Study guide
7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap)
Colorado Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: State Laws, Regulations & CCWP Certification
1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting
2 Chapter 2: Source Water & Drinking Water Treatment Processes
2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle
3 Chapter 3: Disinfection & Chemical Addition
3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices
4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance
4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management
5 Chapter 5: Wastewater Treatment Principles & Biological Processes
5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects
6 Chapter 6: Advanced Wastewater Treatment & Solids Management
6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84
7 Chapter 7: Water Distribution Systems
7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems
8 Chapter 8: Wastewater Collection Systems
8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment
9 Chapter 9: Pumps, Motors & Utility Mechanics
9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control
10 Chapter 10: Laboratory Analysis & Water Quality Monitoring
10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)
11 Chapter 11: Operator Mathematics & Applied Calculations
11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance
12 Chapter 12: Safety, Emergency Operations & Compliance
12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties
7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap)
Key Takeaways Explain This Topic AI
A cross-connection is any actual or potential link between a potable water piping system and any source containing unapproved, non-potable, or contaminated substances.
Backflow occurs via backsiphonage (negative or sub-atmospheric pressure in the supply) or backpressure (downstream pressure exceeds supply pressure).
Hazards are classified as High Hazard (health contamination from toxic chemicals or biological pathogens) or Low Hazard (aesthetic pollution from non-toxic substances).
The Reduced Pressure Zone (RPZ) assembly protects against both backpressure and backsiphonage under high and low hazard conditions by maintaining an atmospheric relief zone between two check valves.
Under CDPHE Regulation 11.39, public water systems must maintain an active Backflow Prevention and Cross-Connection Control (BPCCC) program with an annual test compliance rate of at least 90%.
Last updated: August 2026
Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap)
The municipal water distribution system is designed to convey pure, potable water under continuous pressure to consumer properties. However, physical connections between the drinking water grid and non-potable piping systems can allow hazardous liquids, chemicals, or pathogens to flow backward into the public mains during hydraulic disturbances. Preventing such occurrences through rigorous Cross-Connection Control is a primary regulatory responsibility of certified distribution operators.
1. Regulatory Authority and Fundamental Definitions
Under CDPHE Regulation 11, Section 11.39 ( Backflow Prevention and Cross-Connection Control Rule ), every public water system in Colorado must establish and enforce a comprehensive Backflow Prevention and Cross-Connection Control (BPCCC) program. +-------------------------------------------------------------------------+
- | CORE BACKFLOW DEFINITIONS |
- +-------------------------------------------------------------------------+
- | Cross-Connection: Any actual or potential physical connection or |
- | structural arrangement between a public potable water system and any |
- | source of non-potable water, industrial liquid, gas, or sewage. |
- | |
- | Backflow: The undesirable reversal of flow of water, mixtures, or |
- | foreign substances into the distribution pipes of a potable supply. |
- | |
- | Containment Protection: Installing an approved backflow prevention |
- | assembly on the customer's service lateral immediately downstream of |
- | the water meter, isolating the entire facility from the public main. |
- | |
- | Isolation Protection (Point-of-Use): Installing a backflow device at an |
- | individual fixture or piece of equipment inside the customer's building.|
- +-------------------------------------------------------------------------+
- 2. Hydraulic Mechanics of Backflow: Backsiphonage vs. Backpressure
Backflow occurs strictly as a result of hydraulic pressure differentials through one of two distinct physical mechanisms:
Backsiphonage
Backsiphonage is backflow caused by negative or sub-atmospheric pressure ( < 0 psig < 0\text{ psig} < 0 psig or < 14.7 psia < 14.7\text{ psia} < 14.7 psia ) within the potable supply main. It operates on the same physical principle as drawing liquid through a drinking straw.
Common Causes: Severe distribution main breaks, nearby high-volume firefighting operations, undersized booster pumps pulling negative suction, or line draining during scheduled repairs.
