Study guide
7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing
Colorado Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: State Laws, Regulations & CCWP Certification
1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting
2 Chapter 2: Source Water & Drinking Water Treatment Processes
2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle
3 Chapter 3: Disinfection & Chemical Addition
3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices
4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance
4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management
5 Chapter 5: Wastewater Treatment Principles & Biological Processes
5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects
6 Chapter 6: Advanced Wastewater Treatment & Solids Management
6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84
7 Chapter 7: Water Distribution Systems
7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems
8 Chapter 8: Wastewater Collection Systems
8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment
9 Chapter 9: Pumps, Motors & Utility Mechanics
9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control
10 Chapter 10: Laboratory Analysis & Water Quality Monitoring
10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)
11 Chapter 11: Operator Mathematics & Applied Calculations
11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance
12 Chapter 12: Safety, Emergency Operations & Compliance
12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties
7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing
Key Takeaways Explain This Topic AI
Colorado uses dry barrel hydrants whose main valve sits below the frost line and whose drain holes open only when the hydrant is fully closed.
A dry barrel hydrant must be operated fully open or fully closed, because partial opening pressurizes the barrel while the drain holes are cracked and erodes the drainage pocket.
A barrel that does not drain will freeze and be unavailable at a fire, so it must be pumped out after every use and corrected.
Fire flow from a hydrant outlet is Q equals 29.83 times C times diameter squared times the square root of pitot pressure, with C of 0.90, 0.80, or 0.70 by outlet type.
Unidirectional flushing closes valves to force a single flow path, reaching 5 feet per second or more to scour the pipe wall while using less water than conventional flushing.
Last updated: August 2026
The most visible asset the utility owns
WPI lists "mains and related equipment (hydrants and valves, pressure regulating valves, air relief valves)" as distribution components and "maintain and repair distribution components (mains, services, meters, valves, hydrants, pumps, storage)" as a job task. Hydrants deserve their own treatment because they are simultaneously a fire protection asset, a flushing tool, a flow-testing instrument, and, in Colorado, a freeze risk.
Dry barrel versus wet barrel
- Dry barrel Wet barrel
- Main valve location At the base, below the frost line At each outlet, above ground
- Barrel contents when closed Empty (drains automatically) Full of water under pressure
- Freeze risk Low — this is why it exists High
- Where used All freezing climates, including all of Colorado Frost-free climates only
- Failure mode Drain plugged, barrel stays full and freezes Barrel freezes and splits
Every hydrant in Colorado is a dry barrel design. The main valve sits at the hydrant base below the frost line, operated by a stem running the length of the barrel. When the hydrant is closed, small drain (weep) holes at the base open automatically and let the barrel drain into the surrounding gravel drainage pocket. When it is open, those same drain holes are sealed by the valve.
Two operating consequences follow directly:
Open a hydrant fully. Partially opening a dry barrel hydrant leaves the drain holes partly open while the barrel is pressurized, eroding the drain area and washing out the surrounding soil, and it also risks contaminating the barrel. Turn the operating nut fully open, then back off a fraction of a turn to relieve stem tension.
Verify the barrel drains. After closing, listen or check with a plumber's rod or a vacuum check. A hydrant that does not drain will freeze and be unavailable at the fire. Barrels fail to drain when the drainage pocket is silted, the water table is high, or the drain holes are plugged. Where the barrel cannot drain, it must be pumped out after every use and flagged for winter attention.
Other Colorado-specific hydrant items: breakaway flanges at grade so a vehicle strike shears the hydrant cleanly without pulling the buried piping; a gate valve on the hydrant lateral so the hydrant can be isolated without shutting the main; hydrant markers for snow visibility ; and antifreeze is never put in a hydrant barrel, because the barrel is directly connected to the potable main when the hydrant is opened.
Hydrant maintenance
An annual or semi-annual program, documented per hydrant asset ID:
Inspect for damage, leaning, obstruction, and clearance.
Remove caps, inspect threads and gaskets, lubricate cap threads.
Open fully, flow briefly to flush the barrel and confirm the main valve seals, and check for a full-open stream.
Close slowly to avoid water hammer; confirm the barrel drains.
Check operating nut and stem lubrication.
Verify the isolation valve on the lateral operates.
Paint per the color code the fire authority uses for available flow.
