Study guide

7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI

Colorado Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: State Laws, Regulations & CCWP Certification

1.1 CDPHE CCWP Program & Regulatory Framework (Regulation 100 / 5 CCR 1003-2) 1.2 Facility Classification & Operator in Responsible Charge (ORC) Requirements 1.3 Certification Levels, Education, Experience & Exam Eligibility (Class D-A, Grade 1-4, Class S/T) 1.4 License Renewal, Training Units (TUs) & Mandatory Regulatory Training 1.5 Colorado Primary Drinking Water Regulations (Regulation 11) & Compliance 1.6 Colorado Discharge Permit System (Regulations 61/62), DMRs & Biosolids Reporting

2 Chapter 2: Source Water & Drinking Water Treatment Processes

2.1 Raw Water Sources, High-Altitude Characteristics & Reservoir Quality 2.2 Coagulation Chemistry, Rapid Mixing & Chemical Dosing (Alum, Ferric, Polymers) 2.3 Flocculation & Sedimentation Basin Design, Operation & Settling Zones 2.4 Granular Media Filtration, Backwash Procedures & Turbidity Standards 2.5 Advanced Treatment: Membranes, Softening, GAC/PAC Adsorption & Aeration 2.6 Groundwater Sources, Well Hydraulics, Static and Pumping Levels & Specific Capacity 2.7 Source Water Characteristics, Contaminant Categories & Watershed Protection Plans 2.8 Pretreatment: Presedimentation, Aeration, Algae Control & Taste-and-Odor Management 2.9 Direct, In-Line, Pressure, Cartridge & Diatomaceous Earth Filtration 2.10 Lime-Soda Softening, Ion Exchange & Water Stabilization 2.11 Water Treatment Plant Residuals: Lagoons, Drying Beds, Land Application & Recycle

3 Chapter 3: Disinfection & Chemical Addition

3.1 Chlorine Chemistry: Hypochlorous Acid, Free/Combined Residual & Breakpoint Chlorination 3.2 Disinfection Kinetics, Baffle Factors, T10 & CT Compliance Calculations 3.3 Disinfection Byproducts (TTHMs, HAA5s) & Stage 1/2 DBP Rules 3.4 Alternative Disinfection: Chloramination, Ultraviolet (UV) Light & Chlorine Dioxide 3.5 Corrosion Control, Lead & Copper Rule Revisions (LCRR) & Fluoridation Practices

4 Chapter 4: Water Treatment Plant Equipment, Instrumentation & Maintenance

4.1 Raw Water Intakes, Screening Equipment & Raw Water Pumping 4.2 Chemical Feed Equipment: Feeders, Day Tanks, Carrier Water & Feed-Rate Calibration 4.3 Chlorination Equipment: Gas Systems, Vacuum Regulators, Hypochlorite Storage & Onsite Generation 4.4 Filter Underdrains, Support Gravel, Surface Wash, Air Scour & Filter-to-Waste 4.5 Plant Process Control, SCADA and PLC Systems, Alarm Management & Records of Operation 4.6 Preventive, Corrective and Predictive Maintenance, Work Orders & Asset Management

5 Chapter 5: Wastewater Treatment Principles & Biological Processes

5.1 Preliminary Treatment: Bar Screens, Shredders, Grit Chambers & Flow Equalization 5.2 Primary Clarification, Solids Separation & Scum Removal Mechanics 5.3 Activated Sludge Fundamentals: Aerobic Microbiology, DO Control & Biomass Growth 5.4 Return & Waste Activated Sludge Management (RAS/WAS Operations & Sludge Age) 5.5 Activated Sludge Troubleshooting: Bulking, Nocardia Foaming, Rising Sludge & Pin Floc 5.6 Wastewater Characteristics, Organic and Hydraulic Loading, Diurnal Flow & Septicity 5.7 Activated Sludge Arrangements: Conventional, Complete Mix, Step Feed, Contact Stabilization, Extended Aeration, Oxidation Ditch, SBR & MBR 5.8 Aeration Systems: Blowers, Diffusers, Surface Aerators, Oxygen Transfer & Altitude Effects

