Study guide

VLAN, STP, Trunk, Native VLAN, and ACL Issues

CompTIA Network+ N10-009

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

Current Exam Facts and Applied Networking Judgment Official Domain Weights and an 8-12 Week Study Plan How to Use Labs, Practice, and PBQ Workflow Missed-Question Notebook and Final Readiness Metrics

2 Domain 1: Networking Concepts (23%)

OSI and TCP/IP Models with Device and Protocol Mapping Networking Appliances and Where They Operate Ports and Protocol Decision Table Traffic Types and Encapsulation Flow

3 Domain 1: Media, Connectors, Transceivers, and Network Architectures

Copper, Fiber, Coax, and DAC Media Connector and Transceiver Selection Network Topologies and Design Patterns Cloud and Virtual Networking Concepts

4 Domain 1: IP Addressing and Subnetting Mastery

IPv4 Classes, Private/Public, APIPA, and Loopback CIDR, VLSM, and Subnet Math IPv6 Address Types and Notation Routing Basics and Longest Prefix Match

5 Domain 2: Network Implementation - Routing

Static vs Dynamic Routing and Route Selection OSPF, EIGRP, and BGP Basics at Network+ Depth NAT/PAT, VIP/FHRP, and Subinterfaces Routing PBQs and Troubleshooting Route Table Clues

6 Domain 2: Network Implementation - Switching

VLANs, Access Ports, Trunks, and Native VLAN STP/RSTP Loop Prevention and Bridge Roles Port Aggregation/LACP, MTU, Jumbo Frames, and Interface Settings Switch Implementation PBQs and Common Misconfigurations

7 Domain 2: Network Implementation - Wireless and Physical Implementation

Wi-Fi Standards, Bands, and Channels SSID Security, Guest Networks, and Authentication Antennas, Coverage, Roaming, Interference, and Site Surveys Physical Installation Implications

8 Domain 2: Network Implementation - Services Implementation

DNS Record Types and Troubleshooting Cues DHCP, DHCPv6, SLAAC, Scopes, Leases, and Relay NTP, PTP, NTS, and Time-Sensitive Networking Service Implementation PBQs: DNS, DHCP, VLANs, and Firewall Direction

9 Domain 3 Part A: Network Operations Documentation and Governance

Physical, Logical, Rack, Cable, Wireless Diagrams, and IPAM Asset Inventory, Baselines, SLAs, SOPs, and Runbooks Change Management and Request Tracking Lifecycle, EOL, EOS, Decommissioning, and Configuration Management

10 Domain 3 Part B: Monitoring, Remote Access, and Resilience

SNMP, Flow, Syslog, Packet Capture, Log Aggregation, APIs, and Port Mirroring Baselines and Performance Metrics Remote Access, Management Paths, and Secure Admin Habits DR and HA Concepts: RPO, RTO, MTTR, MTBF, Sites, Failover, and Testing

11 Domain 4: Logical Security and Secure Access (14%)

Encryption in Transit, Encryption at Rest, PKI, and Certificates IAM, MFA, SSO, Directory Services, and AAA Authorization, Least Privilege, RBAC, Geofencing, and Time-Based Access VPNs and Secure Management Design

12 Domain 4: Segmentation, Risk, and Network Attacks (14%)

Segmentation for Guest, BYOD, IoT, IIoT, SCADA, ICS, and OT Risk, Compliance, Audit, Data Locality, PCI, and GDPR Network Attacks and Scenario Cues Attack-to-Mitigation PBQ Tables

13 Domain 4: Security Controls and Hardening (14%)

Firewalls, IDS, IPS, Security Zones, and Screened Subnets ACLs, Filtering, NAC, Hardening, and Key Management Deception Technologies and Physical Security Zero Trust, SASE, and Trusted or Untrusted Zone Decisions

14 Domain 5: Troubleshooting Methodology and Tools (24%)

Official Troubleshooting Methodology and Evidence Handling Command-Line Tools: ping, traceroute, nslookup, dig, ipconfig, ifconfig, ip, arp, netstat, ss, and route Packet, Protocol, and Wi-Fi Analyzers Choosing the Right Tool by Symptom PBQs

15 Domain 5: Physical, Interface, and Wireless Troubleshooting (24%)

Cable Issues: Type, Attenuation, Crosstalk, Termination, and TX/RX Interface Issues: Errors, Discards, Duplex, Speed, Port Status, and PoE Transceiver, Fiber, and Signal Strength Troubleshooting Wireless Troubleshooting: Interference, Channels, Roaming, RSSI/SNR, Security, and Captive Portals

16 Domain 5: Network Services, Switching, Routing, and Performance Troubleshooting (24%)

DHCP, DNS, NTP, and IP Addressing Issues VLAN, STP, Trunk, Native VLAN, and ACL Issues Routing, Default Gateway, Route Table, and NAT Issues Congestion, Latency, Jitter, Packet Loss, and Application Performance Clues

17 Performance-Based Question Labs

Subnetting and VLSM Design Lab VLAN, Trunk, Router-on-a-Stick, and Firewall Rule Lab Wireless Deployment and Troubleshooting Lab Monitoring, Log Triage, and Route or Service Troubleshooting Lab

18 High-Yield Reference and Final Study Plan

High-Yield Ports and Protocols Table Wi-Fi, Cabling, Connectors, and Transceivers Quick Table Acronyms and Command-Line Tool Quick Table Final 7-Day Review Plan and Readiness Checklist

19 Final Synthesis: Strategy, Remediation, and Readiness

Mixed-Set Decision Strategy for Qualifiers and Close Answers Missed-Question Remediation Notebook by Error Type Exam-Day Time Management and PBQ Order 100-Question Readiness Simulation Blueprint Mapped to N10-009 Weights

VLAN, STP, Trunk, Native VLAN, and ACL Issues

Key Takeaways Explain This Topic AI

VLAN faults are usually a wrong access VLAN, a VLAN missing from a trunk's allowed list, a native VLAN mismatch, or bad SSID-to-VLAN mapping.

