Study guide
7.4 Physical Facility: Walls, Floors, Ceilings, Lighting & Ventilation
NEHA CP-FS Certified Professional - Food Safety Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Overview
1.1 CP-FS Exam Format, Scoring, Eligibility & Renewal 1.2 The Official Seven-Area Blueprint & Your Study Plan
2 Chapter 2: Foundations — Food Safety Hazards & Risk Factors
2.1 The Five CDC Risk Factors, Contamination Sources & Active Managerial Control 2.2 Foodborne Pathogens: Bacteria & Bacterial Toxins 2.3 Foodborne Pathogens: Viruses, Parasites, & Fungi 2.4 Microbial Growth Dynamics (FAT TOM, pH, Aw, Temperature) 2.5 Chemical, Physical, & Allergen Contaminants
3 Chapter 3: Developing Food Safety Policies, Procedures & Programs (Area A)
3.1 Prerequisite Programs (GMPs, SOPs, SSOPs, & GRPs) 3.2 Developing Allergen Control Procedures 3.3 Employee Health, Hygiene Policies, & Exclusion/Restriction 3.4 Developing an Integrated Pest Management (IPM) Plan 3.5 Cleaning vs. Sanitizing: Chemical Sanitizers & Thermal Methods 3.6 Transportation & Receiving Procedures 3.7 Food Preparation Policies & Determining When a Variance Is Required
4 Chapter 4: HACCP Plans, Training & Root Cause Analysis (Area A)
4.1 HACCP Principles 1 to 3: Hazard Analysis, CCPs, & Critical Limits 4.2 HACCP Principles 4 to 7: Monitoring, Corrective Actions, Verification, & Recordkeeping 4.3 FSMA Preventive Controls & HARPC vs. Traditional HACCP 4.4 Establishing, Administering & Documenting Employee Training 4.5 Root Cause Analysis, Corrective Action Plans, & Continuous Improvement
5 Chapter 5: Assessing Food Safety I — Preparing For & Conducting the Assessment (Area B)
5.1 Preparing for an Inspection: Equipment, Calibration, Scheduling & Compliance History 5.2 Risk Categories & Determining Assessment Frequency 5.3 Menu Review, Approved Sources & Food Labeling 5.4 FDA Food Code: Time/Temperature Control for Safety (TCS) Foods 5.5 Managing the Flow of Food & Assessing Cross-Contamination 5.6 Evaluating Chemical Handling, SDS, & Hazardous Materials Storage 5.7 Evaluating Waste Management, Refuse, & Recyclables Handling
6 Chapter 6: Assessing Food Safety II — Special Processes, Findings & Follow-Up (Area B)
6.1 Recognizing Special Processes & Specialized Equipment 6.2 Interpreting Test Results: pH, Water Activity, Shelf Stability & Dairy Sampling 6.3 Evaluating HACCP Plans & Administrative Documentation 6.4 Master Cleaning Schedules & Environmental Monitoring Programs 6.5 Assessing Pest Control Practices & Employee Behaviors 6.6 Documenting Findings, Corrective Action Plans & Risk Control Plans 6.7 Communicating with the PIC, Educating Staff, & Enforcement Actions
7 Chapter 7: Reviewing Establishment Plans (Area C)
7.1 U.S. Food Regulatory Structure & Researching Local Laws 7.2 Plan Review Submissions: Licenses, Permits & Variances 7.3 Site Plans, Menu-to-Site Fit & Hygienic Facility Layout 7.4 Physical Facility: Walls, Floors, Ceilings, Lighting & Ventilation 7.5 Plumbing, Cross-Connections, Backflow Prevention, & Water Supply 7.6 Hot Water Demand, Warewashing, Handwashing & Restroom Needs 7.7 Equipment Certification (NSF/ANSI), Storage Needs, & Pre-Opening Verification
8 Chapter 8: Investigating Foodborne Illness (Area D)
8.1 Principles of Foodborne Epidemiology & Outbreak Detection 8.2 Complaint Intake, Agency Notification & Stakeholder Communication 8.3 Case Definitions, Case Interviews, & the 72-Hour Food History 8.4 Facility Investigation, Environmental Assessment, & Sample Collection 8.5 Employee Impacts, Exclusion & Holding Food for Disposition 8.6 Traceback Methodology, Crisis Communication & Illness Reports
9 Chapter 9: Performing Recall Activities (Area E)
