Study guide
2.2 Soil Identification, NRCS Soil Surveys & Hydrologic Soil Groups
Certified Professional in Erosion and Sediment Control CPESC
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Rules, Regulations & Clean Water Act Framework
1.1 Federal Clean Water Act & NPDES Regulatory Framework 1.2 Construction General Permit (CGP), NOI/NOT & State/Local Jurisdiction 1.3 CWA Sections 401, 404 & Specialized Environmental Laws
2 Chapter 2: Site Assessment, Watershed Delineation & Resource Inventory
2.1 Topographic Analysis, Drainage Areas & Watershed Delineation 2.2 Soil Identification, NRCS Soil Surveys & Hydrologic Soil Groups 2.3 Environmental Site Constraints, Receiving Waters & Sensitive Areas
3 Chapter 3: Site Planning, Construction Sequencing & Hazard Management
3.1 Land Disturbance Minimization & Construction Phasing 3.2 Construction Scheduling, Seasonal Windows & Buffer Zones 3.3 Site Hazard Identification & Clearing/Grading Limits
4 Chapter 4: Soil Erosion Mechanics & Types
4.1 Fundamentals of Erosion & the Sedimentation Cycle 4.2 Mechanics of Water Erosion: Splash, Sheet, Rill & Gully 4.3 Channel, Stream Bank, Shoreline & Wind Erosion
5 Chapter 5: Soil Loss Prediction: USLE, RUSLE & MUSLE
5.1 Universal Soil Loss Equation (USLE/RUSLE) Overview & R-Factor 5.2 Soil Erodibility Factor (K) & Topographic Factor (LS) 5.3 Cover Management Factor (C) & Support Practice Factor (P) 5.4 Modified USLE (MUSLE) & Single-Storm Sediment Yield
6 Chapter 6: Runoff Hydrology & Watershed Modeling
6.1 Hydrologic Cycle, Runoff Generation & Time of Concentration 6.2 The Rational Method (Q = CiA) & Peak Runoff Estimation 6.3 NRCS (SCS) Curve Number Method & Runoff Volume Estimation
7 Chapter 7: Runoff Conveyance & Open Channel Hydraulics
7.1 Manning's Equation & Open Channel Flow Hydraulics 7.2 Temporary Diversion Dikes, Berms & Swales 7.3 Grade Stabilization Structures, Check Dams & Flumes
8 Chapter 8: Soil Preparation, Fertility & Revegetation
8.1 Soil Testing, pH Adjustment & Nutrient Management (N-P-K) 8.2 Soil Amendments, Compost Incorporation & Seedbed Preparation 8.3 Plant Selection: Native vs. Non-Native, Turf vs. Woody, Cool vs. Warm Season 8.4 Seeding Methods, Nurse Crops & Hydroseeding Application
9 Chapter 9: Mulching & Rolled Erosion Control Products (RECPs)
9.1 Mulch Types, Hydraulic Mulches & Bonded Fiber Matrices (BFMs) 9.2 Rolled Erosion Control Products (RECPs): Temporary ECBs 9.3 Turf Reinforcement Mats (TRMs) & Permanent Vegetative Armoring 9.4 Hard Armoring: Riprap, Gabions, Articulated Concrete & Cellular Confinement
10 Chapter 10: Perimeter Sediment Barriers & Filtration Controls
10.1 Silt Fence Design, Trenching, Installation & Maintenance 10.2 Vegetative Buffer Strips, Compost Filter Socks & Fiber Rolls (Wattles) 10.3 Gravel Bag Berms, Sandbag Barriers & Brush Barriers
11 Chapter 11: Storm Drain Inlet Protection & Slope Drains
11.1 Drop Inlet Protection: Silt Fence, Wire Mesh & Manufactured Inserts 11.2 Curb Inlet Protection: Gravel Berms, Filter Socks & Foam Inserts 11.3 Temporary & Permanent Pipe Slope Drains and Subsurface Drains
12 Chapter 12: Sediment Traps, Basins & Active Treatment
12.1 Sediment Traps: Design Criteria, Sizing & Maintenance 12.2 Sediment Basins: Sizing (Volume & Surface Area), Length-to-Width Ratio 12.3 Basin Outflow Structures: Skimmers, Perforated Risers & Baffles 12.4 Chemical Treatment, Flocculants (PAM/Chitosan) & Jar Testing
13 Chapter 13: Non-Sediment Pollution Prevention & Good Housekeeping
13.1 Construction Site Dewatering Operations & Filtration 13.2 Concrete Washout, Masonry & Mortar Waste Management 13.3 Fuels, Petroleum, Hazardous Chemicals & Spill Response 13.4 Stabilized Construction Entrances, Tire Washes & Dust Control
14 Chapter 14: SWPPP Administration, Site Inspections & Ethics
14.1 SWPPP Elements, Site Maps & Plan Amendments 14.2 Construction Inspection Protocols, Schedules & Documentation 14.3 Turbidity Monitoring, Discharge Sampling & Corrective Action Logs 14.4 Field Education, Subcontractor Oversight & CPESC Code of Ethics
2.2 Soil Identification, NRCS Soil Surveys & Hydrologic Soil Groups
Key Takeaways Explain This Topic AI
Soil texture is governed by the proportions of sand (0.05–2.0 mm), silt (0.002–0.05 mm), and clay (< 0.002 mm), with silt being the most detachment-susceptible fraction.
