Study guide

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss

Key Takeaways Explain This Topic AI

Static pressure in a distribution network is generated strictly by water elevation difference, where 1 psi = 2.31 ft of water head and 1 ft of head = 0.433 psi.

Dynamic or residual pressure represents the actual operating pressure when water is flowing, equal to static pressure minus friction head loss and turbulence losses.

The Hydraulic Grade Line (HGL) represents piezometric head (elevation plus pressure head), while the Energy Grade Line (EGL) includes velocity head (v² / 2g).

Colorado regulations and AWWA standards mandate a minimum continuous distribution pressure of 20 psi during peak hour and maximum fire flow events to prevent back-siphonage and pathogen intrusion.

Pressure zones, booster pump stations, and pilot-operated Pressure Reducing Valves (PRVs) maintain standard operating pressures between 35 and 80 psi, preventing mains from exceeding 100 psi.

Last updated: August 2026

Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss

Water distribution systems function as pressurized, closed-conduit networks designed to deliver potable water continuously, reliably, and at adequate pressure for domestic, commercial, and fire suppression needs. Understanding the fundamental hydraulic principles governing closed pipe flow is essential for certified operators managing municipal distribution networks across Colorado.

1. Hydraulic Fundamentals: Static Head vs. Dynamic Pressure

Pressure within a water distribution grid is fundamentally generated by gravitational potential energy (elevation of storage tanks or reservoirs above customer taps) or mechanical energy imparted by distribution booster pumps.

Static Pressure and Static Head

Static head represents the vertical height of a stationary column of water above a given reference datum. When no water is flowing in the pipeline, the pressure measured at any point is known as static pressure .

The relationship between vertical water height (head) and hydrostatic pressure is governed by the specific weight of water ( γ = 62.4 lb/ft 3 \gamma = 62.4\text{ lb/ft}^3 γ = 62.4 lb/ft 3 at standard temperature): Pressure (psi) = Head (ft) × 62.4 lb/ft 3 144 in 2 / ft 2 = Head (ft) 2.31 = Head (ft) × 0.433 psi/ft \text{Pressure (psi)} = \frac{\text{Head (ft)} \times 62.4\text{ lb/ft}^3}{144\text{ in}^2/\text{ft}^2} = \frac{\text{Head (ft)}}{2.31} = \text{Head (ft)} \times 0.433\text{ psi/ft} Pressure (psi) = 144 in 2 / ft 2 Head (ft) × 62.4 lb/ft 3 ​ = 2.31 Head (ft) ​ = Head (ft) × 0.433 psi/ft Head (ft) = Pressure (psi) × 2.31 ft/psi \text{Head (ft)} = \text{Pressure (psi)} \times 2.31\text{ ft/psi} Head (ft) = Pressure (psi) × 2.31 ft/psi +-------------------------------------------------------------------------+

  • | CORE HYDRAULIC CONVERSION CONSTANTS |
  • +-------------------------------------------------------------------------+
  • | 1 pound per square inch (psi) = 2.31 feet of water column (head) |
  • | 1 foot of water column (head) = 0.433 pounds per square inch (psi) |
  • | Atmospheric pressure at sea level = 14.7 psi (33.9 ft of water) |
  • | Atmospheric pressure at Denver (5,280 ft) ≈ 12.2 psi (28.2 ft water) |
  • +-------------------------------------------------------------------------+
  • Dynamic (Residual) Pressure and Head Loss

When water begins to flow through a pipe, internal fluid friction against pipe walls and internal fluid shear cause an irreversible loss of mechanical energy, termed friction head loss ( h f h_f h f ​ ). Additionally, localized turbulence across valves, bends, tees, and meters creates minor head losses ( h m h_m h m ​ ).

Dynamic pressure (or residual pressure ) is the actual pressure measured in the pipe while water is actively moving. The fundamental relationship is expressed as: Residual Pressure Head = Static Head − Total Head Loss ( h f + h m ) \text{Residual Pressure Head} = \text{Static Head} - \text{Total Head Loss } (h_f + h_m) Residual Pressure Head = Static Head − Total Head Loss ( h f ​ + h m ​ ) Dynamic Pressure (psi) = Static Pressure (psi) − Pressure Drop due to Friction (psi) \text{Dynamic Pressure (psi)} = \text{Static Pressure (psi)} - \text{Pressure Drop due to Friction (psi)} Dynamic Pressure (psi) = Static Pressure (psi) − Pressure Drop due to Friction (psi)

As customer flow demands increase (or during high-flow events such as main flushing or structural firefighting), flow velocity rises, causing friction head loss to increase exponentially and driving residual pressure downward.