9.1 Recall Classification, Implicated Products & Regulatory Submissions 9.2 Traceability Procedures, Mock Recalls & Staff Training 9.3 Recall Communication, Effectiveness Checks & Product Disposition
10 Chapter 10: Managing Food Defense Practices (Area F)
10.1 Food Defense Planning (ALERT & CARVER+Shock Models) 10.2 Vulnerability Assessments, Tamper-Evident Packaging, & Supply Chain Security 10.3 Enforcement Protocols, Training, Drills & Post-Event Analysis
11 Chapter 11: Responding to Emergencies (Area G)
11.1 Imminent Health Hazards: Power Outages, Water Interruptions, & Fires 11.2 The Response Team, Segregating Food & Regulatory Notification 11.3 Recovery Plans, Infrastructure Assessment & Reopening Verification
7.4 Physical Facility: Walls, Floors, Ceilings, Lighting & Ventilation
Key Takeaways Explain This Topic AI
Floors, walls, and ceilings in food preparation, warewashing, and walk-in areas must be smooth, durable, nonabsorbent, and easily cleanable.
Floor and wall junctures in areas subject to moisture must be coved and closed to no larger than 1/32 inch under the Food Code; many jurisdictions specify a coved base with a defined radius in plan review.
Light intensity requirements are 50 foot-candles where employees work with food or sharp equipment, 20 foot-candles at surfaces in preparation and utensil areas and in walk-in refrigeration and dry storage, and 10 foot-candles in other areas during cleaning.
Light bulbs in areas with exposed food, equipment, or single-service articles must be shielded, coated, or otherwise shatter-resistant.
Ventilation must remove grease, heat, steam, and vapors, and every exhaust hood needs balanced makeup air to avoid negative pressure and backdrafting.
Last updated: August 2026
7.4 Physical Facility: Walls, Floors, Ceilings, Lighting & Ventilation
Exam Tip: This section is dense with numbers, and numbers are the easiest points on the exam. Learn the three lighting levels and the coving rule verbatim.
Finish Requirements by Area
The governing standard is that surfaces must be smooth, durable, nonabsorbent, and easily cleanable in the areas where cleanability matters most.
Area Floor Walls Ceiling
Food preparation Smooth, durable, nonabsorbent, nonslip, coved at wall juncture Smooth, nonabsorbent, light-colored, washable Smooth, nonabsorbent, washable
- Warewashing As above; sloped to a floor drain As above, moisture resistant to splash height As above
- Walk-in refrigeration As above, coved As above As above
- Restrooms Nonabsorbent, coved Nonabsorbent to splash height Washable
- Dry storage Cleanable Cleanable Cleanable
- Dining area Cleanable; carpet permitted if closely woven and securely attached Cleanable Cleanable
Materials that fail the standard in wet areas: unsealed concrete, unsealed wood, standard drywall without a moisture-resistant finish, acoustic ceiling tile with a fissured or porous face, and carpet.
Acceptable floor materials in food areas include quarry tile with epoxy grout, sealed poured epoxy or urethane, and commercial-grade sealed concrete. Acceptable wall finishes include FRP (fiberglass-reinforced panel), stainless steel, epoxy-painted smooth block, and ceramic tile with sanitary grout. Ceilings should be smooth, washable panels or coated gypsum; where lay-in tile is used it must be smooth, nonabsorbent, and cleanable, and clips are commonly required to prevent lift.
Coving
The floor and wall juncture is where soil, water, and pests accumulate, and a 90-degree corner cannot be effectively cleaned.
The Food Code requires that in food establishments where cleaning methods other than water flushing are used, floor and wall junctures be coved and closed to no larger than 1 mm (one thirty-second inch) .
