Study guide
7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit
Colorado Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: State Laws, Regulations & CCWP Certification
1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting
2 Chapter 2: Source Water & Drinking Water Treatment Processes
2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle
3 Chapter 3: Disinfection & Chemical Addition
3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices
4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance
4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management
5 Chapter 5: Wastewater Treatment Principles & Biological Processes
5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects
6 Chapter 6: Advanced Wastewater Treatment & Solids Management
6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84
7 Chapter 7: Water Distribution Systems
7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems
8 Chapter 8: Wastewater Collection Systems
8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment
9 Chapter 9: Pumps, Motors & Utility Mechanics
9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control
10 Chapter 10: Laboratory Analysis & Water Quality Monitoring
10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)
11 Chapter 11: Operator Mathematics & Applied Calculations
11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance
12 Chapter 12: Safety, Emergency Operations & Compliance
12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties
7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit
Key Takeaways Explain This Topic AI
A GIS is only as good as the field feedback loop, so every repair, valve position correction, and material discovery must close out through the work order into the record.
Non-revenue water is not the same as water loss, because it includes legitimate unbilled uses such as flushing and firefighting.
Apparent losses are water delivered but not recorded and are corrected with meter and billing work, while real losses physically escaped and are corrected with leak detection and pipe replacement.
Apparent losses are valued at the retail rate while real losses are valued at production cost, so an equal volume of apparent loss is worth more to recover.
Real losses in gallons per service connection per day and the Infrastructure Leakage Index replaced percentage unaccounted for, which varies misleadingly with consumption.
Last updated: August 2026
You cannot operate what you cannot find
WPI lists "maintain an up-to-date map of the distribution system (GIS, repairs, replacements)", "interpret plans, maps, and system standard specifications", "perform operational analysis", "implement a water loss control program", and "understand elements of an asset management program" as distribution job tasks. They form one connected discipline: know what you have, measure what it does, and account for what is missing.
The record set
System map or GIS. Every main with size, material, and installation year; every valve with type, size, turns to close, and direction; every hydrant; every service; every fitting and blow-off.
As-built (record) drawings. What was actually installed, which is regularly different from what was designed. As-builts are produced at project closeout and are the source that updates the GIS.
Valve and hydrant cards or asset records. Location tied to measured ties from permanent features, plus maintenance history.
Standard specifications and details. The utility's requirements for materials, bedding, thrust restraint, tapping, disinfection, and testing, which contractors are held to.
Hydraulic model. A calibrated network model used to evaluate fire flow, size mains, and plan zone changes.
GIS is a living record, not a project. Its value collapses if crews do not report what they actually find. Every repair, replacement, valve found in the wrong position, service line material identified during a dig, and abandoned line discovered must feed back into it. Mature utilities give crews a field data collection method — a tablet form, a marked-up print, or a GPS unit — and treat the update as part of closing the work order.
Operational analysis
"Analyze operational data, meet performance objectives, document operating conditions" is the WPI phrasing. The standing analyses are:
Production versus consumption versus storage level , daily.
Pressure at monitoring points across each zone under peak and minimum demand.
Chlorine residual mapping across the system, which reveals stagnation and detention problems.
Complaint mapping — plotting discolored water, taste and odor, and pressure complaints on the map almost always reveals a spatial pattern pointing at a dead end, an unlined main, or a zone boundary.
Break history by pipe material, age, soil, and location , which drives replacement priority.
The AWWA water audit
Water loss control begins with a standardized accounting. The AWWA water balance separates the system input volume into components: SYSTEM INPUT VOLUME (corrected for master meter error)
- |
- +-- AUTHORIZED CONSUMPTION
- | +-- Billed authorized consumption --> REVENUE WATER
- | | +-- Billed metered
- | | +-- Billed unmetered
- | +-- Unbilled authorized consumption --> NON-REVENUE WATER
- | +-- Unbilled metered (e.g., municipal buildings)
- | +-- Unbilled unmetered (flushing, firefighting, street cleaning)
- |
- +-- WATER LOSSES --> NON-REVENUE WATER
- +-- APPARENT LOSSES (paper losses)
- | +-- Customer meter inaccuracy (under-registration)
- | +-- Systematic data handling and billing errors
- | +-- Unauthorized consumption (theft, illegal connections)
- +-- REAL LOSSES (physical losses)
- +-- Leakage on transmission and distribution mains
- +-- Leakage and overflows at storage tanks
- +-- Leakage on service connections up to the meter
Two distinctions decide most audit questions:
Non-revenue water is not the same as water loss. Non-revenue water includes legitimate unbilled uses such as flushing and firefighting. A utility can have high non-revenue water and low actual losses.
Apparent losses are water that was delivered but not correctly recorded — under-registering meters, billing errors, theft. Real losses are water that physically escaped the system. The distinction drives the fix: apparent losses are corrected with meter replacement, billing audits, and enforcement, while real losses are corrected with leak detection and pipe replacement. Apparent losses are also worth more per gallon , because they are valued at the retail rate rather than at the production cost.
Performance indicators replace the obsolete "percentage unaccounted for," which is misleading because it varies with consumption. Current practice uses:
Real losses in gallons per service connection per day , the primary operational indicator.
Infrastructure Leakage Index (ILI) , the ratio of current annual real losses to the unavoidable annual real losses for a system of that size, pressure, and connection density. An ILI of 1.0 is the technical minimum; well-run systems fall in the range of about 1 to 3.
Apparent losses per service connection per day.
Every audit input carries a data validity score , which tells the utility where to invest in better measurement before chasing the number itself. The most common first finding is that the master meter has never been verified , which makes every downstream conclusion unreliable.
Worked example. A system with 4,200 service connections has an annual real loss volume of 62 million gallons.
Real losses = 62,000,000 gal/year ÷ 365 days ÷ 4,200 connections = 40.4 gallons per connection per day
That figure can be compared year over year and against peer systems in a way that a bare percentage cannot.