Study guide
5.7 Evaluating Waste Management, Refuse, & Recyclables Handling
NEHA CP-FS Certified Professional - Food Safety Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Overview
1.1 CP-FS Exam Format, Scoring, Eligibility & Renewal 1.2 The Official Seven-Area Blueprint & Your Study Plan
2 Chapter 2: Foundations — Food Safety Hazards & Risk Factors
2.1 The Five CDC Risk Factors, Contamination Sources & Active Managerial Control 2.2 Foodborne Pathogens: Bacteria & Bacterial Toxins 2.3 Foodborne Pathogens: Viruses, Parasites, & Fungi 2.4 Microbial Growth Dynamics (FAT TOM, pH, Aw, Temperature) 2.5 Chemical, Physical, & Allergen Contaminants
3 Chapter 3: Developing Food Safety Policies, Procedures & Programs (Area A)
3.1 Prerequisite Programs (GMPs, SOPs, SSOPs, & GRPs) 3.2 Developing Allergen Control Procedures 3.3 Employee Health, Hygiene Policies, & Exclusion/Restriction 3.4 Developing an Integrated Pest Management (IPM) Plan 3.5 Cleaning vs. Sanitizing: Chemical Sanitizers & Thermal Methods 3.6 Transportation & Receiving Procedures 3.7 Food Preparation Policies & Determining When a Variance Is Required
4 Chapter 4: HACCP Plans, Training & Root Cause Analysis (Area A)
4.1 HACCP Principles 1 to 3: Hazard Analysis, CCPs, & Critical Limits 4.2 HACCP Principles 4 to 7: Monitoring, Corrective Actions, Verification, & Recordkeeping 4.3 FSMA Preventive Controls & HARPC vs. Traditional HACCP 4.4 Establishing, Administering & Documenting Employee Training 4.5 Root Cause Analysis, Corrective Action Plans, & Continuous Improvement
5 Chapter 5: Assessing Food Safety I — Preparing For & Conducting the Assessment (Area B)
5.1 Preparing for an Inspection: Equipment, Calibration, Scheduling & Compliance History 5.2 Risk Categories & Determining Assessment Frequency 5.3 Menu Review, Approved Sources & Food Labeling 5.4 FDA Food Code: Time/Temperature Control for Safety (TCS) Foods 5.5 Managing the Flow of Food & Assessing Cross-Contamination 5.6 Evaluating Chemical Handling, SDS, & Hazardous Materials Storage 5.7 Evaluating Waste Management, Refuse, & Recyclables Handling
6 Chapter 6: Assessing Food Safety II — Special Processes, Findings & Follow-Up (Area B)
6.1 Recognizing Special Processes & Specialized Equipment 6.2 Interpreting Test Results: pH, Water Activity, Shelf Stability & Dairy Sampling 6.3 Evaluating HACCP Plans & Administrative Documentation 6.4 Master Cleaning Schedules & Environmental Monitoring Programs 6.5 Assessing Pest Control Practices & Employee Behaviors 6.6 Documenting Findings, Corrective Action Plans & Risk Control Plans 6.7 Communicating with the PIC, Educating Staff, & Enforcement Actions
7 Chapter 7: Reviewing Establishment Plans (Area C)
7.1 U.S. Food Regulatory Structure & Researching Local Laws 7.2 Plan Review Submissions: Licenses, Permits & Variances 7.3 Site Plans, Menu-to-Site Fit & Hygienic Facility Layout 7.4 Physical Facility: Walls, Floors, Ceilings, Lighting & Ventilation 7.5 Plumbing, Cross-Connections, Backflow Prevention, & Water Supply 7.6 Hot Water Demand, Warewashing, Handwashing & Restroom Needs 7.7 Equipment Certification (NSF/ANSI), Storage Needs, & Pre-Opening Verification
8 Chapter 8: Investigating Foodborne Illness (Area D)
8.1 Principles of Foodborne Epidemiology & Outbreak Detection 8.2 Complaint Intake, Agency Notification & Stakeholder Communication 8.3 Case Definitions, Case Interviews, & the 72-Hour Food History 8.4 Facility Investigation, Environmental Assessment, & Sample Collection 8.5 Employee Impacts, Exclusion & Holding Food for Disposition 8.6 Traceback Methodology, Crisis Communication & Illness Reports
9 Chapter 9: Performing Recall Activities (Area E)
9.1 Recall Classification, Implicated Products & Regulatory Submissions 9.2 Traceability Procedures, Mock Recalls & Staff Training 9.3 Recall Communication, Effectiveness Checks & Product Disposition