Due to specific surface areas exceeding 800 sq m/g and negative electrical charges, colloidal clays stay suspended indefinitely without chemical flocculation.
Topsoil (A horizon) must be carefully stripped, stockpiled outside drainage paths, and stabilized immediately to preserve beneficial microbial biology and organic matter.
NRCS Hydrologic Soil Groups range from Group A (infiltration > 0.30 in/hr, low runoff) to Group D (infiltration < 0.05 in/hr, high runoff).
Dual hydrologic groups (e.g., A/D, B/D) indicate high seasonal water tables where the first letter applies only if artificial subsurface drainage is fully functional.
Last updated: September 2026
2.2 Soil Identification, NRCS Soil Surveys & Hydrologic Soil Groups
Soil is the fundamental medium in erosion and sediment control. The physical, chemical, and hydrologic properties of on-site soils determine their susceptibility to detachment ( erodibility ), their ability to infiltrate rainfall, their vegetative establishment potential, and the ease with which suspended particles settle out in sediment basins. A thorough pre-construction soil inventory enables the CPESC practitioner to select appropriate BMPs and predict site runoff volumes accurately.
Soil Particle Size Fractions & The USDA Textural Classification
Mineral soil is categorized into three primary particle size fractions (soil separates) according to the United States Department of Agriculture (USDA) classification system:
Sand (0.05 mm to 2.0 mm): Sand grains are visible to the naked eye, feel distinctly gritty when rubbed between the fingers, and lack cohesion when moist. Sand particles are further divided into very coarse ( 1.0 – 2.0 mm 1.0\text{–}2.0\text{ mm} 1.0 – 2.0 mm ), coarse ( 0.5 – 1.0 mm 0.5\text{–}1.0\text{ mm} 0.5 – 1.0 mm ), medium ( 0.25 – 0.5 mm 0.25\text{–}0.5\text{ mm} 0.25 – 0.5 mm ), fine ( 0.10 – 0.25 mm 0.10\text{–}0.25\text{ mm} 0.10 – 0.25 mm ), and very fine ( 0.05 – 0.10 mm 0.05\text{–}0.10\text{ mm} 0.05 – 0.10 mm ). Soils high in sand exhibit rapid infiltration rates, low moisture retention, and high structural friction.
Silt (0.002 mm to 0.05 mm): Silt particles range from 2 to 50 microns in diameter. Silt feels smooth, floury, and velvety when dry, and slippery like wet talc when moistened, lacking true stickiness. Silt is the most erodible of all soil fractions. Because silt particles have low cohesive bonding yet small individual mass, raindrop splash detaches them with ease, and overland runoff readily transports them down-slope.
Clay (< 0.002 mm / < 2 microns): Clay consists of microscopic, plate-like secondary aluminosilicate minerals. Moist clay is sticky, highly plastic, and easily molded into ribbons. When dry, clay hardens into cohesive clods that resist mechanical detachment.
Specific Surface Area and Colloidal Behavior of Clays
As particle size decreases, the ratio of surface area to mass increases exponentially:
Sand: Specific surface area is negligible, typically 0.01 to 0.1 m 2 /g 0.01\text{ to } 0.1\text{ m}^2\text{/g} 0.01 to 0.1 m 2 /g .
Silt: Specific surface area ranges from 1 to 10 m 2 /g 1\text{ to } 10\text{ m}^2\text{/g} 1 to 10 m 2 /g .
Clay: Specific surface area ranges from 10 to 800 m 2 /g 10\text{ to } 800\text{ m}^2\text{/g} 10 to 800 m 2 /g (e.g., kaolinite ≈ 10 – 20 m 2 /g \approx 10\text{–}20\text{ m}^2\text{/g} ≈ 10 – 20 m 2 /g ; illite ≈ 80 – 100 m 2 /g \approx 80\text{–}100\text{ m}^2\text{/g} ≈ 80 – 100 m 2 /g ; smectite/montmorillonite ≈ 600 – 800 m 2 /g \approx 600\text{–}800\text{ m}^2\text{/g} ≈ 600 – 800 m 2 /g ).