2. Hydraulic Grade Line (HGL) and Energy Grade Line (EGL)

Hydraulic engineers and operators analyze distribution networks using two primary reference gradients:

Energy Grade Line (EGL): Represents the total mechanical energy head available in the flowing fluid, comprising three components: EGL = z + P γ + v 2 2 g \text{EGL} = z + \frac{P}{\gamma} + \frac{v^2}{2g} EGL = z + γ P ​ + 2 g v 2 ​

Where:

  • z z z = Elevation head above sea level datum (ft)
  • P γ \frac{P}{\gamma} γ P ​ = Pressure head (ft of water)

v 2 2 g \frac{v^2}{2g} 2 g v 2 ​ = Velocity head (ft), where v v v is flow velocity (ft/s) and g = 32.2 ft/s 2 g = 32.2\text{ ft/s}^2 g = 32.2 ft/s 2

Hydraulic Grade Line (HGL): Represents the piezometric head , which is the sum of elevation head and pressure head ( z + P / γ z + P/\gamma z + P / γ ). The HGL indicates the physical height to which water would rise inside an open vertical standpipe or piezometer connected to the pipeline. Energy Grade Line (EGL) =========================================

  • | Velocity Head (v^2 / 2g)
  • Hydraulic Grade Line (HGL) -----------------------------------------
  • |
  • | Pressure Head (P / gamma)
  • |
  • Pipe Centerline Elevation =======o==================================
  • |
  • | Elevation Head (z)
  • |
  • Datum (Mean Sea Level) ___________________________________________
  • Critical Operating Principle: Preventing Sub-Atmospheric HGL

If the physical pipe centerline rises above the Hydraulic Grade Line, the pressure head inside the pipe becomes negative (sub-atmospheric / vacuum) . Negative pressure creates a severe health risk by inducing backsiphonage of groundwater, soil microbes, or cross-connected hazardous liquids through faulty pipe gaskets, cracked service lines, or packings.

Loading diagram... Hydraulic Profile: Static Head, HGL, Friction Slope & Residual Pressure

3. Friction Head Loss: The Hazen-Williams Formulation

In municipal drinking water engineering across North America, friction head loss in closed conduits flowing full under pressure is computed using the empirical Hazen-Williams formula : h f = 10.44 × L × Q 1.852 C 1.852 × D 4.87 h_f = \frac{10.44 \times L \times Q^{1.852}}{C^{1.852} \times D^{4.87}} h f ​ = C 1.852 × D 4.87 10.44 × L × Q 1.852 ​

Where:

  • h f h_f h f ​ = Friction head loss (feet of water)
  • L L L = Pipe length (feet)
  • Q Q Q = Volumetric flow rate (gallons per minute, gpm)
  • D D D = Pipe internal diameter (inches)
  • C C C = Hazen-Williams roughness coefficient ( C C C -factor)
  • Hazen-Williams Roughness Coefficients ( C C C -Factors)

The C C C -factor reflects the relative internal smoothness of the pipe wall. A higher C C C -factor indicates a smoother internal surface, resulting in lower friction loss and higher flow capacity for a given pressure drop.

Piping Material Typical C C C -Factor Range Operational Characteristics

PVC (C900 / C905) 140 – 150 Extremely smooth, non-corroding, maintains high C C C -factor over 50+ year lifespan.

HDPE (PE 4710) 150 – 155 Monolithic fused joints, glass-smooth interior, zero tuberculation.

New Ductile Iron (Cement-Mortar Lined) 140 Standard AWWA C104 lining prevents internal iron oxidation and tuberculation.

Standard Ductile Iron (Aged 20+ yrs) 120 – 130 Minor mineral scaling or biofilm accumulation.

Unlined Cast Iron (New / Smooth) 100 – 110 Susceptible to electrochemical corrosion and soft water attack.

Old Unlined Cast Iron (Tuberculated) 60 – 80 Heavy rust tubercles severely constrict diameter and quadruple friction head loss. Comparison of Relative Flow Capacity for Same Diameter and Pressure Drop:

  • PVC / HDPE (C = 150): [========================================] 100% Flow
  • Cement Lined Ductile (C=140): [====================================] 92% Flow
  • Aged Ductile (C = 120): [=============================] 76% Flow
  • Unlined Cast Iron (C = 100): [====================] 60% Flow
  • Tuberculated Iron (C = 70): [===========] 38% Flow
  • 4. Distribution Pressure Standards & Requirements

Operating pressures within public water systems must be maintained within strictly regulated boundaries established by the Colorado Department of Public Health and Environment (CDPHE) and AWWA standards:

Operating Condition Regulated Pressure Standard Technical & Operational Rationale

Absolute Minimum (Peak / Fire Demand) 20 psi (138 kPa) Mandatory minimum under CDPHE Regulation 11. Depressurization below 20 psi induces backsiphonage, structural pipe collapse, and requires public boil water advisories.

Normal Daily Minimum 35 – 40 psi Required to supply adequate multi-story residential fixtures, continuous lawn irrigation, and commercial appliances.

Ideal Target Operating Range 50 – 75 psi Optimum pressure balancing consumer utility against pipe stress, joint leakage, and background water loss.

Maximum Allowable Grid Pressure 80 – 100 psi Pressures exceeding 80–100 psi cause premature main breaks, household water heater pressure-relief valve discharge, and plumbing fixture failure. Individual PRVs are mandated when street mains exceed 80 psi.

5. Pressure Zones, Booster Stations & Pressure Reducing Valves (PRVs)

Colorado's mountainous and high-plains topography creates extreme elevation gradients across short geographical distances. Because every 100 feet of vertical elevation drop adds 43.3 psi of static pressure , utilities divide linear distribution networks into discrete Pressure Zones .