10 Chapter 10: Managing Food Defense Practices (Area F)
10.1 Food Defense Planning (ALERT & CARVER+Shock Models) 10.2 Vulnerability Assessments, Tamper-Evident Packaging, & Supply Chain Security 10.3 Enforcement Protocols, Training, Drills & Post-Event Analysis
11 Chapter 11: Responding to Emergencies (Area G)
11.1 Imminent Health Hazards: Power Outages, Water Interruptions, & Fires 11.2 The Response Team, Segregating Food & Regulatory Notification 11.3 Recovery Plans, Infrastructure Assessment & Reopening Verification
5.7 Evaluating Waste Management, Refuse, & Recyclables Handling
Key Takeaways Explain This Topic AI
Indoor garbage containers must be leak-proof, waterproof, pest-proof, and covered when full or not in continuous active use.
Outdoor refuse storage pads must be constructed of smooth, non-absorbent concrete/asphalt sloped to a drain, with tight-fitting lids kept closed and drain plugs in place.
Grease interceptors must be maintained under the '25% Rule', requiring pumping when combined floating grease and settled solids exceed 25% of total liquid depth.
Garbage pulpers and compactors reduce organic solid waste volume by up to 80%, squeezing out moisture and lowering pest attraction.
Refuse and recyclables must be removed from the premises frequently enough (at least daily or on scheduled pickups) to eliminate pest harborage and odors.
Last updated: August 2026
5.7 Evaluating Waste Management, Refuse, & Recyclables Handling
Exam Key: Improper handling of solid waste and liquid grease creates prime harborage for insects, rodents, and pathogenic bacteria. NEHA CP-FS candidates must know indoor container specifications, outdoor refuse pad standards, dumpster drain plug rules, and grease trap cleaning protocols.
Indoor Garbage & Recycling Container Standards
Indoor refuse containers are essential for collecting food scraps, packaging, and trash during daily operations.
Sanitary Construction Criteria
Containers used inside food establishments must be:
Durable & Non-Absorbent: Constructed of heavy-gauge plastic, high-density polyethylene (HDPE), or galvanized metal.
Leak-Proof & Waterproof: Seamless construction to prevent liquid waste from seeping onto kitchen floors.
Pest-Proof & Easily Cleanable: Smooth interior surfaces free of sharp angles or internal seams.
Operational Container Rules
Liners: Containers must be lined with heavy-duty plastic trash bags to facilitate hygienic emptying.
Covering Requirements: Indoor containers must be kept covered when full, or when not in continuous active use by staff. Continuous-use trash cans at line prep stations may remain uncovered during active prep but must be covered at shift end.
Washing Protocols: Indoor containers must be cleaned frequently. Cleaning MUST occur at an outdoor wash pad or designated utility/mop sink— NEVER inside food prep sinks or warewashing sinks .
Outdoor Refuse Storage Standards
Outdoor refuse storage areas house bulk dumpsters, trash compactors, recyclable card containers, and waste grease rendering barrels. OUTDOOR DUMPSTER PAD DESIGN
- +-----------------------------------------------------------------+
- | Concrete Pad: Smooth, Non-Absorbent, Heavy-Duty Concrete |
- | Slope: Sloped toward a designated drainage collection point |
- | |
- | +-----------------------+ +-----------------------+ |
- | | Outdoor Dumpster | | Grease Rendering | |
- | | - Tight Lid CLOSED | | - Sealed Lid CLOSED | |
- | | - Drain Plug IN PLACE| | - Elevated on Stand | |
- | +-----------------------+ +-----------------------+ |
- +-----------------------------------------------------------------+
- Structural Pad Standards
Outdoor dumpsters and compactors must be positioned on an approved storage pad:
Material: Smooth, durable, non-absorbent concrete or asphalt .
