Study guide

Copper, Fiber, Coax, and DAC Media

CompTIA Network+ N10-009

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

Current Exam Facts and Applied Networking Judgment Official Domain Weights and an 8-12 Week Study Plan How to Use Labs, Practice, and PBQ Workflow Missed-Question Notebook and Final Readiness Metrics

2 Domain 1: Networking Concepts (23%)

OSI and TCP/IP Models with Device and Protocol Mapping Networking Appliances and Where They Operate Ports and Protocol Decision Table Traffic Types and Encapsulation Flow

3 Domain 1: Media, Connectors, Transceivers, and Network Architectures

Copper, Fiber, Coax, and DAC Media Connector and Transceiver Selection Network Topologies and Design Patterns Cloud and Virtual Networking Concepts

4 Domain 1: IP Addressing and Subnetting Mastery

IPv4 Classes, Private/Public, APIPA, and Loopback CIDR, VLSM, and Subnet Math IPv6 Address Types and Notation Routing Basics and Longest Prefix Match

5 Domain 2: Network Implementation - Routing

Static vs Dynamic Routing and Route Selection OSPF, EIGRP, and BGP Basics at Network+ Depth NAT/PAT, VIP/FHRP, and Subinterfaces Routing PBQs and Troubleshooting Route Table Clues

6 Domain 2: Network Implementation - Switching

VLANs, Access Ports, Trunks, and Native VLAN STP/RSTP Loop Prevention and Bridge Roles Port Aggregation/LACP, MTU, Jumbo Frames, and Interface Settings Switch Implementation PBQs and Common Misconfigurations

7 Domain 2: Network Implementation - Wireless and Physical Implementation

Wi-Fi Standards, Bands, and Channels SSID Security, Guest Networks, and Authentication Antennas, Coverage, Roaming, Interference, and Site Surveys Physical Installation Implications

8 Domain 2: Network Implementation - Services Implementation

DNS Record Types and Troubleshooting Cues DHCP, DHCPv6, SLAAC, Scopes, Leases, and Relay NTP, PTP, NTS, and Time-Sensitive Networking Service Implementation PBQs: DNS, DHCP, VLANs, and Firewall Direction

9 Domain 3 Part A: Network Operations Documentation and Governance

Physical, Logical, Rack, Cable, Wireless Diagrams, and IPAM Asset Inventory, Baselines, SLAs, SOPs, and Runbooks Change Management and Request Tracking Lifecycle, EOL, EOS, Decommissioning, and Configuration Management

10 Domain 3 Part B: Monitoring, Remote Access, and Resilience

SNMP, Flow, Syslog, Packet Capture, Log Aggregation, APIs, and Port Mirroring Baselines and Performance Metrics Remote Access, Management Paths, and Secure Admin Habits DR and HA Concepts: RPO, RTO, MTTR, MTBF, Sites, Failover, and Testing

11 Domain 4: Logical Security and Secure Access (14%)

Encryption in Transit, Encryption at Rest, PKI, and Certificates IAM, MFA, SSO, Directory Services, and AAA Authorization, Least Privilege, RBAC, Geofencing, and Time-Based Access VPNs and Secure Management Design

12 Domain 4: Segmentation, Risk, and Network Attacks (14%)

Segmentation for Guest, BYOD, IoT, IIoT, SCADA, ICS, and OT Risk, Compliance, Audit, Data Locality, PCI, and GDPR Network Attacks and Scenario Cues Attack-to-Mitigation PBQ Tables

13 Domain 4: Security Controls and Hardening (14%)

Firewalls, IDS, IPS, Security Zones, and Screened Subnets ACLs, Filtering, NAC, Hardening, and Key Management Deception Technologies and Physical Security Zero Trust, SASE, and Trusted or Untrusted Zone Decisions

14 Domain 5: Troubleshooting Methodology and Tools (24%)

Official Troubleshooting Methodology and Evidence Handling Command-Line Tools: ping, traceroute, nslookup, dig, ipconfig, ifconfig, ip, arp, netstat, ss, and route Packet, Protocol, and Wi-Fi Analyzers Choosing the Right Tool by Symptom PBQs