In areas subject to water flush cleaning , floors must be graded to drain and the juncture must be coved and sealed.
Plan review practice in most jurisdictions goes further, specifying an integral or applied coved base with a defined radius — commonly 3/8 inch — because a curved transition can actually be mopped. Check the adopted local requirement rather than assuming a number.
Cove base must be integral or sealed to both floor and wall. A vinyl base stuck on with adhesive that lifts at the bottom edge is a harborage, and it is one of the most frequently cited plan-review-related deficiencies at the pre-operational inspection.
Lighting
Three levels, and the exam expects all three.
Level Where required
50 foot-candles (540 lux) At surfaces where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor
20 foot-candles (215 lux) At a surface where food is provided for consumer self-service or where fresh produce or packaged foods are sold; inside equipment such as reach-in and under-counter refrigerators ; at a distance of 30 inches above the floor in areas used for handwashing, warewashing, equipment and utensil storage, and in toilet rooms
10 foot-candles (108 lux) At a distance of 30 inches above the floor in walk-in refrigeration units and dry food storage areas , and in other areas and rooms during periods of cleaning
Shielding
Light bulbs must be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food, clean equipment, utensils, linens, or unwrapped single-service and single-use articles . Two exemptions worth knowing: shielding is not required where a shatter-resistant bulb is used, and infrared or heat lamps must be protected against breakage by a shield surrounding and extending beyond the bulb so that only the face is exposed.
A broken unshielded bulb over an open prep table is a physical hazard event — the food beneath must be discarded and the area cleaned before work resumes.
Ventilation
Ventilation systems must be designed so that grease, heat, steam, condensation, vapors, obnoxious odors, smoke, and fumes are removed , and so that they do not create a nuisance or a contamination pathway.
Element Requirement or consideration
Hood type Type I over grease-producing appliances (fryers, griddles, ranges, broilers); Type II over steam and heat-only appliances (dishwashers, ovens without grease)
Capture and containment The hood must capture the plume; overhang and capture velocity are engineering parameters verified in plan review
Filters Removable, cleanable, tight-fitting, at an angle so grease drains to a collection trough; not to be run through the dish machine with utensils
Duct and fan cleaning Scheduled by cooking volume and fuel type; a documented service record is expected
Fire suppression Wet chemical system, interlocked to shut down fuel and to activate on discharge; inspected semiannually in most jurisdictions
Makeup air Required. An exhaust system without balanced makeup air creates negative building pressure
Air balance Positive or neutral pressure in food preparation areas; airflow should move from clean areas toward dirty areas, never the reverse
- Intake location Fresh air intakes located away from exhaust discharge, dumpsters, and loading docks
- Restroom exhaust Mechanically vented to the outside
- Why makeup air matters
Running a large exhaust hood without an equivalent supply of makeup air pulls the building into negative pressure . Three consequences follow:
Backdrafting. Combustion gases — including carbon monoxide — from gas-fired water heaters, boilers, and furnaces are pulled back down their flues into the building instead of venting.
Poor hood capture. The hood starves for air and stops containing the plume, so grease and steam spill into the kitchen.
Uncontrolled infiltration. Air is drawn in through door gaps, drains, and wall penetrations, bringing dust, odors, and insects with it. Doors become hard to open.
A plan reviewer checks the mechanical schedule for exhaust CFM and makeup CFM and looks for a balance. A large deficit is a design defect, not a commissioning detail.
Other Physical Facility Items in Plan Review
Outer openings protected — self-closing solid doors, screens at 16 mesh to the inch or finer, air curtains where permitted, and sealed penetrations for utilities
Dressing rooms and lockers provided where employees change clothes routinely, located outside food and utensil storage areas
A service sink or curbed cleaning facility with a floor drain for mop water disposal — required, and frequently missing from plans
- Storage of mops and brooms in a position that allows air drying
- Living or sleeping quarters separated from food establishment operations
Animals excluded, with defined exceptions such as service animals in dining areas and patrol dogs in some settings