Structural Load: Concrete pads must be reinforced to support heavy commercial dumpster trucks without cracking or settling.
Sloped Drainage: Pads must be sloped to a drain connected to a grease trap or sewer to catch wash water and accidental spills.
Dumpster Maintenance & Operational Mandates
Tight-Fitting Lids: Dumpsters, compactors, and grease barrels must feature tight-fitting lids, doors, and covers that remain CLOSED at all times when not in immediate use.
Drain Plug Requirement: Outdoor dumpsters manufactured with bottom wash-out drain holes MUST keep the drain plug securely in place at all times . Plugs may only be removed during active interior washing on an approved pad and must be replaced immediately after.
Distance & Pest Exclusion: Storage areas must be located away from exterior entrance doors, loading docks, and fresh air intake vents to eliminate odor drift and pest attraction.
Grease Interceptors & Trap Maintenance
Commercial kitchens generate significant volumes of Fats, Oils, and Grease (FOG) from pot washing, fryers, and dishwashing. FOG entering municipal sewer lines cools, solidifies, and causes catastrophic sewer blockages.
Grease Trap Function & Location
Grease traps (indoor units) and grease interceptors (large outdoor underground tanks) separate FOG from wastewater before it discharges into the sewer.
Location: Installed in the drainage line serving pot sinks, dishwashers, and floor drains. Must be accessible for inspection and pumping.
The 25% Rule for Maintenance Grease Trap Cleaning Required When: ( Depth of Floating Grease + Depth of Settled Solids ) ≥ 25 % of Total Liquid Depth \text{Grease Trap Cleaning Required When: } (\text{Depth of Floating Grease} + \text{Depth of Settled Solids}) \ge 25\% \text{ of Total Liquid Depth} Grease Trap Cleaning Required When: ( Depth of Floating Grease + Depth of Settled Solids ) ≥ 25% of Total Liquid Depth +-------------------------------------------------------+
- | GREASE TRAP CROSS-SECTION |
- |=================== [ Floating Grease Layer ] ========| <--- Top 10-15%
- | |
- | [ Liquid Wastewater ] |
- | |
- |................... [ Settled Solid Sludge ] .........| <--- Bottom 10%
- +-------------------------------------------------------+
- *** Total FOG + Solids must not exceed 25% ***
Mandatory Action: When the total accumulated FOG and solids reach 25% of the trap's total fluid capacity, the unit loses hydraulic efficiency, allowing grease to pass into the municipal system. It must be completely pumped out, scraped, and cleaned by a licensed waste contractor.
Waste Pulpers & Volume Reduction
Modern food facilities utilize mechanical waste handling equipment to process solid organic waste.
Garbage Disposals: High-torque grinders installed in scrap sinks that shred food scraps into fine slurry; require continuous cold water flow during operation.
Waste Pulpers & Compactors: Advanced systems that grind organic food waste and cardboard with water, then press the slurry through a dewatering centrifuge. Pulpers extract up to 80% of the water weight , reducing total waste volume dramatically.
Benefits: Lowers commercial waste hauling fees, minimizes liquid leakage in outdoor dumpsters, and reduces foul odor generation.
Waste Removal Frequency & Pest Prevention
Accumulated trash is the primary attractant for rodents (rats, mice), insects (cockroaches, flies), and birds.
Operational Removal Protocols
Indoor Frequency: Garbage and recyclables must be removed from food prep areas at least daily , or as soon as containers become full.
Outdoor Pickups: Commercial hauling pickups must be scheduled frequently enough (multi-weekly) to prevent dumpsters from overflowing.
Recyclables Storage: Cardboard boxes must be broken down flat and stored in clean, dry recycling bins. Empty beverage cans and bottles must be rinsed before storage to prevent fly breeding.