Pressure Zone Design Principles

Zone Boundary Isolation: Closed isolation gate valves or check valves separate adjacent pressure tiers.

Pressure Reducing Valve (PRV) Stations: Automatic, pilot-operated hydraulic control valves convey water from a higher pressure zone to a lower pressure zone while maintaining a constant, adjustable downstream delivery pressure regardless of fluctuating upstream pressures or flow rates.

Booster Pump Stations: Pumping facilities equipped with centrifugal or vertical turbine pumps convey water uphill from a lower pressure tier to an upper zone storage reservoir. Suction lines must maintain at least 20 psi positive suction pressure at all times to prevent cavitation and main depressurization. +-------------------------------------------------------------------------+

  • | PRESSURE REDUCING VALVE (PRV) MECHANICS |
  • +-------------------------------------------------------------------------+
  • | 1. Main Valve Body: Globe or angle pattern with a flexible elastomeric |
  • | diaphragm separating the upper control chamber from line flow. |
  • | 2. Adjustable Pressure-Reducing Pilot: Senses downstream delivery |
  • | pressure against an adjustable internal spring setting. |
  • | 3. High Downstream Pressure: Pilot closes, directing upstream water |
  • | into the upper diaphragm chamber, throttling the main valve closed. |
  • | 4. Dropping Downstream Pressure: Pilot opens, exhausting water from the |
  • | diaphragm chamber to downstream, allowing the main valve to open. |
  • | 5. Cavitation Management: Pressure drops exceeding 3:1 (e.g. 120 -> 40) |
  • | cause vapor bubbles to implode, requiring dual-stage PRVs or orifice |
  • | plates to prevent catastrophic metal pitting. |
  • +-------------------------------------------------------------------------+
  • 6. Step-by-Step Worked Hydraulic Calculations
  • Worked Example 6.1.1: Static Head to Pressure Conversion

An elevated storage tank in a Colorado foothills community has a high-water level at elevation 6,450.0 ft . A residential subdivision connection is located in the valley below at elevation 6,265.2 ft . Assuming the water in the tank is static (no flow in the transmission main), calculate the static pressure at the customer service connection.

Step 1: Calculate the total static head ( H H H ): H = Tank Elevation − Service Elevation = 6 , 450.0 ft − 6 , 265.2 ft = 184.8 ft of water H = \text{Tank Elevation} - \text{Service Elevation} = 6,450.0\text{ ft} - 6,265.2\text{ ft} = 184.8\text{ ft of water} H = Tank Elevation − Service Elevation = 6 , 450.0 ft − 6 , 265.2 ft = 184.8 ft of water

Step 2: Convert static head to hydrostatic pressure (psi): Static Pressure = H 2.31 ft/psi = 184.8 ft 2.31 ft/psi = 80.0 psi \text{Static Pressure} = \frac{H}{2.31\text{ ft/psi}} = \frac{184.8\text{ ft}}{2.31\text{ ft/psi}} = 80.0\text{ psi} Static Pressure = 2.31 ft/psi H ​ = 2.31 ft/psi 184.8 ft ​ = 80.0 psi Alternative method: Static Pressure = 184.8 ft × 0.433 psi/ft = 80.018 psi \text{Alternative method: } \text{Static Pressure} = 184.8\text{ ft} \times 0.433\text{ psi/ft} = 80.018\text{ psi} Alternative method: Static Pressure = 184.8 ft × 0.433 psi/ft = 80.018 psi

Worked Example 6.1.2: Residual Pressure Under Peak Fire Flow

A 1,500-foot-long, 8-inch cement-lined ductile iron water main ( C = 140 C = 140 C = 140 ) supplies an industrial park from an elevated tank providing 75.0 psi static pressure. A fire hydrant at the end of the line flows 1,200 gpm during a flow test. If the calculated friction head loss through the line at 1,200 gpm is 27.7 feet , what is the residual pressure measured at the flowing hydrant?

Step 1: Convert friction head loss from feet to psi: Friction Loss (psi) = 27.7 ft 2.31 ft/psi = 11.99 psi ≈ 12.0 psi \text{Friction Loss (psi)} = \frac{27.7\text{ ft}}{2.31\text{ ft/psi}} = 11.99\text{ psi} \approx 12.0\text{ psi} Friction Loss (psi) = 2.31 ft/psi 27.7 ft ​ = 11.99 psi ≈ 12.0 psi

Step 2: Subtract friction loss from static pressure to find residual pressure: Residual Pressure = Static Pressure − Friction Loss = 75.0 psi − 12.0 psi = 63.0 psi \text{Residual Pressure} = \text{Static Pressure} - \text{Friction Loss} = 75.0\text{ psi} - 12.0\text{ psi} = 63.0\text{ psi} Residual Pressure = Static Pressure − Friction Loss = 75.0 psi − 12.0 psi = 63.0 psi

Step 3: Regulatory Compliance Check: Because 63.0 psi is well above the Colorado regulatory minimum threshold of 20 psi , the water main easily satisfies hydraulic capacity requirements for the fire demand.