Record findings and generate corrective work orders.
Closing slowly is not optional. A hydrant flowing 1,000 gpm slammed shut creates a pressure surge that can break mains and services elsewhere on the system.
Fire flow testing
Fire flow testing determines how much water is actually available at a location and at what residual pressure. It uses two hydrants:
The residual hydrant is closest to the point of interest; a pressure gauge is installed on it and it is not flowed .
The flow hydrant is downstream; it is opened and the discharge measured with a pitot gauge or a flow diffuser.
Procedure:
Record static pressure at the residual hydrant with nothing flowing.
Open the flow hydrant and let the flow stabilize.
Record the residual pressure at the residual hydrant and the pitot pressure at the flow hydrant outlet.
Compute the flow: Q = 29.83 x C x d² x √P , where d is the outlet diameter in inches, P is pitot pressure in psi, and C is the outlet coefficient — 0.90 for a rounded outlet, 0.80 for a square-edged outlet inside the barrel, and 0.70 for a projecting outlet.
Compute the flow available at a target residual, conventionally 20 psi , using the hydrant flow test equation.
Worked example. Static pressure is 74 psi. With one 2.5-inch square-edged outlet flowing, pitot pressure is 16 psi and residual pressure is 58 psi.
Q = 29.83 x 0.80 x (2.5)² x √16 = 29.83 x 0.80 x 6.25 x 4 = 597 gpm
Pressure drop is 74 − 58 = 16 psi.
Because available flow rises roughly with the 0.54 power of the pressure drop, dropping to a 20 psi residual (a 54 psi drop) yields substantially more than 597 gpm — the calculation gives roughly 597 x (54/16)^0.54, or about 1,170 gpm at 20 psi residual . That number is what the fire authority needs.
Distribution system flushing
WPI lists "conduct distribution system flushing" as a job task. Flushing removes accumulated sediment, biofilm, corrosion products, and stale water, and restores disinfectant residual. There are two fundamentally different approaches, and the difference is worth knowing precisely.
Conventional flushing opens hydrants and blows water out until it runs clear. It is simple and it works, but water arrives at the flushed hydrant from every direction, velocities are modest, and sediment can be drawn from clean areas into dirty ones.
Unidirectional flushing (UDF) is a systematically planned program in which valves are closed to create a single defined flow path to each flushed hydrant. Because flow is forced through one route, velocity is much higher — the design target is at least 5 feet per second, and preferably 6 or more — which actually scours the pipe wall rather than merely diluting. UDF proceeds outward from the source so that clean water always flushes into dirtier pipe, never the reverse. It uses substantially less water for a better result , and it verifies valve operability as a by-product because every valve in the sequence must be exercised.
Planning a UDF program requires an accurate map with valve and hydrant locations, a sequence of flush segments, calculated velocities, and estimated flush volumes. Operationally:
Notify customers in advance; discolored water complaints follow flushing.
Monitor chlorine residual and turbidity at the flushed hydrant and flush until both meet targets.
Dechlorinate the discharge where it reaches a storm drain or a stream, because chlorinated water is acutely toxic to aquatic life. Tablets, diffuser baskets, or liquid feed on the discharge are standard.
Control erosion and traffic , and manage discharge in freezing conditions so streets do not ice.
Record flush date, location, duration, volume, starting and ending residual and turbidity.
Velocity: the number to remember
The reason UDF works and conventional flushing often does not is velocity. Normal distribution velocities are 2 to 5 ft/s ; a main sized for fire flow may sit at a fraction of 1 ft/s under domestic demand, which is precisely why sediment settles there. Reaching 5 ft/s or more is what re-suspends and carries out the accumulated material.
The flow required to reach a target velocity comes from the continuity equation:
Q (gpm) = 2.448 x d² x V , where d is inside diameter in inches and V is velocity in ft/s.
Worked example. To scour an 8-inch main at 5 ft/s:
Q = 2.448 x (8)² x 5 = 2.448 x 64 x 5 = 783 gpm
That is comfortably within a single hydrant's capacity. To do the same in a 16-inch main:
Q = 2.448 x (16)² x 5 = 2.448 x 256 x 5 = 3,132 gpm
which exceeds what one hydrant will pass — which is why large transmission mains are usually cleaned mechanically by pigging or swabbing rather than by flushing.