6 Chapter 6: Advanced Wastewater Treatment & Solids Management

6.1 Biological Nutrient Removal: Nitrification, Denitrification & Anoxic Zones 6.2 Biological & Chemical Phosphorus Removal (EBPR & Coagulant Precipitation) 6.3 Sludge Thickening, Aerobic & Anaerobic Digestion (Mesophilic/Thermophilic) 6.4 Dewatering Equipment (Centrifuges, Belt Filter Presses) & Biosolids Standards (Reg 64) 6.5 Pond & Lagoon Operations, Trickling Filters & Rotating Biological Contactors (RBCs) 6.6 Secondary Clarification: Overflow and Solids Loading Rates, RAS Rate Setting & Clarifier Diagnostics 6.7 Tertiary Filtration, Effluent Polishing & Wastewater Disinfection with Chlorine, Dechlorination and UV 6.8 Effluent Disposal, Rapid Infiltration Basins, Colorado Water Reuse Law & Regulation 84

7 Chapter 7: Water Distribution Systems

7.1 Distribution Hydraulics, Pressure Zones, Static Head & Friction Headloss 7.2 Finished Water Storage Tanks, Standpipes, Mixing & Water Age Control 7.3 Distribution Piping, Valves (Gate, Butterfly, PRV), Hydrants & Main Flushing 7.4 Cross-Connection Control, Hazard Assessment & Backflow Preventers (RPZ, DCVA, PVB, Air Gap) 7.5 Water Main Installation, Trenching, Repair, Pressure Testing & Disinfection (AWWA C651) 7.6 Network Layout, Pressure Zones, Demand Patterns, Fire Flow & the Hydraulic Grade Line 7.7 Fire Hydrants, Dry Barrel Operation, Fire Flow Testing & Unidirectional Flushing 7.8 Booster Pump Stations, Hydropneumatic Systems, Controls & Surge Protection 7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI 7.10 System Mapping, GIS, As-Builts, Operational Analysis & the AWWA Water Audit 7.11 Service Line Installation, Wet Tapping, Curb Stops & the Lead Service Line Inventory 7.12 Leak Detection, District Metered Areas, Minimum Night Flow & Pressure Management 7.13 Storage Facility Inspection, Sanitary Defects, Water Age Control, Cleaning & AWWA C652 Disinfection 7.14 Utility Locating, Colorado 811 Damage Prevention, the APWA Color Code & New Construction Inspection 7.15 Well and Wellhead Maintenance, Sanitary Condition, Rehabilitation & AWWA C654 Disinfection 7.16 Booster Chlorination, Remote Chemical Feed, Chemical Storage, Security & Supply Management 7.17 Distribution Sampling Technique, Chlorine Residual Monitoring & Nitrification Control in Chloraminated Systems

8 Chapter 8: Wastewater Collection Systems

8.1 Gravity Collection Systems: Flow Velocities, Slopes, Pipe Materials & Manholes 8.2 Wastewater Lift Stations: Wet Wells, Submersible Pumps, Level Controls & Force Mains 8.3 Inflow and Infiltration (I&I) Sources, Flow Monitoring, Smoke Testing & CCTV Inspection 8.4 Collection Maintenance: Hydraulic Jetting, Mechanical Rodding & FOG/Root Mitigation 8.5 Sanitary Sewer Overflows (SSOs): Root Causes, Containment, Reporting & Mitigation 8.6 Lift Station Electrical Devices, Level Detection, Telemetry, Gas Detection & Capacity Adjustment 8.7 Lift Station Configurations, Preventive Maintenance, Wet Well Cleaning, Troubleshooting & Emergency Bypass Pumping 8.8 Collection System Rehabilitation: CIPP, Pipe Bursting, Sliplining, Grouting, Manhole Repair & Tap Defects 8.9 Excavation, Hydro Excavation, Bedding and Haunching, Grade Control & Sewer Acceptance Testing 8.10 Collection System Flow Monitoring, Area-Velocity Metering, Weirs and Flumes & Capacity Assessment