15 Domain 5: Physical, Interface, and Wireless Troubleshooting (24%)

Cable Issues: Type, Attenuation, Crosstalk, Termination, and TX/RX Interface Issues: Errors, Discards, Duplex, Speed, Port Status, and PoE Transceiver, Fiber, and Signal Strength Troubleshooting Wireless Troubleshooting: Interference, Channels, Roaming, RSSI/SNR, Security, and Captive Portals

16 Domain 5: Network Services, Switching, Routing, and Performance Troubleshooting (24%)

DHCP, DNS, NTP, and IP Addressing Issues VLAN, STP, Trunk, Native VLAN, and ACL Issues Routing, Default Gateway, Route Table, and NAT Issues Congestion, Latency, Jitter, Packet Loss, and Application Performance Clues

17 Performance-Based Question Labs

Subnetting and VLSM Design Lab VLAN, Trunk, Router-on-a-Stick, and Firewall Rule Lab Wireless Deployment and Troubleshooting Lab Monitoring, Log Triage, and Route or Service Troubleshooting Lab

18 High-Yield Reference and Final Study Plan

High-Yield Ports and Protocols Table Wi-Fi, Cabling, Connectors, and Transceivers Quick Table Acronyms and Command-Line Tool Quick Table Final 7-Day Review Plan and Readiness Checklist

19 Final Synthesis: Strategy, Remediation, and Readiness

Mixed-Set Decision Strategy for Qualifiers and Close Answers Missed-Question Remediation Notebook by Error Type Exam-Day Time Management and PBQ Order 100-Question Readiness Simulation Blueprint Mapped to N10-009 Weights

Copper, Fiber, Coax, and DAC Media

Key Takeaways Explain This Topic AI

Twisted-pair copper Ethernet is limited to 100 m total channel (90 m horizontal plus 10 m patch) and is the default for Power over Ethernet endpoints.

Multimode fiber (OM3/OM4/OM5, orange/aqua/lime jackets) carries 10G to ~300-550 m; single-mode (OS2, yellow jacket) reaches tens of kilometers.

Coax in Network+ means RG-6/RG-59 broadband with F-type and legacy 10BASE2/10BASE5 bus with BNC; it is a shared or provider-handoff clue.

Direct attach copper (DAC) is a fixed factory-terminated SFP/QSFP assembly for ~1-7 m intra-rack links and needs no separate optics.

Match the medium to the dominant constraint in the scenario: distance, EMI immunity, electrical isolation, PoE, or cost.

Last updated: June 2026

How Network+ Frames Media Questions

N10-009 media items describe one dominant physical constraint: distance, speed, electromagnetic interference (EMI), cost, Power over Ethernet (PoE), or an existing connector. Identify the constraint first, then pick the medium. The exam is 90 questions in 90 minutes with a passing score of 720 on a 100-900 scale , and Domain 1 (Networking Concepts) is 23% of that weight, so media recall is heavily tested.

  • Medium Best fit Hard limit / strength Watch for
  • Twisted-pair copper Workstations, APs, phones, cameras 100 m channel, supports PoE EMI, category mismatch

Multimode fiber (MMF) Building/data-center optical runs EMI-immune, ~300-550 m at 10G Modal dispersion, shorter than SMF

Single-mode fiber (SMF) Campus, ISP, long haul Tens of km, highest bandwidth Pricier optics, dirty/bent end faces

  • Coaxial cable Broadband, RF, CCTV, legacy bus Shielded RF carrier Shared medium or ISP-handoff clue
  • Direct attach copper (DAC) Intra-rack switch-to-server Cheap, low-latency, no optics Fixed 1-7 m length only

Twisted-Pair Copper

Balanced twisted pairs cancel interference. The classic clue is an endpoint inside an office that also needs power, because PoE (802.3af 15.4 W), PoE+ (802.3at 30 W), and PoE++/4PPoE (802.3bt up to ~71-100 W) all ride twisted pair. The total Ethernet channel is 100 meters (about 328 feet): 90 m of solid horizontal cable plus 10 m of stranded patch cords. Exceed it and you see late collisions, CRC errors, or no link.