Clay particles behave as colloids . Due to isomorphic substitution within their crystalline lattices, clay surfaces carry permanent negative electrical charges . In aqueous suspension, these negative charges attract positive counter-ions (cations such as Ca 2 + \text{Ca}^{2+} Ca 2 + , Mg 2 + \text{Mg}^{2+} Mg 2 + , Na + \text{Na}^+ Na + ), creating a diffuse electrical double layer. When suspended clay particles approach one another, their electrostatic fields repel them, preventing natural agglomeration.
According to Stokes' Law , the settling velocity of a spherical particle in water is directly proportional to the square of its particle diameter ( v s ∝ d 2 v_s \propto d^2 v s ∝ d 2 ). While coarse sand ( 0.5 mm 0.5\text{ mm} 0.5 mm ) settles through 1 meter of still water in approximately 5 seconds, and coarse silt ( 0.02 mm 0.02\text{ mm} 0.02 mm ) settles in roughly 40 minutes, fine colloidal clay ( 0.001 mm 0.001\text{ mm} 0.001 mm ) requires over 40 to 100 days to settle through the same depth under gravity alone. In active construction sediment basins, colloidal clays will remain in suspension indefinitely, producing turbid effluent that violates discharge limits unless treated with chemical coagulants or flocculants (e.g., polyacrylamide [PAM] or chitosan).
The USDA Soil Texture Triangle
The USDA Soil Texture Triangle graphically defines 12 standard textural classes based on the relative percentages of sand, silt, and clay. A soil composed of 40 % 40\% 40% sand, 40 % 40\% 40% silt, and 20 % 20\% 20% clay is classified as a loam —an ideal balance of moisture retention, nutrient capacity, and drainage.
Soil Separate Particle Diameter Range (mm) Specific Surface Area ( m 2 / g m^2/g m 2 / g ) Field Feel When Moist Primary Erosion & Sediment Characteristics
Gravel > 2.0 mm < 0.005 Rock fragments / non-cohesive Armor layer; prevents detachment; high permeability.
Sand 0.05 to 2.0 mm 0.01 to 0.1 Gritty; does not soil hands High infiltration; low runoff; settles rapidly in sediment traps (< 1 minute).
Silt 0.002 to 0.05 mm 1.0 to 10.0 Smooth, velvety, floury; non-sticky Most erodible fraction (highest K-factor) ; easily detached; settles in 30–120 minutes.
Clay < 0.002 mm (< 2 µm) 10 to 800 Sticky, plastic; forms shiny ribbons High detachment resistance (cohesive); highly suspended colloids; requires days/weeks or chemical flocculants to settle.
Soil Profile Horizons & Topsoil Preservation
A natural soil profile develops distinct horizontal layers termed soil horizons , shaped over millennia by climate, biological activity, topography, parent material, and time:
O Horizon (Organic Layer): Surface layer dominated by partially decomposed organic matter, leaf litter, and humus. Provides natural mulch that buffers raindrop impact.
A Horizon (Topsoil): The uppermost mineral horizon, darkened by enriched organic matter. Characterized by granular structure, high biological activity (microorganisms, mycorrhizal fungi, earthworms), high available water capacity, and the natural seedbank. This is the primary vegetative rooting medium .
E Horizon (Eluvial / Leached Layer): Light-colored horizon beneath the A horizon where silicate clays, iron, and aluminum oxides have been leached down-slope by percolating water. Often sandy or silty with weak structure.
B Horizon (Subsoil / Illuvial Layer): Zone of accumulation where clays, iron, and carbonates washed down from overlying layers concentrate. Typically has blocky or prismatic structure and lower saturated hydraulic conductivity ( K s a t K_{sat} K s a t ) than the A horizon.
C Horizon (Substratum / Parent Material): Unconsolidated weathered parent material (weathered bedrock, alluvium, or glacial till) with minimal biological development. Low organic content and infertile.
R Horizon (Bedrock): Consolidated hard bedrock (granite, limestone, sandstone, basalt) that cannot be excavated with standard earthmoving equipment.
Topsoil Stripping, Stockpiling, and Preservation Protocols
Subsoils (B and C horizons) exposed during bulk earthwork are deficient in organic matter and beneficial soil biota, making vegetative re-establishment exceptionally difficult. CPESC specifications must require:
Selective Topsoil Stripping: Strip the entire native A horizon (typically 4 to 12 inches) prior to rough cut/fill grading.