802.1Q tags frames with a 12-bit VLAN ID (1-4094); the native VLAN is the single untagged VLAN on a trunk and must match both ends.

STP blocks redundant ports to break loops; BPDU guard err-disables an edge port that unexpectedly receives a BPDU.

ACLs can make a healthy route look broken because the packet is dropped after the forwarding decision.

Layer 2 troubleshooting checks both switch configuration and the actual path a frame takes hop by hop.

Last updated: June 2026

VLAN, STP, Trunks, and ACLs

Switching problems create selective failures, and that selectivity is the clue. One desk jack cannot reach printers, one VLAN never gets DHCP, a server works on one switch but not another, or a guest SSID drops users into the wrong subnet. These narrow symptoms point at VLAN assignment, trunking, Spanning Tree Protocol (STP), or filtering rather than a whole-site outage.

VLAN Assignment Problems

A Virtual LAN (VLAN) is a Layer 2 broadcast domain identified by a 12-bit ID from 1 to 4094 (VLAN 1 is the default; 0 and 4095 are reserved). An access port carries exactly one VLAN untagged toward the endpoint.

  • Symptom Likely issue
  • Device gets an address from the wrong subnet Access port in wrong VLAN or bad SSID-to-VLAN mapping
  • New VLAN works on one switch, not another VLAN not created, not active, or not trunked across the path
  • Phone works but attached PC does not Voice VLAN configured, data VLAN missing on the port
  • DHCP fails only on one VLAN VLAN path, relay, scope, or ACL on that VLAN
  • Works in one jack but not another Port VLAN, port security, cabling, or config drift

Verify the actual port the device lands on. Documentation goes stale and patch panels rarely map cleanly to the expected switch port. Confirm with show interface status and show vlan brief before changing anything. A common trap: a phone passes a tagged voice VLAN and an untagged data VLAN on one port, so if only the data VLAN is missing from the port config the phone registers fine but the daisy-chained PC gets no address. Treat "phone works, PC does not" as a port-VLAN clue, not a cabling fault.

Trunk and Native VLAN Issues

A trunk carries multiple VLANs between switches, routers, firewalls, hypervisors, or access points using IEEE 802.1Q tagging, which inserts a 4-byte tag holding the VLAN ID. The native VLAN is the one VLAN sent untagged across a trunk; both ends must agree on its number or untagged frames land in the wrong VLAN.

  • Trunk check Why it matters
  • Both sides trunking where required A static-access side drops or mis-handles tagged frames
  • Allowed VLAN list includes the needed VLAN A pruned VLAN is blocked across that link
  • Native VLAN matches on both ends Untagged traffic lands in the wrong VLAN if mismatched
  • VLAN exists and is active Some platforms will not forward an absent/inactive VLAN
  • AP/hypervisor tagging matches the switch Virtual or wireless clients map to the wrong VLAN

A native VLAN mismatch is dangerous precisely because it does not break every flow; tagged VLANs keep working while untagged management or voice traffic crosses into the wrong domain, which can also raise security alerts. Cisco logs this as a CDP/native-VLAN mismatch.

STP Issues

Spanning Tree Protocol prevents Layer 2 loops by electing a root bridge (lowest bridge ID) and blocking redundant links. Blocking is normal and protective.

  • STP clue Meaning
  • A redundant port is blocking STP is preventing a loop on that path
  • Root bridge changed unexpectedly A lower-priority switch joined; traffic paths shift
  • Port err-disabled after a BPDU on an edge BPDU guard shut it down for protection
  • Loop guard / root guard triggered Protection feature saw an unexpected topology
  • Broadcast storm, MAC table instability A loop exists where STP is missing or disabled

Never "fix" a blocked link by disabling STP. Find why the role or topology changed first; PortFast plus BPDU guard belong on edge ports facing endpoints, not on inter-switch links.

ACL Filtering

An Access Control List (ACL) lives on routers, Layer 3 switches, firewalls, and wireless controllers. Because the drop happens after the forwarding decision, a perfectly good route can look broken. ACLs are evaluated top-down with an implicit deny any at the end, so rule order matters.

  • ACL symptom Likely clue
  • Ping works but the app port fails ICMP permitted, TCP/UDP port denied
  • One subnet reaches a server, another cannot Source network missing from a permit rule
  • Return traffic fails Stateless ACL lacks the reverse-direction rule
  • New VLAN cannot reach DNS or the DHCP relay Infrastructure services not permitted
  • Logs show deny hits Policy is dropping traffic by design
  • Practical Troubleshooting Flow

Identify source port, VLAN, IP subnet, and the destination.

Verify the access VLAN or SSID-to-VLAN mapping on the real port.

Check trunk allowed VLANs and native VLAN on every hop.

Review STP role, state, and protection events ( show spanning-tree ).

Test the gateway and the routed path.

Read ACLs and hit-counters for denied traffic.

Exam Focus

For N10-009: a wrong subnet right after plugging in is usually VLAN assignment; a VLAN that works locally but not across switches is a trunk or allowed-VLAN issue; a blocked redundant link is normal STP; and a selective service failure on an otherwise routable path is frequently an ACL, not a route.