.0 ft/s (0.9 m/s) |
  • | Scours settled grit and resuspends solids|
  • | |
  • | Optimum Design Range: 4.0 to 6.0 ft/s (1.2 to 1.8 m/s) |
  • | Balances energy cost against pipe wear |
  • | |
  • | Maximum Allowable Velocity: 8.0 ft/s (2.4 m/s) |
  • | Prevents extreme friction losses, wear, |
  • | and severe water hammer shockwaves |
  • +-------------------------------------------------------------------------+
  • Wastewater Air Release and Vacuum Relief Valves

Sewage force mains continuously accumulate sewer gases ( H 2 S \text{H}_2\text{S} H 2 ​ S , CH 4 \text{CH}_4 CH 4 ​ , CO 2 \text{CO}_2 CO 2 ​ , N 2 \text{N}_2 N 2 ​ ) released from turbulent pumping. If not removed, gas pockets collect at topographic high points, constricting cross-sectional pipe area and causing air binding (which dramatically increases pumping head and slashes pump flow capacity).

Wastewater Air Release Valves (ARVs): Feature an elongated body with a conical lower section that isolates the float and venting orifice from stringy solids and floating grease. Installed at all summits along the force main profile.

Air/Vacuum Combination Valves: Exhaust large volumes of air during initial pipe filling and admit air rapidly during pump shutdowns or line drainage to prevent catastrophic pipe wall collapse under vacuum .

Water Hammer & Hydraulic Transient Mitigation

Sudden pump stoppage (such as during a power failure) creates destructive acoustic pressure shockwaves ( water hammer ) governed by the Joukowsky equation ( Δ P = ρ a Δ v \Delta P = \rho a \Delta v Δ P = ρ a Δ v ). Mitigation measures include:

Non-Slam Check Valves: Rubber flapper swing check valves or spring-assisted center-guided poppet valves that close before column reversal occurs.

Hydropneumatic Surge Tanks: Pressurized bladder vessels absorbing transient kinetic energy.

Variable Frequency Drives (VFDs): Programmed with gentle acceleration and deceleration ramp times (15–30 seconds) to prevent shockwave initiation.

  • 6. Worked Lift Station Calculations
  • Worked Example 7.2.1: Sizing Wet Well Effective Volume

A municipal lift station has two identical submersible pumps rated at 600 gpm each. The pump manufacturer specifies that the 25-HP pump motors must not exceed 6 starts per hour ( S = 6 S = 6 S = 6 ) to prevent thermal insulation breakdown. Calculate the minimum required cycle time ( T T T ) and the minimum effective wet well storage volume ( V V V ) between the Lead Start and Stop elevations.

Step 1: Calculate minimum cycle time ( T T T in minutes): T = 60 minutes/hour 6 starts/hour = 10.0 minutes T = \frac{60\text{ minutes/hour}}{6\text{ starts/hour}} = 10.0\text{ minutes} T = 6 starts/hour 60 minutes/hour ​ = 10.0 minutes

Step 2: Calculate minimum effective volume ( V V V in gallons): V = T × Q 4 = 10.0 min × 600 gpm 4 = 6 , 000 4 = 1 , 500 gallons V = \frac{T \times Q}{4} = \frac{10.0\text{ min} \times 600\text{ gpm}}{4} = \frac{6,000}{4} = 1,500\text{ gallons} V = 4 T × Q ​ = 4 10.0 min × 600 gpm ​ = 4 6 , 000 ​ = 1 , 500 gallons

Step 3: Convert volume to required vertical depth in a 6-foot diameter round wet well: Cross-sectional Area A = π D 2 4 = 3.14159 × ( 6.0 ft ) 2 4 = 28.27 ft 2 \text{Cross-sectional Area } A = \frac{\pi D^2}{4} = \frac{3.14159 \times (6.0\text{ ft})^2}{4} = 28.27\text{ ft}^2 Cross-sectional Area A = 4 π D 2 ​ = 4 3.14159 × ( 6.0 ft ) 2 ​ = 28.27 ft 2 Gallons per foot of depth = 28.27 ft 2 × 7.48 gal/ft 3 = 211.5 gal/ft \text{Gallons per foot of depth} = 28.27\text{ ft}^2 \times 7.48\text{ gal/ft}^3 = 211.5\text{ gal/ft} Gallons per foot of depth = 28.27 ft 2 × 7.48 gal/ft 3 = 211.5 gal/ft Required Vertical Operating Depth = 1 , 500 gal 211.5 gal/ft = 7.09 ft \text{Required Vertical Operating Depth} = \frac{1,500\text{ gal}}{211.5\text{ gal/ft}} = 7.09\text{ ft} Required Vertical Operating Depth = 211.5 gal/ft 1 , 500 gal ​ = 7.09 ft

Worked Example 7.2.2: Force Main Velocity Verification

A lift station discharges 750 gpm through an 8-inch nominal diameter (actual inside diameter D = 7.981 inches = 0.6651 ft D = 7.981\text{ inches} = 0.6651\text{ ft} D = 7.981 inches = 0.6651 ft ) C900 PVC force main. Verify whether the flow velocity satisfies regulatory minimum and maximum limits.

Step 1: Convert flow rate from gpm to cubic feet per second (cfs): Q = 750 gpm 448.8 gpm/cfs = 1.671 cfs Q = \frac{750\text{ gpm}}{448.8\text{ gpm/cfs}} = 1.671\text{ cfs} Q = 448.8 gpm/cfs 750 gpm ​ = 1.671 cfs

Step 2: Calculate pipe cross-sectional area ( A A A ): A = π D 2 4 = 3.14159 × ( 0.6651 ft ) 2 4 = 0.3474 ft 2 A = \frac{\pi D^2}{4} = \frac{3.14159 \times (0.6651\text{ ft})^2}{4} = 0.3474\text{ ft}^2 A = 4 π D 2 ​ = 4 3.14159 × ( 0.6651 ft ) 2 ​ = 0.3474 ft 2

Step 3: Calculate flow velocity ( V = Q / A V = Q / A V = Q / A ): V = 1.671 cfs 0.3474 ft 2 = 4.81 ft/s V = \frac{1.671\text{ cfs}}{0.3474\text{ ft}^2} = 4.81\text{ ft/s} V = 0.3474 ft 2 1.671 cfs ​ = 4.81 ft/s

Step 4: Operational Evaluation: The velocity of 4.81 ft/s is comfortably above the minimum scouring velocity threshold of 3.0 ft/s 3.0\text{ ft/s} 3.0 ft/s and well below the maximum limit of 8.0 ft/s 8.0\text{ ft/s} 8.0 ft/s , representing an optimal, energy-efficient hydraulic design.