9 Chapter 9: Pumps, Motors & Utility Mechanics

9.1 Centrifugal Pumps: Volutes, Impellers, Packing Seals & Mechanical Seals 9.2 Positive Displacement Pumps (Peristaltic, Diaphragm, Progressive Cavity) & Dosing Systems 9.3 Pump Performance Curves, System Head Curves, Cavitation & NPSH Calculations 9.4 Electric Motors (Single/Three Phase), Controls, Variable Frequency Drives (VFDs) & Power 9.5 Flow Meters (Venturi, Magnetic, Ultrasonic), Online Analyzers, PLCs & SCADA Telemetry 9.6 Air Compressors, Conveyors, Hoists and Cranes, Service Piping & Standby Power Generation 9.7 Valve Types and Duties, Air Release and Air-Vacuum Valves, Water Hammer & Surge Control

10 Chapter 10: Laboratory Analysis & Water Quality Monitoring

10.1 Regulatory Sampling Procedures, Chain of Custody, Holding Times & Preservation Techniques 10.2 Physical & Chemical Drinking Water Testing: Turbidity, pH, Alkalinity, Hardness & Chlorine (DPD) 10.3 Wastewater Laboratory Analysis: BOD5, COD, Total Suspended Solids (TSS) & Settleometry 10.4 Microbiological Testing: Total Coliform, E. coli (Colilert, Membrane Filtration) & QA/QC 10.5 Bench-Scale Jar Testing, Coagulant Optimization & Streaming Current Monitoring 10.6 Laboratory Equipment, Calibration and Verification, QA/QC Program & Certified Laboratory Requirements 10.7 Nutrient Series, Metals Sampling, Whole Effluent Toxicity & Electrode Measurements (DO, pH, ORP, H2S)

11 Chapter 11: Operator Mathematics & Applied Calculations

11.1 Core Conversions, Geometric Area, Pipe Volume & Continuous Flow Rate (MGD, GPM, cfs) 11.2 Chemical Dosage, The Standard "Pounds Formula", Active Chemical & Solution Purity 11.3 Hydraulic Retention Time (HRT), Surface Overflow Rate (SOR) & Weir Overflow Rates 11.4 Process Control Calculations: F/M Ratio, MCRT/Solids Retention Time (SRT) & Sludge Volume Index (SVI) 11.5 Distribution Pressure, Static vs Dynamic Head, Water Horsepower & Wire-to-Water Efficiency 11.6 CT Calculations: Baffling Factors, T10, Temperature and pH Corrections & Multi-Segment Compliance

12 Chapter 12: Safety, Emergency Operations & Compliance

12.1 Permit-Required Confined Space (PRCS) Entry, Atmospheric Testing (O2/LEL/H2S/CO) & Rescue 12.2 Control of Hazardous Energy: Lockout/Tagout (LOTO), Arc Flash & Electrical Safety 12.3 Chemical Safety: Chlorine Gas Handling, Ton Cylinders, Sulfur Dioxide, Ammonia & SDS/GHS 12.4 Trenching & Excavation: Soil Classification, Sloping, Shoring, Shielding & Competent Person Rules 12.5 Emergency Action Plans, Security Vulnerability, Spill Containment & CDPHE Tier 1/2/3 Public Notice 12.6 Work Zone Traffic Control, PPE, Fall Protection, Fire Extinguishers, First Aid & Bloodborne Pathogens 12.7 Standard Operating Procedures, Operating Records, Regulatory Reporting, Customer Complaints & Supervisory Duties

7.9 Customer and Master Metering, Meter Sizing, Accuracy Testing, AMR & AMI

Key Takeaways Explain This Topic AI

Positive displacement meters are accurate at low flow but limited in capacity, while turbine meters handle high flow but under-register at low flow, which is why compound meters exist.

Meters must be sized to the actual flow range rather than to pipe diameter, because an oversized meter never registers the low flows that pass through it.

Turbine and magnetic meters require developed velocity profiles, commonly 5 to 10 pipe diameters upstream and 2 to 5 downstream, and a completely full pipe.

Mechanical meters wear in one direction only: they slow down and under-register, so aging meters cause revenue loss rather than overbilling.

AMI provides hourly interval data that identifies continuous flow at a service as a customer-side leak and supports district metered areas and live water balance.