Backpressure
Backpressure occurs when the pressure in a downstream customer piping system exceeds the operating pressure in the incoming potable supply main, forcing non-potable fluids backward into the public grid.
Common Causes: High-pressure steam boilers, unvented thermal expansion, customer booster pumps, elevated auxiliary tanks, or private irrigation systems tied into secondary agricultural ditches. BACKSIPHONAGE: [ Public Main: -5 psi (Vacuum) ] <===== [ Customer Vat / Sink: 0 psi (Atmospheric) ]
(Sub-atmospheric pressure pulls liquid into main)
- BACKPRESSURE: [ Public Main: 50 psi ] <============= [ Customer Boiler / Pump: 85 psi ]
- (Higher downstream pressure pushes fluid into main)
- 3. Hazard Assessment: High Hazard (Contamination) vs. Low Hazard (Pollution)
Selecting the correct backflow prevention assembly requires evaluating the degree of public health hazard:
High Hazard (Contamination): An impairment of drinking water quality by sewage, industrial chemicals, toxic heavy metals, or pathogenic biological agents that creates an actual threat to public health through poisoning, acute illness, or death. Examples: Chemical manufacturing facilities, mortuaries, hospitals, electroplating plants, commercial car washes, agricultural chemical injection systems, wastewater treatment facilities, and dedicated auxiliary water supplies.
Low Hazard (Pollution): An aesthetic impairment of drinking water that affects taste, odor, color, or turbidity but does not create an adverse threat to human health . Examples: Food processing steam tables, non-toxic commercial beverage carbonators, aesthetic fountains, and closed-loop hydronic heating systems without chemical additives.
Loading diagram... Backflow Assembly Hierarchy, Mechanical Action & Hazard Suitability
4. Mechanical Backflow Prevention Assemblies
Backflow prevention assemblies are precision mechanical devices approved by the University of Southern California Foundation for Cross-Connection Control and Hydraulic Research (USC-FCCCHR) or the American Society of Sanitary Engineering (ASSE) .
1. Air Gap (AG)
An Air Gap is a non-mechanical, unobstructed vertical physical separation through free atmosphere between the lowest opening of a supply pipe and the flood-level rim of a receiving vessel.
Dimension Standard: The vertical air gap distance must be at least twice the effective internal diameter ( 2 × D 2 \times D 2 × D ) of the supply pipe, and in no case less than 1.0 inch (25 mm) .
Application: Unconditionally approved for High and Low Hazards , and protects against both Backpressure and Backsiphonage (the most absolute protection available).
2. Reduced Pressure Zone Assembly (RPZ / RP - AWWA C511)
Construction: Comprises two independently acting, spring-loaded check valves separated by a hydraulically balanced, intermediate differential pressure relief valve, flanked by two resilient-seated shutoff valves and four test cocks.
Operating Principle: The central relief valve is designed to open and vent to atmosphere whenever the pressure in the intermediate zone approaches within 2.0 psi of the supply pressure. If either check valve leaks or backsiphonage occurs, the relief valve discharges water to atmosphere, maintaining the zone at lower pressure than the supply.
Application: Approved for High and Low Hazards , protecting against both Backpressure and Backsiphonage .
Installation Requirements: Must be installed in a location not subject to flooding (never in an unvented subterranean pit), minimum 12 inches above floor/ground, with an air gap funnel beneath the relief discharge port.
3. Double Check Valve Assembly (DCVA - AWWA C510)
Construction: Consists of two independently acting, spring-loaded internal check valves, two resilient-seated shutoff valves, and four test cocks.
Application: Approved for LOW HAZARD (Pollution) ONLY , protecting against both Backpressure and Backsiphonage . It cannot be used on high-hazard toxic connections because any particle lodging across both check seats would allow toxic backflow without an atmospheric discharge warning.
4. Pressure Vacuum Breaker (PVB - AWWA C512)
Construction: Contains an independently operating, spring-loaded internal check valve and an independently operating, spring-loaded air inlet valve that admits atmospheric air when pressure drops.
