Study guide
Antennas, Coverage, Roaming, Interference, and Site Surveys
CompTIA Network+ N10-009
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
Current Exam Facts and Applied Networking Judgment Official Domain Weights and an 8-12 Week Study Plan How to Use Labs, Practice, and PBQ Workflow Missed-Question Notebook and Final Readiness Metrics
2 Domain 1: Networking Concepts (23%)
OSI and TCP/IP Models with Device and Protocol Mapping Networking Appliances and Where They Operate Ports and Protocol Decision Table Traffic Types and Encapsulation Flow
3 Domain 1: Media, Connectors, Transceivers, and Network Architectures
Copper, Fiber, Coax, and DAC Media Connector and Transceiver Selection Network Topologies and Design Patterns Cloud and Virtual Networking Concepts
4 Domain 1: IP Addressing and Subnetting Mastery
IPv4 Classes, Private/Public, APIPA, and Loopback CIDR, VLSM, and Subnet Math IPv6 Address Types and Notation Routing Basics and Longest Prefix Match
5 Domain 2: Network Implementation - Routing
Static vs Dynamic Routing and Route Selection OSPF, EIGRP, and BGP Basics at Network+ Depth NAT/PAT, VIP/FHRP, and Subinterfaces Routing PBQs and Troubleshooting Route Table Clues
6 Domain 2: Network Implementation - Switching
VLANs, Access Ports, Trunks, and Native VLAN STP/RSTP Loop Prevention and Bridge Roles Port Aggregation/LACP, MTU, Jumbo Frames, and Interface Settings Switch Implementation PBQs and Common Misconfigurations
7 Domain 2: Network Implementation - Wireless and Physical Implementation
Wi-Fi Standards, Bands, and Channels SSID Security, Guest Networks, and Authentication Antennas, Coverage, Roaming, Interference, and Site Surveys Physical Installation Implications
8 Domain 2: Network Implementation - Services Implementation
DNS Record Types and Troubleshooting Cues DHCP, DHCPv6, SLAAC, Scopes, Leases, and Relay NTP, PTP, NTS, and Time-Sensitive Networking Service Implementation PBQs: DNS, DHCP, VLANs, and Firewall Direction
9 Domain 3 Part A: Network Operations Documentation and Governance
Physical, Logical, Rack, Cable, Wireless Diagrams, and IPAM Asset Inventory, Baselines, SLAs, SOPs, and Runbooks Change Management and Request Tracking Lifecycle, EOL, EOS, Decommissioning, and Configuration Management
10 Domain 3 Part B: Monitoring, Remote Access, and Resilience
SNMP, Flow, Syslog, Packet Capture, Log Aggregation, APIs, and Port Mirroring Baselines and Performance Metrics Remote Access, Management Paths, and Secure Admin Habits DR and HA Concepts: RPO, RTO, MTTR, MTBF, Sites, Failover, and Testing
11 Domain 4: Logical Security and Secure Access (14%)
Encryption in Transit, Encryption at Rest, PKI, and Certificates IAM, MFA, SSO, Directory Services, and AAA Authorization, Least Privilege, RBAC, Geofencing, and Time-Based Access VPNs and Secure Management Design
12 Domain 4: Segmentation, Risk, and Network Attacks (14%)
Segmentation for Guest, BYOD, IoT, IIoT, SCADA, ICS, and OT Risk, Compliance, Audit, Data Locality, PCI, and GDPR Network Attacks and Scenario Cues Attack-to-Mitigation PBQ Tables
13 Domain 4: Security Controls and Hardening (14%)
Firewalls, IDS, IPS, Security Zones, and Screened Subnets ACLs, Filtering, NAC, Hardening, and Key Management Deception Technologies and Physical Security Zero Trust, SASE, and Trusted or Untrusted Zone Decisions
14 Domain 5: Troubleshooting Methodology and Tools (24%)
Official Troubleshooting Methodology and Evidence Handling Command-Line Tools: ping, traceroute, nslookup, dig, ipconfig, ifconfig, ip, arp, netstat, ss, and route Packet, Protocol, and Wi-Fi Analyzers Choosing the Right Tool by Symptom PBQs
15 Domain 5: Physical, Interface, and Wireless Troubleshooting (24%)
Cable Issues: Type, Attenuation, Crosstalk, Termination, and TX/RX Interface Issues: Errors, Discards, Duplex, Speed, Port Status, and PoE Transceiver, Fiber, and Signal Strength Troubleshooting Wireless Troubleshooting: Interference, Channels, Roaming, RSSI/SNR, Security, and Captive Portals
16 Domain 5: Network Services, Switching, Routing, and Performance Troubleshooting (24%)
DHCP, DNS, NTP, and IP Addressing Issues VLAN, STP, Trunk, Native VLAN, and ACL Issues Routing, Default Gateway, Route Table, and NAT Issues Congestion, Latency, Jitter, Packet Loss, and Application Performance Clues
17 Performance-Based Question Labs
Subnetting and VLSM Design Lab VLAN, Trunk, Router-on-a-Stick, and Firewall Rule Lab Wireless Deployment and Troubleshooting Lab Monitoring, Log Triage, and Route or Service Troubleshooting Lab
18 High-Yield Reference and Final Study Plan
High-Yield Ports and Protocols Table Wi-Fi, Cabling, Connectors, and Transceivers Quick Table Acronyms and Command-Line Tool Quick Table Final 7-Day Review Plan and Readiness Checklist
19 Final Synthesis: Strategy, Remediation, and Readiness
Mixed-Set Decision Strategy for Qualifiers and Close Answers Missed-Question Remediation Notebook by Error Type Exam-Day Time Management and PBQ Order 100-Question Readiness Simulation Blueprint Mapped to N10-009 Weights
Antennas, Coverage, Roaming, Interference, and Site Surveys
Key Takeaways Explain This Topic AI
Omnidirectional antennas cover broadly; directional types (patch, Yagi, parabolic) focus energy and gain in one direction.