Last updated: August 2026

Measuring what leaves the system

WPI lists "metering and related equipment (remote readers, meter replacements)" as a distribution component and "conduct meter reading" and "maintain facility and process control water meters" as job tasks. Meters serve three separate purposes — customer billing, system water balance, and process control — and a meter that is adequate for one may be inadequate for another.

Meter types and where each belongs

Type Principle Best application Notes

Positive displacement (nutating disc, oscillating piston) Fills and empties a chamber of known volume Residential and small commercial services Excellent low-flow accuracy ; limited capacity; damaged by debris

  • Single-jet / multi-jet Jets strike an impeller Small services Simple; moderate accuracy
  • Turbine Axial rotor in the flow stream Large, steady, high flows Poor low-flow accuracy; low headloss

Compound PD meter for low flow plus turbine for high flow, with a crossover valve Services with a wide flow range — hotels, schools, hospitals Best of both; crossover valve is the wear point

Fire service / detector check Large line with a small bypass meter Combined fire and domestic services The bypass meter catches leakage and unauthorized use

Electromagnetic (mag) Faraday induction; no moving parts Master meters, plant process, raw water Requires conductive liquid; needs full pipe; wide rangeability

Ultrasonic (transit time) Time difference of sound pulses upstream vs downstream Master meters, portable surveys Clamp-on versions install without shutdown

Venturi, orifice, propeller Differential pressure or mechanical Plant and well discharge Venturi has low permanent headloss

The distinction most likely to be tested: positive displacement meters are accurate at low flow but limited in capacity, while turbine meters handle high flow but under-register at low flow. A compound meter exists specifically because many commercial services have both a large peak and long periods of trickle flow — a dripping fixture or a slow leak — that a turbine alone would never record.

Meters must be sized for actual flow, not for pipe size. An oversized meter is the single most common cause of apparent water loss: at flows below its low-flow accuracy threshold, it simply does not turn, and the utility delivers water it never bills.

Installation requirements

Straight pipe runs upstream and downstream, commonly 5 to 10 diameters up and 2 to 5 down for turbine and mag meters, so the velocity profile is developed. Elbows, valves, and pumps immediately upstream distort the profile and bias the reading.

Full pipe. Mag and ultrasonic meters read wrong or not at all with entrained air, so meters go in a location that stays full, and air-release valves are placed upstream where needed.

Correct orientation per the manufacturer, with the arrow in the direction of flow.

Strainers upstream of turbine and PD meters where debris is a risk.

Isolation valves and a test tee so the meter can be tested and changed without a shutdown.

Freeze protection in Colorado: meter pits below the frost line with insulated lids, or interior settings. A frozen meter register is both a lost revenue and a broken asset.

Accuracy testing and replacement

AWWA accuracy standards for new small meters are approximately 95 to 101 percent at the minimum test flow, and 98.5 to 101.5 percent at the intermediate and maximum test flows . Meters are tested against a calibrated volumetric standard or a certified test bench at low, intermediate, and high flow rates.

Meters wear in one direction: they slow down and under-register. Sediment abrades the measuring chamber, bearings wear, and over 15 to 20 years a residential meter may under-register by several percent. Replacement programs are therefore economic decisions, not just maintenance: the cost of a new meter is compared against the recovered revenue from restored accuracy.

Large meters are tested far more often than small ones — commonly annually — because a single large commercial or industrial meter can represent more revenue than thousands of residential meters, and because compound meter crossover valves fail in ways that lose large volumes silently.

Remote reading

AMR (automatic meter reading) transmits the register reading to a drive-by or walk-by receiver, eliminating manual reads.

AMI (advanced metering infrastructure) provides a fixed network with hourly or more frequent interval data delivered continuously.

AMI changes what an operator can do. Continuous consumption data identifies continuous flow at a service — the signature of a customer-side leak — and can trigger an automatic notification. It supports district metered areas and near-real-time water balance, detects backflow events at services equipped with reverse-flow detection, and turns the water audit from an annual exercise into a live tool. It is also the reason master meter accuracy matters more than ever: an accurate customer read set is only useful against an equally accurate system input volume.

Loading diagram... Meter Selection, Installation, and Accuracy Management