Stockpile Siting: Locate topsoil stockpiles outside active construction traffic zones, away from steep grades, and at least 50 feet away from natural waterways, wetlands, and drainage swales.
Stockpile Geometry & Stabilization: Maintain stockpile side slopes at 2 : 1 2:1 2 : 1 (H:V) or flatter (preferably 3 : 1 3:1 3 : 1 ). Apply temporary seeding and hydraulic mulch or rolled erosion control products within 14 calendar days (or 7 days in sensitive watersheds) if stockpiles will remain dormant for more than 14 days.
Perimeter Containment: Install compost filter socks or silt fence around the entire base perimeter of the stockpile to capture sloughed material.
Preserving Biological Viability: Avoid operating heavy machinery over topsoil stockpiles when wet to prevent severe compaction that destroys mycorrhizal fungi and creates anaerobic, sterile conditions.
NRCS Web Soil Survey Interpretation
The Natural Resources Conservation Service (NRCS) provides digital soil geographic data through the Web Soil Survey (WSS) . CPESC professionals utilize soil survey reports to identify:
Map Units and Map Unit Symbols (MUSYM): Geographic delineations representing a specific soil series or soil complex (e.g., "CsB - Cecil sandy loam, 2 to 6 percent slopes").
Depth to Restrictive Layers: Distance from the surface to impermeable layers such as lithic bedrock, dense basal till, or a fragipan (a dense, brittle subsurface horizon that perches water and blocks plant roots).
Depth to Seasonal High Water Table (SHWT): The shallowest depth at which the soil is saturated for significant periods during wet seasons, identified in soil pits by redoximorphic features (mottles of bright red/orange iron concentrations and low-chroma gray/gleyed depletions). Siting infiltration basins or sediment basins below the SHWT causes continuous baseflow inundation, basin failure, and groundwater contamination.
Soil Erodibility Factor (K): An empirical measure of soil susceptibility to particle detachment and transport by rainfall and runoff, ranging from 0.02 (least erodible) to 0.69 (most erodible).
NRCS Hydrologic Soil Groups (HSGs)
The NRCS classifies soils into four major Hydrologic Soil Groups (HSGs) — A, B, C, and D —based on their minimum saturated infiltration rate after prolonged wetting, which directly determines their runoff potential .
Group A: Low Runoff Potential / High Infiltration
Infiltration Rate: Greater than 0.30 in/hr 0.30\text{ in/hr} 0.30 in/hr ( > 8.0 mm/hr > 8.0\text{ mm/hr} > 8.0 mm/hr ) when thoroughly wetted.
Soil Characteristics: Deep, well-drained to excessively drained sands, gravels, and loamy sands with high permeability ( K s a t > 5.0 in/hr K_{sat} > 5.0\text{ in/hr} K s a t > 5.0 in/hr ) and low runoff coefficients. Water is transmitted freely through the profile.
CPESC Application: Exceptional suitability for post-construction stormwater infiltration basins and bio-retention cells. However, unstabilized coarse sands are prone to severe wind erosion and excessive gullying in concentrated flow channels.
Group B: Moderately Low Runoff Potential / Moderate Infiltration
Infiltration Rate: 0.15 to 0.30 in/hr 0.15\text{ to } 0.30\text{ in/hr} 0.15 to 0.30 in/hr ( 4.0 to 8.0 mm/hr 4.0\text{ to } 8.0\text{ mm/hr} 4.0 to 8.0 mm/hr ) when thoroughly wetted.
Soil Characteristics: Moderately deep to deep, moderately well-drained to well-drained soils with moderately fine to moderately coarse textures (loam, silt loam, sandy clay loam). Moderate permeability and runoff generation.
CPESC Application: Readily vegetated; responsive to standard erosion control and infiltration practices.
Group C: Moderately High Runoff Potential / Slow Infiltration
Infiltration Rate: 0.05 to 0.15 in/hr 0.05\text{ to } 0.15\text{ in/hr} 0.05 to 0.15 in/hr ( 1.0 to 4.0 mm/hr 1.0\text{ to } 4.0\text{ mm/hr} 1.0 to 4.0 mm/hr ) when thoroughly wetted.
Soil Characteristics: Soils with an impeding layer that impedes the downward movement of water, or soils with moderately fine to fine textures (clay loam, silty clay loam). Saturated hydraulic conductivity is slow.
CPESC Application: Generates substantial runoff volumes during moderate storm events. Requires enlarged sediment traps and sediment basins.