SNR is a better quality indicator than RSSI alone, and high channel utilization signals airtime congestion.
Roaming is client-driven, but AP placement, ~15-20% cell overlap, matched SSID/security, and power tuning enable seamless handoff.
Interference can crush throughput even at full signal bars - from neighboring APs, Bluetooth, microwaves, or building materials.
Survey types build on each other: predictive (modeling), passive (listen), active (test traffic), then post-deployment validation.
Last updated: June 2026
RF Design, Not Just "Turn On the AP"
Wireless implementation accounts for building materials, client density, antenna patterns, application needs, and interference. The exam expects you to reason about coverage versus capacity and to pick antennas and survey methods for a stated scenario.
Antenna Types
Antennas do not add power - gain simply focuses the same energy into a tighter shape, raising signal in one direction while shrinking it elsewhere. Gain is measured in dBi .
- Antenna Pattern Use case
- Omnidirectional Broad horizontal donut Ceiling-mounted general office coverage
- Patch / panel Directional, flat Wall-mounted coverage into one room/zone
- Yagi Focused directional Medium point-to-point, targeted aisles
- Parabolic / dish Very narrow beam Long-distance point-to-point links
A long warehouse aisle wants a directional antenna firing down the aisle; an open office wants omnidirectional ceiling APs. A useful mental model: increasing gain on an omnidirectional antenna flattens the donut, extending horizontal reach but creating a dead zone directly below a ceiling mount, which matters in multi-story buildings. Directional antennas concentrate the same energy into a cone, which is why a Yagi or parabolic dish can bridge two buildings across a parking lot where an omnidirectional AP would never reach.
Always confirm both ends of a point-to-point link use aimed, line-of-sight directional antennas of compatible gain.
Coverage vs Capacity Metrics
- Metric Meaning Why it matters
- RSSI Received signal strength (negative dBm; -65 is better than -80) How loud the AP is at the client
- Noise floor Background RF energy Higher noise erodes usable quality
- SNR Signal-to-noise ratio (dB) Better quality indicator than RSSI alone; aim for 20-25 dB+ for voice
- Channel utilization Percent of airtime in use High values cause latency and retries
- Retry rate Frames resent Flags interference, weak signal, or contention
Strong signal everywhere can still fail if too many clients share one channel's airtime. Voice and video need low latency and jitter plus fast roaming, not just bars. RSSI is reported as a negative number in dBm , where closer to zero is stronger: -50 dBm is excellent, -70 dBm is the rough usable floor for data, and signals weaker than about -80 dBm drop. But two cells at the same RSSI can perform very differently if one sits in a noisier environment, which is exactly why SNR - the gap between signal and noise floor - is the better quality metric.
Voice deployments typically target 20-25 dB of SNR and under 30 percent channel utilization; exceed those and calls choppy even at full bars.
Roaming
Roaming is a client moving between APs. The client decides when to roam, but infrastructure shapes the decision. Common failures:
AP power set too high, so a sticky client clings to a distant AP at poor SNR.
Insufficient cell overlap (aim for roughly 15-20%) creates dead spots mid-roam.
Slow re-authentication causes voice gaps during handoff.
Mismatched SSID names or security settings block seamless movement.
Fast-roaming standards reduce re-auth time: 802.11r (fast BSS transition), 802.11k (neighbor reports), and 802.11v (BSS transition management). They require compatible clients. For most questions, focus on fundamentals: placement, power, overlap, and consistent SSID/security.
Interference Sources
- Source Symptom Response
- Neighboring APs High utilization / co-channel Re-plan channels and power
- Bluetooth 2.4 GHz contention Steer clients to 5/6 GHz
- Microwave oven Periodic 2.4 GHz dropouts Relocate APs or change band
- Metal racking / concrete Dead zones, multipath Move AP or change antenna
- Excessive AP power Sticky clients Lower transmit power
Do not equate interference with weak signal - it degrades throughput at full bars .
Site Surveys
- Survey type Purpose
- Predictive Models coverage from floor plans before install
- Passive Listens to existing RF and beacons (no association)
- Active Associates and tests roaming, throughput, application behavior
- Post-deployment validation Confirms the live WLAN meets requirements
Outputs include heat maps for signal, SNR, channel utilization, and coverage gaps, plus documented AP locations, mounting height, antenna orientation, and cable paths. The exam wants you to match the survey type to the project phase: a predictive survey is the only option before any hardware is racked, a passive survey shows what RF already exists (including rogue APs and neighbor interference) without joining the network, and an active survey is the only one that measures real throughput, retries, and roaming because the laptop actually associates and passes traffic.
Post-deployment validation closes the loop by proving the installed WLAN meets the documented requirement, not just the model.
PBQ-Style Survey Scenario
Facts: a hospital wing has new wireless medical carts; users report drops when moving between rooms; heat maps show strong 2.4 GHz but high channel utilization; some APs sit above metal equipment.
Run an active survey using the actual carts.
Review SNR, retries, utilization, and roaming logs.
Reposition APs blocked by metal (multipath/dead zones).
Tune transmit power to break sticky-client behavior.
Prefer 5/6 GHz where clients and requirements allow.
The goal is not maximum signal everywhere - it is enough clean signal and capacity for the application, with predictable roaming.