Application: Approved for High and Low Hazards , but for BACKSIPHONAGE ONLY . Cannot protect against backpressure.
Installation Standards: Can operate under continuous supply pressure. Must be installed at least 12 inches above the highest downstream piping, sprinkler head, or outlet .
Backflow Prevention Selection Matrix
Assembly / Device Health Hazard Suitability Backpressure Protection? Backsiphonage Protection? Continuous Pressure Allowed? Field Testable?
- Air Gap (AG) High & Low Hazard Yes Yes Yes (Physical gap) N/A (Visual inspection)
- Reduced Pressure Zone (RPZ) High & Low Hazard Yes Yes Yes Yes (4 test cocks)
- Double Check Valve (DCVA) Low Hazard ONLY Yes Yes Yes Yes (4 test cocks)
- Pressure Vacuum Breaker (PVB) High & Low Hazard NO Yes Yes Yes (2 test cocks)
Atmospheric Vacuum Breaker (AVB) High & Low Hazard NO Yes NO ( < 12 hrs/day < 12\text{ hrs/day} < 12 hrs/day ) NO (No test cocks)
5. CDPHE Regulation 11.39 BPCCC Program Requirements
Colorado public water systems must enforce stringent administrative and technical controls under Regulation 11.39 :
Annual Testing Mandate: All backflow prevention assemblies must be tested upon installation, after any repair or relocation, and at least annually (once every 12 months) by an ASSE- or ABPA-certified Cross-Connection Control Tester.
Annual Compliance Tracking Ratio ( ≥ 90 % \ge 90\% ≥ 90% ): Public water systems must track all assemblies in their service area and submit an annual BPCCC compliance report to CDPHE demonstrating that at least 90% of all registered assemblies were successfully tested and operational within the calendar year .
Certified Cross-Connection Control Technician: Surveys, hazard evaluations, and testing oversight must be coordinated by personnel holding certified CCWP Cross-Connection Control credentials.
Containment Enforcement: If a commercial or industrial customer refuses to install or test a required containment assembly, the water purveyor is legally mandated under Regulation 11.39 to terminate water service to the property to protect the public distribution grid.
- 6. Step-by-Step Backflow Scenario Analysis
- Worked Example 6.4.1: BPCCC Annual Compliance Calculation
A Colorado municipality has 1,450 registered commercial and industrial cross-connection containment assemblies within its distribution boundary. During the compliance year, the utility's certified cross-connection control database records 1,348 certified annual backflow test reports received and verified. Calculate the annual testing compliance percentage and determine if the utility satisfies CDPHE Regulation 11.39 requirements.
Step 1: Calculate the compliance testing percentage: Compliance Rate (%) = ( Number of Assemblies Tested and Verified Total Number of Registered Assemblies ) × 100 % \text{Compliance Rate (\%)} = \left(\frac{\text{Number of Assemblies Tested and Verified}}{\text{Total Number of Registered Assemblies}}\right) \times 100\% Compliance Rate (%) = ( Total Number of Registered Assemblies Number of Assemblies Tested and Verified ) × 100% Compliance Rate = ( 1 , 348 1 , 450 ) × 100 % = 92.97 % \text{Compliance Rate} = \left(\frac{1,348}{1,450}\right) \times 100\% = 92.97\% Compliance Rate = ( 1 , 450 1 , 348 ) × 100% = 92.97%
Step 2: Compare against Colorado regulatory standard: Regulatory Threshold = 90.0 % \text{Regulatory Threshold} = 90.0\% Regulatory Threshold = 90.0% Assessment: 92.97 % ≥ 90.0 % \text{Assessment: } 92.97\% \ge 90.0\% Assessment: 92.97% ≥ 90.0%
Conclusion: The municipality achieved a 92.97% annual testing compliance rate , successfully meeting the CDPHE Regulation 11.39 annual BPCCC compliance standard.