Group D: High Runoff Potential / Very Slow Infiltration
Infiltration Rate: 0.00 to 0.05 in/hr 0.00\text{ to } 0.05\text{ in/hr} 0.00 to 0.05 in/hr ( 0.0 to 1.0 mm/hr 0.0\text{ to } 1.0\text{ mm/hr} 0.0 to 1.0 mm/hr ) when thoroughly wetted.
Soil Characteristics: Heavy clays with high shrink-swell potential, soils with a permanent or semi-permanent high water table, soils with a shallow claypan or hardpan near the surface, and shallow soils over nearly impervious bedrock.
CPESC Application: Generates the highest peak runoff discharges and runoff volumes. Infiltration BMPs are strictly unfeasible. Turbid colloidal clay runoff requires extended detention, surface skimmers, and chemical flocculant treatment.
Dual Hydrologic Groups: A/D, B/D, and C/D
Certain wet soils are assigned dual hydrologic groups (e.g., B/D ). The first letter represents the soil's hydrologic performance if artificially drained (via agricultural subsurface tile lines or perimeter drainage ditches), while the second letter ( D ) represents its performance in its natural, undrained condition . If a construction project destroys or removes existing agricultural subsurface drainage tiles, the soil immediately reverts to Group D hydrologic behavior, producing massive spikes in surface runoff volume.
Hydrologic Soil Group (HSG) Saturated Infiltration Rate (in/hr) Runoff Potential Typical Soil Textural Classes Siting Suitability for Stormwater Infiltration BMPs
Group A > 0.30 in/hr (> 8.0 mm/hr) Very Low Sand, loamy sand, gravelly sand High: Rapid percolation; low risk of standing water.
Group B 0.15 to 0.30 in/hr (4.0 to 8.0 mm/hr) Moderate Loam, silt loam, sandy loam Moderate to High: Favorable infiltration and moisture capacity.
Group C 0.05 to 0.15 in/hr (1.0 to 4.0 mm/hr) Moderately High Sandy clay loam, clay loam, silty clay loam Low: Restricted drainage; requires underdrains.
Group D 0.00 to 0.05 in/hr (0.0 to 1.0 mm/hr) Very High Clay, silty clay, shallow soils over rock/hardpan Unsuitable: Infiltration prohibited; high runoff generation.
Dual (A/D, B/D, C/D) Variable (Group D unless drained) High (undrained) Wet soils with seasonal high water tables Conditional: Only if engineered underdrain maintains lowered water table.
Practical Soil Texture Field Tests
When laboratory sieve and hydrometer data are unavailable, CPESC inspectors verify soil classifications using standard field methodology:
1. The Feel Test
Moisten a walnut-sized soil sample and rub it vigorously between the thumb and forefinger:
Gritty: If the sample feels scratchy and makes an audible grating sound, sand dominates (> 50%).
Floury / Velvety: If the sample feels exceptionally smooth and silky like cornstarch when moist, silt dominates.
Sticky / Plastic: If the sample feels cohesive, adheres stubbornly to the skin, and shines when smeared, clay dominates.
2. The Ribbon Test
Knead a soil sample moistened to the consistency of putty. Roll the sample into a uniform cylinder approximately 0.5 to 0.75 inches in diameter. Gradually push the cylinder upward over the forefinger using the thumb, squeezing it into a flat ribbon of uniform thickness (approx. 1/8 inch), letting it extend over the edge until it breaks under its own weight:
Less than 1.0 inch (< 2.5 cm) Ribbon: Coarse texture (sand, loamy sand, or sandy loam). Low clay content (< 15–20%).
1.0 to 2.0 inches (2.5 to 5.0 cm) Ribbon: Medium texture (loam, silt loam, sandy clay loam, or clay loam). Moderate clay content (20–40%).
Greater than 2.0 inches (> 5.0 cm) Ribbon: Fine texture (clay, silty clay, or sandy clay). High clay content (> 40%). Shows high plasticity and produces a shiny surface when burnished with a fingernail.
3. The Sedimentation Jar Test
Place a representative 1-cup soil sample into a clear, straight-sided quart glass jar. Add water until the jar is 3/4 full, along with 1 teaspoon of liquid dishwashing detergent (which serves as a surfactant/dispersant to break clay clods into individual particles). Shake vigorously for 5 minutes and place the jar on a level surface away from vibrations:
At 1 minute: All sand particles settle out to the bottom. Measure the thickness of the bottom sand layer.
At 2 hours: All silt particles settle out, forming a distinct layer above the sand. Measure the combined sand + silt thickness.
At 24 to 48 hours: Coarse clay particles settle, forming a fine, darker layer on top. Measure the clay thickness.
Calculate the relative percentage of each layer to identify the soil textural class on the USDA Soil Texture Triangle.