  • Category Rated speed / bandwidth Exam association
  • Cat 5e 1 GbE, 100 MHz Older office access
  • Cat 6 10 GbE to 55 m, 250 MHz Mixed 1G/10G drops
  • Cat 6a 10 GbE to 100 m, 500 MHz 10G horizontal standard, low alien crosstalk
  • Cat 7 / 7a Shielded, 600-1000 MHz High-EMI niche, GG45/TERA
  • Cat 8 25/40 GbE to 30 m Data-center top-of-rack only

Cat 6 carries 10G only to ~55 m ; for a full 100 m 10G drop you need Cat 6a . Shielded twisted pair (STP/F/UTP) helps near motors or generators but must be bonded and grounded at both ends, or the shield becomes an antenna and worsens the fault. Standard office wiring is unshielded twisted pair (UTP).

Fiber Media

Fiber carries light, so it is immune to EMI and creates no copper path between buildings (no shared ground, no lightning conduction). That makes it the answer whenever the scenario mentions electrical isolation, long distance, or an electrically noisy environment.

  • Fiber grade Core / type Typical 10G reach Jacket color clue
  • OM1 62.5 um MMF ~33 m at 10G Orange
  • OM3 50 um laser-optimized MMF ~300 m at 10G Aqua
  • OM4 50 um MMF ~400 m at 10G Aqua/violet
  • OM5 wideband MMF ~400 m, SWDM Lime green
  • OS2 9 um single-mode 10-40+ km Yellow

Key numbers: 10GBASE-SR over OM3 reaches ~300 m; over OM4 ~400 m. 10GBASE-LR over OS2 single-mode reaches ~10 km, and 10GBASE-ER ~40 km. Common faults are excessive bend radius, dirty end faces, mismatched optics, and Tx/Rx polarity reversal. In a PBQ, inspect and clean end faces, confirm the transceiver matches the fiber type, verify polarity, and check light/dBm levels with a meter when available.

Coax and DAC

Coaxial cable has a center conductor, dielectric, braided shield, and jacket. Network+ coax appears as broadband RG-6/RG-59 with screw-on F-type (cable modems, DOCSIS, antenna/RF, some CCTV) and legacy bus Ethernet 10BASE2 (Thinnet) / 10BASE5 (Thicknet) with BNC . Coax is a shared-medium or provider-handoff clue.

Direct attach copper (DAC) is different: a factory-terminated twinaxial assembly with SFP+/SFP28/QSFP ends fused to the cable. It needs no separate optics, runs ~1-7 m, and is the cheapest way to do 10/25/40/100G inside one rack.

  • Requirement Media answer Why
  • Power a ceiling AP from the switch Twisted-pair copper PoE rides copper
  • Link two buildings across campus Single-mode fiber Distance + electrical isolation
  • Connect adjacent top-of-rack switches DAC Short, cheap, fast
  • Cable modem to provider wiring Coax (F-type) Broadband RF handoff
  • Run through a noisy industrial bay Fiber EMI immunity
  • 10G optical run inside one data center Multimode fiber Cost-effective short reach

Worked Scenarios and Selection Drill

Scenario 1: A warehouse camera drops link every time large motors start, on a long copper run beside power conduit. Do not just "replace the cable." The root constraints are EMI and distance. Best design: fiber for the long noisy segment, copper only for the final PoE camera drop via a media converter or PoE switch near the endpoint.

Scenario 2: A server team wants a low-cost 25 GbE link between a server and a top-of-rack switch 2 m away. DAC wins: it is within DAC's ~1-7 m range, far cheaper than two SFP28 optics plus a fiber patch, and adds minimal latency.

If the question says... Think...

  • Needs PoE Twisted-pair copper
  • Long distance between buildings Single-mode fiber
  • 25/40/100G inside the same rack DAC
  • Existing cable-TV provider handoff Coax / F-type
  • EMI or electrical isolation required Fiber
  • Short 10G optical run in a data center Multimode fiber
  • 10G drop at full 100 m on copper Cat 6a

Common trap: choosing Cat 6 for a 100 m 10G run (it only reaches ~55 m at 10G), or choosing coax for a modern LAN uplink when the real clue was a cable-broadband handoff.